H3C S7502 User manual
Installation Manual
H3C S7502 Ethernet Switch Table of Contents
i
Table of Contents
Chapter 5 System Commissioning..............................................................................................5-1
5.1 Configuration Environment Setup......................................................................................5-1
5.1.1 Setting up Networking Environment........................................................................5-1
5.1.2 Connecting the Console Cable ...............................................................................5-1
5.1.3 Setting Terminal Parameters ..................................................................................5-1
5.2 Power-on............................................................................................................................5-5
5.2.1 Check before Power-on ..........................................................................................5-5
5.2.2 Power-on.................................................................................................................5-6
5.2.3 Check after Power-on (Recommended) .................................................................5-6
5.2.4 Starting the Interface...............................................................................................5-6
Installation Manual
H3C S7502 Ethernet Switch Chapter 5 System Commissioning
5-1
Chapter 5 System Commissioning
5.1 Configuration Environment Setup
5.1.1 Setting up Networking Environment
A terminal (a PC in this example) is connected to the switch Console port through a
Console cable.
Console cable
PC
Switch
Serial port
Console port
Figure 5-1 Configuration environment
5.1.2 Connecting the Console Cable
Step 1: Plug the DB-9 female plug of the Console cable to the serial port of the PC or
the terminal where the switch is to be configured.
Step 2: Connect the RJ-45 connector of the Console cable to the Console port of the
switch.
5.1.3 Setting Terminal Parameters
Parameter requirements:
zBits per second: 9600
zData bits: 8
zParity: none
zStop bits: 1
zFlow control: none
zEmulation: VT100
Installation Manual
H3C S7502 Ethernet Switch Chapter 5 System Commissioning
5-2
Taking the PC running Windows XP HyperTerminal as an example, this section
introduces how to set the terminal parameters.
Note:
The terminal emulator on a Windows3.1 computer is Terminal and that on a
Windows95/Windows98/Windows 2000/Windows NT/Windows XP/Windows ME
computer is HyperTerminal.
Step 1: Start the PC and run the terminal emulator.
Step 2: Set the parameters for Windows XP HyperTerminal as follows:
1) Select Start > Programs/All Programs > Accessories > Communications >
HyperTerminal to enter the HyperTerminal window to establish a new connection
and the system will display the Connection Description dialog box.
Figure 5-2 Connection description of HyperTerminal
2) Input the name of the new connection and click <OK>. Then there pops up the
interface as shown in the following figure. Select the serial port to be used from the
“Connect using” drop down list.
Installation Manual
H3C S7502 Ethernet Switch Chapter 5 System Commissioning
5-3
Figure 5-3 Setting serial port for HyperTerminal connection
3) After selecting serial ports, click <OK>. The following interface will pop up for
setting serial port parameters. Set the bits per second to 9600, data bits to 8, parity
check to none, stop bits to 1, and flow control to none.
Figure 5-4 Setting serial port parameters
Installation Manual
H3C S7502 Ethernet Switch Chapter 5 System Commissioning
5-4
4) After setting serial port parameters, click <OK>. Then the system will enter the
HyperTerminal dialogue box as shown in the following figure.
Figure 5-5 HyperTerminal interface
In the above dialogue box, select the Properties icon to enter the properties window.
Click Settings to set the attributes (see the following figure). In this interface, select
terminal emulation mode VT100 and then click <OK>.
Installation Manual
H3C S7502 Ethernet Switch Chapter 5 System Commissioning
5-5
Figure 5-6 Setting terminal emulation mode in the property setting window
5.2 Power-on
5.2.1 Check before Power-on
Before powering on an Ethernet Switch, check that:
zThe switch has been mounted steadily.
zAll the cards have been correctly installed.
zAll the communication cables, fibers, power cables, and grounding cables have
been correctly connected.
zThe voltage of power supply meets the requirements on the switch.
zThe Console cable has been correctly connected. The computer or terminal for
configuration has been started and the terminal parameter settings have been
done.
Installation Manual
H3C S7502 Ethernet Switch Chapter 5 System Commissioning
5-6
Caution:
Before powering on the switch, confirm where the power switch of the equipment room
is located, so that you will be able to power off in case of accidence.
5.2.2 Power-on
zTurn on the power supply of the switch.
zPower on the switch.
5.2.3 Check after Power-on (Recommended)
You are recommended to check as follows after powering on the switch to ensure the
configurations thereafter.
zAfter a switch is powered on, the heat dissipation system starts working. You can
hear the noise as the fan rotates and feel air flow out from the vent.
zCheck if any system indicator on the SRPU indicates abnormal condition.
5.2.4 Starting the Interface
As the switch is started, the configuration terminal will yield the following output:
Starting......
RAM Line....OK
System is booting................
******************************************
* *
* H3C S7502 BOOTROM, Version 530 *
* *
******************************************
Copyright(c) 2004-2007 Hangzhou H3C Tech. Co., Ltd.
Creation date : Apr 20 2007, 14:48:52
CPU type : MPC8245
CPU Clock Speed : 300Mhz
BUS Clock Speed : 33Mhz
BOOT_FLASH type : M29W040B
Flash Size : 32MB
Memory Size : 256MB
S7502 main board self testing................................
SDRAM Data lines Selftest.................................OK!
SDRAM Address lines Selftest..............................OK!
Installation Manual
H3C S7502 Ethernet Switch Chapter 5 System Commissioning
5-7
SDRAM fast selftest.......................................OK!
Please check LEDs.....................LEDs selftest finished!
CPLD selftest.............................................OK!
The switch Mac address is .....................0000.0309.0004
Press Ctrl+B to enter Boot Menu... 0
Auto-booting...
Auto booting file is S7502.app
There are 4 files in this packet
SRPG app file <<srpu.app>> is...OK
Decompress Image...................................................
.......................................................OK!
Starting at 0x60000...
..........................................................................
................................ .........................................
................................................................. ........
..........................................................................
User interface Aux0/0 is available
Press ENTER to get started.
The displaying of the above indications indicates the completion of the switch
auto-booting.
Press <Enter> and you will get the following output. By this time, you can start
configuring the switch.
<H3C>
Note:
The S7502 provides a variety of command views. For the specific descriptions on the
configuration commands and command line interfaces, refer to H3C S7500 Series
Ethernet Switches Operation Manual and H3C S7500 Series Ethernet Switches
Command Manual.
Other manuals for S7502
7
Table of contents
Other H3C Network Router manuals
H3C
H3C MSR3600-28-X1 User manual
H3C
H3C SR6602 User manual
H3C
H3C MSR 5600 Operating and maintenance manual
H3C
H3C S3100 Series Installation instructions
H3C
H3C CR16000-M Operating and maintenance manual
H3C
H3C H3C S5100-SI User manual
H3C
H3C SR6616 Operating and maintenance manual
H3C
H3C CR16000-F Installation manual
H3C
H3C S5560-EI series User manual
H3C
H3C H3C S7500E-X Installation manual
H3C
H3C MSR810 User manual
H3C
H3C SR6602-X User manual
H3C
H3C S3100-52P Installation instructions
H3C
H3C MSR Series Installation manual
H3C
H3C MSR 5600 Operating and maintenance manual
H3C
H3C MSR 50 Series Manual
H3C
H3C SR6600 Series Installation guide
H3C
H3C H3C S7500E Series Installation manual
H3C
H3C MSR 30-16 User manual
H3C
H3C CR16000-F User manual
