Graco Ti13498a Operating instructions

IMPORTANT SAFETY INSTRUCTIONS

Read all warnings and instructions in this manual.

Save these instructions.

313558E rev.a

Ultra

Platinum Sprayers

- For Portable Airless Spraying of Architectural Coatings and Paints -

Repair

ti13498a

695/795

ti13630a

1095/MARK V

Table of Contents

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Component Identification . . . . . . . . . . . . . . . . . . . . . . 7

General Repair Information . . . . . . . . . . . . . . . . . . . . . 8

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . 8

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Mechanical/Fluid Flow . . . . . . . . . . . . . . . . . . . . . . 10

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

240 Vac and 110 Vac Motor Control Board . . . . . . 19

240 Vac Filter Board . . . . . . . . . . . . . . . . . . . . . . . 20

Pressure Adjust Potentiometer . . . . . . . . . . . . . . . 22

Pressure Control Transducer . . . . . . . . . . . . . . . . . 24

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Drive and Bearing Housing Replacement . . . . . . . . 27

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Motor Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Displacement Pump Replacement for 695/795 . . . . 31

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Displacement Pump Replacement 1095/Mark V . . . 33

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Hose Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Smart Control-E Board Replacement . . . . . . . . . . . . 38

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

AutoClean Reed Switch Replacement . . . . . . . . . . . 39

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

E-Control Battery Replacement . . . . . . . . . . . . . . . . . 40

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . 42

Models

Vac Model Hi-Boy

240 Europe

695 257034

795 257037

1095 257040

Mark V 257043

240 Europe

Multi-Cord

695 257035

795 257038

1095 257041

Mark V 257044

110 UK

695 257036

795 257039

1095 257042

Mark V 257045

Warnings

The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation

point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to

these warnings. Additional, product-specific warnings may be found throughout the body of this manual where appli-

cable.

Grounding Instructions

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock

by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with

an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

WARNING

GROUNDING

• Improper installation of the grounding plug is able to result in a risk of electric shock.

• When repair or replacement of the cord or plug is required, do not connect the grounding wire to

either flat blade terminal.

• The wire with insulation having an outer surface that is green with or without yellow stripes is the

grounding wire.

• Check with a qualified electrician or serviceman when the grounding instructions are not completely

understood, or when in doubt as to whether the product is properly grounded.

• Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qual-

ified electrician.

• This product is for use on a nominal 120V circuit and has a grounding plug similar to the plug illus-

trated in the figure below.

• Only connect the product to an outlet having the same configuration as the plug.

• Do not use an adapter with this product.

Extension Cords:

• Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that

accepts the plug on the product.

• Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG

(2.5 mm2) minimum to carry the current that the product draws.

• An undersized cord results in a drop in line voltage and loss of power and overheating.

ti9164a

Warnings

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent

fire and explosion:

• Do not spray flammable or combustible materials near an open flame or sources of ignition such as

cigarettes, motors, and electrical equipment.

• Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity

creates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray sys-

tem, including the pump, hose assembly, spray gun, and objects in and around the spray area shall

be properly grounded to protect against static discharge and sparks. Use Graco conductive or

grounded high-pressure airless paint sprayer hoses.

• Verify that all containers and collection systems are grounded to prevent static discharge.

• Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.

• Do not use a paint or a solvent containing halogenated hydrocarbons.

• Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep

pump assembly in a well ventilated area. Do not spray pump assembly.

• Do not smoke in the spray area.

• Do not operate light switches, engines, or similar spark producing products in the spray area.

• Keep area clean and free of paint or solvent containers, rags, and other flammable materials.

• Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets

(MSDS) and container labels provided with the paints and solvents. Follow the paint and solvents

manufacturer’s safety instructions.

• Fire extinguisher equipment shall be present and working.

• Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or

cleaning, keep sprayer at least 20 feet (6 m) away from explosive vapors.

SKIN INJECTION HAZARD

• Do not aim the gun at, or spray any person or animal.

• Keep hands and other body parts away from the discharge. For example, do not try to stop leaks

with any part of the body.

• Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.

• Use Graco nozzle tips.

