H3C SecPath NSQ1FAB12D0 User manual

Other H3C Switch manuals

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual

Manual version: 6PW106-20210319 BOM: 3123A0R1

i

H3C SecPath NSQ1FAB12D0 switching fabric module

1 Module view

The NSQ1FAB12D0 switching fabric module uses product code NSQM1FAB12D0.

Figure 1 NSQ1FAB12D0 switching fabric module

2 Specifications

Figure 2 Front panel

(1) Console port (CONSOLE) (2) Status LEDs

Table 1 Module specifications

Item Specifications

Dimensions (H × W × D) 40 × 602 × 298 mm (1.57 × 23.70 × 11.73 in)

Power consumption 195 W to 255 W

Weight 4.51 kg (9.94 lb)

Hot swapping Supported

Connector type RJ-45

Ports 1 × console port

Ambient temperature •Operating: 0°C to 45°C (32°F to 113°F)

•Storage: –40°C to +70°C (–40°F to +158°F)

Ambient humidity •Operating: 10% RH to 95% RH, noncondensing

•Storage: 5% RH to 95% RH, noncondensing

Compatible device models

and slots

•M9014 gateway (slots 14 to 17)

•T9014 IPS (slots 14 to 17)

Manual version: 6PW106-20210319 BOM: 3123A0R1

ii

IMPORTANT:

A

n M9014 gateway and a T9014 IPS each require a minimum of three switching fabric modules, and

slots 14 and 15 must be installed with switching fabric modules.

3 LEDs

The module provides LEDs to show its operating status.

Table 2 LED description

RUN LED ALM LED Description

Flashing (0.5 Hz) Off The switching fabric module is operating properly.

Off On The switching fabric module is faulty.

Flashing (0.5 Hz) On The temperature of the switching fabric module has exceeded the

upper or lower limit.

Off Off The switching fabric module has not started.

On Off The switching fabric module is starting up.

4 Installing or removing the module

CAUTION:

•Wear a well-grounded ESD-preventive wrist strap before you install or remove the module.

•When you install or remove the module, avoid touching the components on it.

4.1 Installing the module

1. Face the rear panel of the device.

2. Remove the filler panel from the target slot.

This example uses slot 15.

3. Place the module vertically with the component side facing left. Open the ejector levers and

gently push the module into the slot along the guide rails, as shown by callout 1 in Figure 3.

4. Close the ejector levers. Make sure the module is in close contact with the backplane, as shown

by callout 2 in Figure 3.

5. Use a Phillips screwdriver to fasten the captive screws on the module, as shown by callout 3

in Figure 3.

Manual version: 6PW106-20210319 BOM: 3123A0R1

iii

Figure 3 Installing the module

(1) Gently push the module into the slot along the guide rails until the module is in close contact with the

backplane.

(2) Close the ejector levers.

(3) Use a Phillips screwdriver to fasten the captive screws.

(4) Installation is finished.

4.2 Removing the module

1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is

released.

2. Simultaneously open the ejector levers on the module to separate the module from the

backplane, and pull the module slowly out of the chassis along the guide rails.

3. Place the module on an anti-static workbench or put it in an anti-static bag, with the component

side facing up.

If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

Copyright © 2021 New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.

1 2

3 4