Grizzly H6193 User manual
Introduction
No load speed is 22,000 RPM and collet size is 1⁄4".
Requires a maximum of 90 PSI with a minimum of
3 CFM compressor capacity. Air inlet is 1⁄4" and air
exhaust is in the front. Weighs 1.2 lbs.
Inventory
A. Die Grinder ................................................. 1
B. Wrenches ................................................... 2
Operation
Insert your 1⁄4" shank tool into the collet. Using the
two wrenches, secure tool by tightening the collet
against the spindle.
MODEL H6193
1⁄4" INDUSTRIAL
DIE GRINDER
INSTRUCTION SHEET
Figure 1. Model H6193.
Figure 2. Lubricating directly into air fitting.
If you need help with your new pneumatic tool,
call our Tech Support at: (570) 546-9663.
COPYRIGHT © FEBRUARY, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#PC8031 PRINTED IN TAIWAN
Die Grinder MUST have 3-4 drops of oil directly
dropped into the air fitting before each use as
shown in Figure 2.
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service!
EYE/EAR INJURY HAZARD!
Wear safety glasses and
hearing protection during
use of this tool!
RESPIRATORY HAZARD!
Grinding produces fine
dust. Wear the appropriate
protection during use!
EXPLOSION HAZARD!
Never exceed 90 PSI! Always
use accessories with correct
speed rating.
H6193 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH6193001 HOUSING COVER 13 PH6193013 ROTOR BLADE
2 PH6193002 HOUSING 14 PH6193014 ROTOR
3 PH6193003 THROTTLE LEVER 15 PH6193015 CYLINDER
4 PH6193004 LEVER PIN 16 PH6193016 BEARING SPACER
5 PH6193005 VALVE PIN 17 PH6193017 FRONT END PLATE
6 PH6193006 VALVE 18 PH6193018 BEARING
7 PH6193007 COMPRESSION SPRING 19 PH6193019 SPINDLE
8 PH6193008 O-RING 20 PH6193020 RETAINER
9 PH6193009 VALVE CAP 21 PH6193021 HOUSING CAP
10 PH6193010 BALL BEARING 22 PH6193022 COLLET
11 PH6193011 REAR END PLATE 23 PH6193023 WRENCH 12MM
12 PH6193012 PIN 24 PH6193024 WRENCH 11MM
Other Grizzly Grinder manuals
Grizzly
Grizzly G2790 User manual
Grizzly
Grizzly G0686 User manual
Grizzly
Grizzly Grinding Jig G4570 User manual
Grizzly
Grizzly G7298 User manual
Grizzly
Grizzly H7757 User manual
Grizzly
Grizzly G0688 User manual
Grizzly
Grizzly G0596 User manual
Grizzly
Grizzly G2790 User manual
Grizzly
Grizzly H8126 User manual
Grizzly
Grizzly H4380 User manual
Grizzly
Grizzly T24463 User manual
Grizzly
Grizzly H8125 User manual
Grizzly
Grizzly G1806 User manual
Grizzly
Grizzly G0897 User manual
Grizzly
Grizzly H8212 User manual
Grizzly
Grizzly G9928 User manual
Grizzly
Grizzly H7762 User manual
Grizzly
Grizzly G1806 User manual
Grizzly
Grizzly G1036 User manual
Grizzly
Grizzly t10493 User manual
