H3C SR6616 Operating and maintenance manual

Installation accessories

No installation tools are provided with the router. Prepare them yourself as required.

设备不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。

Flathead screwdriver

一字螺丝刀

Phillips screwdriver

十字螺丝刀

Needle-nose pliers

尖嘴钳

ESD wrist strap

防静电腕带

Diagonal pliers

斜口钳

BOM: 3104A12P

Tool list

H3C SR6616 Routers Installation Quick Start-6PW124

H3C SR6616 -6PW124

Attaching the cable management bracket to the router

Grounding cable

接地线

Cage nut

浮动螺母

M6 rack screw

M6机柜螺钉

M4 mounting

bracket screw

M4挂耳螺钉

Mounting brackets

挂耳

Cable management

bracket

走线架

Releasable cable tie

可拆卸式扎带

Wear an ESD wrist strap, and make sure the wrist strap makes good skin contact and

is reliably Grounded. 操作者需佩戴防静电腕带，确保防静电腕带与皮肤良好接触，并确

认防静电腕带已经良好接地。

Wire-stripping pliers

剥线钳

Attach the cable management bracket to the router before you mount the router in a rack.

设备需要单独安装走线架，设备安装到机柜之前，需要用螺丝钉将走线架固定到设备上。

Attaching mounting brackets to the router

Attach mounting brackets to the router before you mount the router in a rack.

安装设备到机柜前，需要先将前挂耳分别固定到设备前面板的左右两侧。

Mounting the router in a rack

Connecting the grounding cable

Correctly connecting the grounding cable is crucial to lightning protection and EMI

protection. To guarantee the grounding effect, use the grounding cable provided with

the router for grounding. 设备地线的正确连接是设备防雷、防干扰的重要保障，请使用

设备随机提供的保护地线正确接地。

To ground the router when mounted in a rack:

1. Connect the building grounding facility to the grounding strip on the rack. Make sure the

rack is reliably grounded.

2. Use the grounding cable provided with the router to connect the router to the grounding

strip on the rack.

设备安装在机柜时，要求机柜已经良好接地，首先需将楼宇接地保护装置与机柜接地排相连，

然后使用接地线将设备与机柜接地排相连。

You can rack-mount the router by using mounting brackets and a rack shelf or

mounting brackets and slide rails. Choose the rack mounting method as required.

This section describes how to rack-mount the router by using mounting brackets and

a rack shelf.

设备安装到机柜时，可以使用挂耳和托盘配合安装或者挂耳和滑道配合安装，请根据

实际应用场景选择，本节以挂耳和托盘配合安装举例。

No rack shelf or slide rail is provided with the router. Prepare one yourself.

设备不随机提供托盘或滑道，请用户自备。

Installing MPUs/switching fabric modules/service modules

/ /

Installing an MPU carrier

安装主控板托板

The router supports dual MPUs.

Installing an RPE-X1, RPE-X3, RPE-X5,

or RPE-X5E MPU 安装RPE-X1、RPE-

X3、RPE-X5和RPE-X5E主控板

!The router supports hot swapping of MPUs, switching fabric modules, and service modules.

主控板、网板、业务板支持热插拔。

Installing a service module

安装业务板

Installing a switching fabric module

安装网板

Before installi n g an RPE-X1, RPE-X3, RPE-X5, o r RPE-X5E MPU, install a

compatible carrier in the MPU slot.

The router supports dual MPUs. Do not hot swap the MPU when only one MPU is

installed on the router.

安装RPE-X1、RPE-X3、RPE-X5和RPE-X5E主控板前需要先安装对应的托板。

设备支持双主控，配置单主控时，不允许热插拔主控板。

Installing an air deflector

安装FIP-660挡风假面板

If the service module slots adjacent to an FIP-660 are empty, install an air deflector in

either of the slots.

安装FIP-660时，如果FIP-660相邻的业务板槽位空闲，则必须选择一相邻的空闲业务板

插槽安装标配的挡风假面板。

Install an RSE-X1, MCP-X1, or MCP-X2

MPU

安装RSE-X1/MCP-X1/X2主控板或主控

处理引擎

Push the power module slowly into the slot along the guide rails.

将电源模块沿着插槽导轨，水平缓慢的推进电源插槽。

Connecting an AC power cord 连接交流电源线

Connecting the power cord for a PSR1200-D DC power module

连接PSR1200-D直流电源模块电源线

To install two power modules for the router, make sure they are the same model.

设备安装多电源模块时，请保证两块电源模块的型号相同。

Installing power modules

The router supports the PSR1200-A and PSR1200-D power modules. 设备支持型号

PSR1200-A、PSR1200-D的电源模块。

Install a minimum of one power module for the router. To ensure good ventilation and

prevent dust from entering the chassis, install a filler panel in each unused power

module slot. 为保证设备的正常运行，请至少安装一块电源模块，没有安装电源模块的

槽位，请及时安装假面板，以保证设备的良好通风散热并防止灰尘进入设备。

The information in this document is subject to change without notice.

本文档中的信息如有更改，恕不另行通知

如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com

This quick start is specific to the following device models:

本手册适用的设备型号如下：

List of devices

Product code

Model (marked on the front panel)

RT-SR6616-H3

H3C SR6616

Connecting power cords

Before connecting a power cord, make sure the router is reliably grounded.

在连接电源线前，需保证设备已正确接地。

To avoid bodily injury, connect the power cord first to the router and then to the power

source. 在连接电源线时，先完成电源线与设备侧的连接，再进行电源线与机房

供电系统的连接，以免造成人身伤害。

Other manuals for SR6616

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview