Grizzly H0588 User manual
Introduction
Angle Die Grinders are excellent for reaching
sideways into areas that are relatively confined.
No-load speed is 18,000 RPM and collet size is
1⁄4". Requires 90 PSI with 4 CFM of compressor
capacity. Air inlet is 1⁄4" and air exhaust is in the
rear. Weighs just over 1 lb.
Inventory
A. Die Grinder ................................................. 1
B. Flat Wrench 17mm ..................................... 1
C. Flat Wrench 12mm ..................................... 1
Operation
Tool requires 90 PSI to operate correctly.
To improve tool lifespan, use a filter/lubricator/
regulator as shown in Figure 2. Otherwise, lubri-
cate daily with a couple drops of pneumatic tool oil
directly into the air fitting as shown in Figure 3.
MODEL H0588
1⁄4" ANGLE DIE GRINDER
INSTRUCTION SHEET
Figure 1. Model H0588.
Figure 3. Lubricating directly into air fitting.
If you need help with your new pneumatic tool,
call our Tech Support at: (570) 546-9663.
COPYRIGHT © FEBRUARY, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#KM7957 PRINTED IN TAIWAN
EYE INJURY HAZARD!
Always wear safety glasses
when using this tool to
prevent serious personal
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service.
EXPLOSION HAZARD!
Never exceed 120 PSI.
Quick
Connector
Quick
Coupler
Air Hose Quick
Coupler
Quick
Connector
Lubricator
Filter
Regulator
Air
Compressor
Your
Tool
Figure 2. Installing your tool.
H0588 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH0588001 MOTOR HOUSING 20 PH0588020 MOTOR CLAMP
2 PH0588002 THROTTLE VALVE 21 PH0588021 HOUSING CAP
3 PH0588003 THROTTLE VALVE SPRING 22 PH0588022 ANGLE HEAD HOUSING
4 PH0588004 AIR REGULATOR 23 PH0588023 REAR SPINDLE BALL BEARING
5 PH0588005 O-RING 24 PH0588024 SPINDLE GEAR
6 PH0588006 O-RING 25 PH0588025 FRONT SPINDLE BALL BEARING
7 PH0588007 VALVE SCREW 26 PH0588026 WOODRUFF KEY
8 PH0588008 THROTTLE LEVER 27 PH0588027 SPINDLE
9 PH0588009 THROTTLE LEVER PIN 28 PH0588028 CLAMP NUT
10 PH0588010 REAR ROTOR BALL BEARING 29 PH0588029 COLLET
11 PH0588011 REAR END PLATE 30 PH0588030 COLLET NUT
12 PH0588012 BALL 31 PH0588031 THROTTLE VALVE BUSHING
13 PH0588013 ROTOR COLLAR 32 PH0588032 O-RING
14 PH0588014 CULINDER 33 PH0588033 FLAT WRENCH
15 PH0588015 ROTOR 34 PH0588034 EXHAUST SLEEVE
16 PH0588016 ROTOR BLADE 35 PH0588035 AIR INLET
17 PH0588017 FRONT END PALTE 36 PH0588036 FLAT WRENCH
18 PH0588018 FRONT ROTOR BALL BEARING 37 PH0588037 BALL
19 PH0588019 PINION GEAR
Other Grizzly Grinder manuals
Grizzly
Grizzly G5963 User manual
Grizzly
Grizzly H8124 User manual
Grizzly
Grizzly H6156 Quick start guide
Grizzly
Grizzly T10875 User manual
Grizzly
Grizzly H8125 User manual
Grizzly
Grizzly G0597 User manual
Grizzly
Grizzly G0596-99 User manual
Grizzly
Grizzly T10010 User manual
Grizzly
Grizzly T10010ANV User manual
Grizzly
Grizzly G1036 User manual
Grizzly
Grizzly H7758/H7759 User manual
Grizzly
Grizzly H6155 User manual
Grizzly
Grizzly T28523 User manual
Grizzly
Grizzly H8126 User manual
Grizzly
Grizzly G5968/9 User manual
Grizzly
Grizzly G0686 User manual
Grizzly
Grizzly H6249 User manual
Grizzly
Grizzly G8183 User manual
Grizzly
Grizzly H4380 User manual
Grizzly
Grizzly T10023 User manual