• Use caution when cleaning and changing nozzle tips. in the case where the nozzle tip clogs while

spraying, follow the Pressure Relief Procedure for turning off the unit and relieving the pressure

before removing the nozzle tip to clean.

• Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn

off the unit and follow the Pressure Relief Procedure for turning off the unit.

• High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event

that injection occurs, get immediate surgical treatment.

• Check hoses and parts for signs of damage. Replace any damaged hoses or parts.

• This system is capable of producing 3300 psi. Use Graco replacement parts or accessories that are

rated a minimum of 3300 psi.

• Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.

• Verify that all connections are secure before operating the unit.

• Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls.

WARNING

Warnings

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Always wear appropriate gloves, eye protection, and a respirator or mask when painting.

• Do not operate or spray near children. Keep children away from equipment at all times.

• Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.

• Stay alert and watch what you are doing.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not kink or over-bend the hose.

• Do not expose the hose to temperatures or to pressures in excess of those specified by Graco.

• Do not use the hose as a strength member to pull or lift the equipment.

ELECTRIC SHOCK HAZARD

Improper grounding, setup, or usage of the system can cause electric shock.

• Turn off and disconnect power cord before servicing equipment.

• Use only grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on sprayer and extension cords.

• Do not expose to rain. Store indoors.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1, 1, 1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids

containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical

reaction and equipment rupture, and result in death, serious injury, and property damage.

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating

area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic

fumes, burns, and hearing loss. This equipment includes but is not limited to:

• Protective eye wear

• Clothing and respirator as recommended by the fluid and solvent manufacturer

•Gloves

• Hearing protection

WARNING

Component Identification

5. 6. 7. 8.

10.

11.

12.

13.14.

ti13668a

English

1 Premium Digital Display

2 ON/OFF Switch

3 Pressure Control / E-Control

4 Prime / Spray Valve

5 Filter

6AutoClean2™

7 Siphon Tube

8Pump

9Bearing Housing / ProConnect™

10 Fluid Outlet

11 Drain Tube

12 Trigger Lock

13 Model/Serial Tag

14 WatchDog™Switch (not Mark V)

General Repair Information

Pressure Relief Procedure

System pressure must be manually relieved to prevent

system from starting or spraying accidentally. Fluid un-

der high pressure can be injected through skin and

cause serious injury. To reduce risk of injury from injec-

tion, splashing fluid, or moving parts, follow Pressure Re-

lief Procedure whenever you:

• are instructed to relieve pressure

• stop spraying

• check or service any system equipment

• install or clean spray tip

1. Turn pressure control knob to zero.

2. Turn ON/OFF switch to OFF.

3. Unplug power supply cord.

4. Hold metal part of gun firmly to grounded metal pail.

Trigger gun to relieve pressure.

5. Lock gun safety latch.

6. Open prime valve. Leave prime valve open until

ready to spray again.

If suspected that spray tip or hose is completely

clogged, or that pressure has not been fully relieved

after following steps above, VERY SLOWLY loosen

tip guard retaining nut or hose end coupling to re-

lieve pressure gradually, then loosen completely.

Then clear tip or hose obstruction.

1. Keep all screws, nuts, washers, gaskets, and electri-

cal fittings removed during repair procedures. These

parts are not normally provided with replacement

assemblies.

To reduce risk of serious injury, including electric shock,

do not touch moving or electrical parts with fingers or

tools while testing repair. Shut off and unplug sprayer

when inspection is complete. Install all covers, guards,

gaskets, screws, washers and shroud before operating

sprayer.

2. Test repair after problem is corrected.

3. If sprayer does not operate properly, review repair

procedure to verify procedure was done correctly. If

necessary, see Troubleshooting, page 10, for other

possible solutions.

NOTICE

To reduce risk of pressure control malfunction:

• Use needle-nose pliers to disconnect wire. Never

pull on wire, pull on connector.

• Mate wire connectors properly. Center flat blade of

insulated male connector in female connector.

• Route wires carefully to avoid interference with

other connections of pressure control. Do not

pinch wires between cover and control box.

Grounding

Improper installation or alteration of grounding plug re-

sults in risk of electric shock, fire or explosion that could

cause serious injury or death.

