GW Instek PPH-1503D User manual

Programmable High Precision

Dual Output DC Power Supply

PPH-1503D/PPH-1506D/ PPH-1510D

User Manual

GW INSTEK PART NO. 82PH-1503DED1

ISO-9001 CERTIFIED MANUFACTURER

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS .................................................. 5

OVERVIEW .................................................................... 10

Introduction ................................................... 10

Key Features ................................................... 12

Operating Principals ...................................... 14

Front Panel ..................................................... 16

Rear Panel ...................................................... 22

Constant Voltage/Constant Current

Crossover Characteristics ............................... 24

GETTING STARTED........................................................ 25

Start Up.......................................................... 25

Load and DVM Connection............................. 26

Turning the Output On/Off ............................ 28

MAIN MENU OVERVIEW................................................ 29

Function Description ...................................... 30

BASIC OPERATION ........................................................ 32

Source Function ............................................. 32

DVM............................................................... 43

Pulse Current Measurement ........................... 45

Long integration ............................................. 51

Battery simulation function ............................ 56

Current Sink Function..................................... 57

External Relay Control .................................... 59

Sequence Function ......................................... 62

SAVE/RECALL ................................................................ 64

Restore Factory Default Settings..................... 67

The Factory Default Settings .......................... 67

PPH-1503D/1506D/1510D User Manual

SYSTEM SETTINGS ........................................................ 69

System Information ........................................ 69

Utility Settings ............................................... 70

Firmware Upgrading....................................... 72

System Real Time Clock Setting ..................... 73

Description of Using Flash Drive .................... 74

REMOTE CONTROL ....................................................... 79

Remote Control .............................................. 79

Command Syntax............................................ 86

Command List ................................................ 90

Command Details........................................... 95

SCPI Status Registers SCPI........................... 130

Errors ........................................................... 138

APPENDIX ....................................................................142

Replacing the Fuse ....................................... 142

Battery Replacement..................................... 143

Specifications ............................................... 144

Optional Accessories.................................... 146

Declaration of Conformity ............................ 147

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

PPH-1503D/1506D/1510D User Manual

Safety Guidelines

General

Guideline

CAUTION

 Do not place any heavy object on the unit.

 Avoid severe impact or rough handling that

leads to damaging the unit.

 Do not discharge static electricity to the unit.

 Do not block the cooling fan opening.

 Do not perform measurements on circuits that

are directly connected to mains power.

 Do not disassemble the PPH unless you are

qualified.

(Measurement categories) EN 61010-1:2010 specifies the

measurement categories and their requirements as follows. The

PPH-1503D/1506D /1510D falls under category I.

 Measurement category IV is for measurement performed at the

source of low-voltage installation.

 Measurement category III is for measurement performed in the

building installation.

 Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

 Measurement category I is for measurements performed on

circuits not directly connected to Mains.

Power Supply

WARNING

 AC Input voltage range: 90VAC~264VAC

 Frequency: 50Hz/60Hz

 To avoid electrical shock connect the protective

grounding conductor of the AC power cord to

an earth ground.

SAFETY INSTRUCTIONS

Fuse

WARNING

 Fuse type: T2.0A/250V（PPH-1503D）

T2.5A/250V PPH-1506D/1510D

 To prevent fire, replace the fuse only with the

specified type and rating.

 Disconnect the power cord before replacing the

fuse.

 Make sure the cause of fuse blowout is fixed

before replacing the fuse.

Cleaning the

power supply

 Disconnect the power cord before cleaning the

oscilloscope.

 Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid

into the oscilloscope.

 Do not use chemicals containing harsh products

such as benzene, toluene, xylene, and acetone.

Operation

Environment

 Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

 Relative Humidity: < 80%

 Altitude: < 2000m

 Temperature: 0°C to 40°C

(Pollution Degree) EN 61010-1:2010 specifies pollution degrees and

their requirements as follows. The PPH-1503D/1506D/1510D falls

under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

 Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

 Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

 Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

PPH-1503D/1506D/1510D User Manual

Storage

environment

 Location: Indoor

 Relative Humidity: < 70%

 Temperature: -10°C to 70°C

SAFETY INSTRUCTIONS

Power cord for the United Kingdom

When using the power supply in the United Kingdom, make sure

the power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with the

coloured marking identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth

terminal marked with either the letter E, the earth symbol or coloured

Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal which is

marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal

marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact

the supplier.

