H3C SecPath T9000-S User manual

This manual suits for next models

1

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual

Manual version: APW101-20170630 BOM: 3123A1MQ

i

H3C SecPath T9000-S NSQM2IPSDSCA0 intrusion

prevention system service module

1 Identifier

The module identifier NSQM2IPSDSCA0 is at the upper right corner of the front panel.

2 Introduction

The H3C fourth-generation high performance intrusion prevention system service module

NSQM2IPSDSCA0 is developed for the H3C T9008-S intrusion prevention system. The module

provides features including firewall, VPN, content filtering, content identification, URL filtering, and

NAT and can greatly enhance security capabilities of the gateway.

3 Specifications

The module has a console port, a USB port, a GE copper port, and a hard disk slot

Figure 1 Front panel

(1) Captive screw (2) Ejector lever

(3) Hard disk slot (reserved) (4) Console port (CONSOLE)

(5) GE copper port (10/100/1000BASE-T) (6) USB port (reserved)

(7) Hard disk LED (HD) (8) System status LED (SYS)

Table 1 Module specifications

Item Specification

Flash 8MB Nor Flash

Memory Standard configuration: 16 GB (two 8GB VLP RDIMMs)

Micro SD card One built-in Micro SD card slot

Standard configuration: 8 GB

Dimensions (H × W × D) 40.1 × 399.2 × 376.8 mm (1.58 × 15.71 × 14.83 in)

Power consumption 116 W to 124 W

Weight 3.8 kg (8.38 lb)

Hot swapping Supported

1 2 3 4 5 6 78

Manual version: APW101-20170630 BOM: 3123A1MQ

ii

Item Specification

Ports

•1 × console port

•1 × USB port (reserved)

•1 × GE copper port

•1 × hard disk slot (reserved)

Ambient temperature

•Operating: 0°C to 45°C (32°F to 113°F)

•Not operating: –40°C to +70°C (–40°F to +158°F)

Rate of temperature change

•Operating: < 20°C (68°F)/h

•Not operating: < 30°C (86°F)/h

Ambient humidity

•Operating: 10 to 80% RH, noncondensing

•Not operating: 5 to 90% RH, noncondensing

Compatible device models and

slots T9008-S intrusion prevention system (slots 2 to 7)

Table 2 Console port specifications

Item Specification

Connector RJ-45

Interface standard RS-232

Transmission baud rate 9600 bps (default) to 115200 bps

Transmission medium Asynchronous serial cable

Transmission distance ≤15 m (49.21 ft)

Services

•Provides connection to an ASCII terminal.

•Provides connection to the serial port of a local or remote (through a

pair of modems) PC running terminal emulation program.

•Supports command line interface (CLI)

Table 3 10/100/1000BASE-T Ethernet copper port specifications

Item Specification

Connector RJ-45

Interface standard 802.3, 802.3u, and 802.3ab

Interface type MDI/MDIX autosensing

Transmission medium Category-5 (or above) twisted pair cable

Transmission distance 100 m (328.08 ft)

Transmission rate and working

mode

•10 Mbps, half/full duplex

•100 Mbps, half/full duplex

•1000 Mbps, full duplex

Manual version: APW101-20170630 BOM: 3123A1MQ

iii

4 LEDs

The module provides LEDs to show the operating status of the module and the hard disk.

Table 4 LED description

LED Status Description

Hard disk (HD)

Fast flashing green The hard disk is reading and writing data.

Steady green The hard disk is operating correctly.

System status LED (SYS)

Off No power is being input or the module is faulty.

Slowly flashing green The system has started up and is operating

correctly.

Fast flashing green The system is loading software.

5 Installing and removing the module

CAUTION:

•Wear a reliably-grounded ESD wrist strap or ESD gloves when you install or remove the module.

•Do not touch the components on the PCB.

5.1 Installing the module

1. Face the front panel of the device. Remove the filler panel from the target slot.

This example uses slot 2 on the device.

2. Place the module horizontally on a workbench with the PCB facing up. Pull outward the ejector

levers on the module.

3. Gently push the module into the slot along the guide rails.

4. Push the ejector levers inward until the module is in close contact with the backplane.

5. Use a Phillips screwdriver to tighten the captive screws on the module.

Manual version: APW101-20170630 BOM: 3123A1MQ

iv

Figure 2 Installing the module

5.2 Removing the module

1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is

released.

2. Simultaneously pull the ejector levers at both sides of the module outward to separate the

module from the backplane, and pull the module slowly out of the chassis along the guide rails.

3. Place the module on an anti-static workbench with the PCB facing up, or put it in an anti-static

bag.

4. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

6 Software upgrade

For information about upgrading the module, see the release notes.

7 Obtaining documentation

To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:

1. Go to http://www.h3c.com.hk/Technical_Documents.

2. Click Security Products, and then choose the desired product.

Copyright © 2017 New H3C Technologies Co., Ltd.