1. Ultra Max II 695, 795 and 1095 100-200 Vac models

require a 50/60 Hz, 15A circuit with a grounding

receptacle. Ultra Max II 1595/Mark V 120 Vac mod-

els require a 50/60 Hz 20A circuit with a grounding

receptacle; 220-240 Vac models require a 50/60 Hz,

10A circuit with a grounding receptacle.

2. Do not alter ground prong or use adapter.

3. 120 Vac: A 12 AWG, 3 wires with grounding prong,

300 ft (90 m) extension cord may be used. 220-240

Vac: You may use a 3-wire, 1.0 mm (12 AWG) (mini-

mum) extension cord up to 90 m long. Long lengths

reduce sprayer performance.

ti2810a

Troubleshooting

Mechanical/Fluid Flow

Relieve pressure; page 8.

TYPE OF PROBLEM

WHAT TO CHECK

If check is OK, go to next check

WHAT TO DO

When check is not OK, refer to this column

E=XX is displayed 1. Fault condition exists 1. Determine fault correction from table,

page 12.

False tripping of WatchDog

system. EMPTY is dis-

played. Pump does not run.

1. Operating conditions out of

WatchDog parameters. Pump

output is low, see below.

1. Turn pressure down. Refer to operation

manual for adjusting. Operate without

WatchDog active; see operation manual.

Pump output is low 1. Spray tip worn 1. Follow Pressure Relief procedure Warn-

ing, then replace tip. See your separate

gun or tip manual.

2. Spray tip clogged 2. Relieve pressure. Check and clean spray

tip.

3. Paint supply 3. Refill and reprime pump.

4. Intake strainer clogged 4. Remove and clean, then reinstall

5. Intake valve ball and piston ball

are not seating properly

5. Remove intake valve and clean. Check

balls and seats for nicks; replace if neces-

sary; see pump manual 310643 or

310894. Strain paint before using to

remove particles that could clog pump.

6. Suction hose connections 6. Tighten any loose connections. Check for

missing or damaged seals.

7. Fluid filter, tip filter, or tip is

clogged or dirty.

7. Clean filter; see operation manual.

8. Prime valve leaking 8. Relieve pressure. Repair prime valve.

9. Verify pump does not continue to

stroke when gun trigger is

released. (Prime valve not leak-

ing.)

9. Service pump; see pump manual 310643

or 310894.

10. Leaking around throat packing

nut which may indicate worn or

damaged packings.

10. Replace packings; see pump manual. Also

check piston valve seat for hardened paint

or nicks and replace if necessary. Tighten

packing nut/wet-cup.

11. Pump rod damage 11. Repair pump. See pump manual 310643

or 310894.

12. Low stall pressure 12. Turn pressure knob fully clockwise. Make

sure pressure control knob is properly

installed to allow full clockwise position. If

problem persists, replace pressure trans-

ducer.

13. Piston packings are worn or

damaged

13. Replace packings; see pump manual

310643 or 310894.

This manual suits for next models

Table of contents

Other Graco Paint Sprayer manuals

Graco

Graco 233001 Operation manual

Graco

Graco GMax 5900 Instruction Manual

Graco

Graco GUSMER D Series User manual

Graco

Graco 288776 Parts list manual

Graco

Graco SaniSpray HP 20 User manual

Graco

Graco EM 390 User manual

Graco

Graco 240054 Operation manual

Graco

Graco T-Max 405 A Series Operating instructions

Graco

Graco 455st Pro Instruction Manual

Graco

Graco M73380 Operation manual

Graco

Graco 311365G Operating instructions

Graco

Graco TexSpray 248091 Guide

Graco

Graco Xtreme NXT User manual

Graco

Graco Line Lazer 3500 Operation manual

Graco

Graco 237-296 Operation manual

Graco

Graco FOAM-CAT 200 Operation manual

Graco

Graco 237–428 Operation manual

Graco

Graco Series A Operation manual

Graco

Graco GMAX 258731 User manual

Graco

Graco 17C305 Guide

Graco

Graco Magnum X5 Use and care manual

Graco

Graco 312145D Operation manual

Graco

Graco 237-421 Operation manual

Graco

Graco Inline HD 245820 Guide

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual

Graco ti13498a Operating instructions

Popular Paint Sprayer manuals by other brands