This cable/appliance should be protected by a suitably rated and approved

HBC mains fuse: refer to the rating information on the equipment and/or

user instructions for details. As a guide, a cable of 0.75mm2should be

protected by a 3A or 5A fuse. Larger conductors would normally require

13A types, depending on the connection method used.

Any exposed wiring from a cable, plug or connection that is engaged in a

live socket is extremely hazardous. If a cable or plug is deemed hazardous,

turn off the mains power and remove the cable, any fuses and fuse

assemblies. All hazardous wiring must be immediately destroyed and

replaced in accordance to the above standard.

PPH-1503D/1506D/1510D User Manual

OVERVIEW

This chapter contains a brief introduction to PPH-

1503D/1506D/1510D, the main features, as well

as an overview of the front and rear panel. Use the

Getting Started chapter on page 25 to start up

instructions and how to setup the appropriate

operation environment.

Introduction

Overview

The PPH-1503D/1506D /1510Dis a high-precision,

compact, dual output, multifunction,

programmable DC power supply with flexible

operating configurations. In addition to the basic

power supply functionality, it is also able to

measure pulse current, the average current over

long periods of time and other functions such as

battery simulation.

The PPH-1503D/1506D/1510D is designed for

testing the power consumption of battery powered

wireless communication devices (e.g. cell phones).

Such devices often have large load variations

within a short time span. The high precision

power supply has excellent voltage stability

during pulsed loads and is capable of

simultaneously measuring the pulse current, even

for very short pulses. In addition, the power

supply is able to sink current, allowing it to

simulate the characterics of a discharged

rechargeable battery for testing chargers and

charge control circuits.

This manual suits for next models

Table of contents

Other GW Instek Power Supply manuals

GW Instek

GW Instek GPE-1326 Series User manual

GW Instek

GW Instek PSM-2010 User manual

GW Instek

GW Instek PSW 30-72 Owner's manual

GW Instek

GW Instek GPP-3323 User manual

GW Instek

GW Instek PSP-603 User manual

GW Instek

GW Instek ASD Series User manual

GW Instek

GW Instek PSP-603 User manual

GW Instek

GW Instek SPS-1230 User manual

GW Instek

GW Instek ASD Series User manual

GW Instek

GW Instek PSU 60-25 User manual

GW Instek

GW Instek PSP-603 User manual

GW Instek

GW Instek PSU Series User manual

GW Instek

GW Instek SPS-1230 User manual

GW Instek

GW Instek GPD-303S Series User manual

GW Instek

GW Instek GPD-2303S User manual

GW Instek

GW Instek PSP-603 User manual

GW Instek

GW Instek SPS Series User manual

GW Instek

GW Instek PSB-1400L User manual

GW Instek

GW Instek GPS-1830 User manual

GW Instek

GW Instek PSH series User manual

GW Instek

GW Instek PST Series Operating and maintenance manual

GW Instek

GW Instek GPS-2303 User manual

GW Instek

GW Instek ASR-2000 Series User manual

GW Instek

GW Instek GCP-206P User manual

Popular Power Supply manuals by other brands

Monacor

Monacor PS-12CCD instruction manual

VOLTIMA

VOLTIMA MagicBox 15 Installation and operating instructions

Agilent Technologies

Agilent Technologies 6032A Service manual

Miller

Miller Auto Deltaweld 452 owner's manual

BCP

BCP PUOUBK How to install

HC 2210 manual

Puls

Puls CT5.241 installation manual

OCZ

OCZ ZX1250W Technical specifications

iseg

iseg ECH 238 manual

Power

Power XXL A Series instruction manual

Agilent Technologies

Agilent Technologies 6631B Service manual

Renogy

Renogy PHOENIX 300 user guide

HP 6200B Operating and service manual

Epson

Epson Stylus Scan 2500 Product information sheet

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 manual

Puls

Puls MiniLine ML50.100 instruction manual

Puls

Puls AS-Interface SLA4.100 installation manual

Kenwood

Kenwood PS-60 instruction manual