Graco T-MAX 506 Manual

T-MAX™506/657

www.graco.com

STARTUP

STARTUP Spray with Air <= 1.5 mm

Fill material hopper

with pre-mixed texture

material.

Turn pressure control

knop until a steady

stream flows from

material hose. Turn pump OFF.

Turn applicator OFF,

Turn ON/OFF switch

to ON

Lossen nut on bottom

of pump

two to three turns to

relieve pressure

Turn pressure control

to maximum. To spray,

aim applicator with a

distance of 0,5 m to the

wall and open applictor.

To clean a tip clog, turn

applicator OFF, turn Tip 180°

to Clean position, aim in waste

area, turn applicator ON, when

clog clears, turn applictor OFF

and tip in spray postion.

Turn pressure

control off (0).

Point applicator

into hopper.

Turn applicator ON.

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure Relief

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure

Relief

Use different tip size

for different flow

Install filter and tip

extension.

Connect applicator

to material hose.

Add water if thinning is

required. Mix thoroughly.

HDA531

HDA535

HDA541

HDA545

HDA651

HDA661

HDA671

mc03 m

Spray without Air < .25 mm

Srew tip assembley

onto applicator

Fill material hopper with

mixed texture material.

Place material hose in Hopper turn ON/OFF switch to ON Turn

control in the “green” segment, allow material to circulate 30 sec.

Turn pump control to

shut pump off

Screw air hose and valve to applicator.

Connect material hose to gun kit

Turn applicator valve OFF.

Install air nozzle.

Hold applicator over

material hopper and turn

applicator ON.

Turn air compressor ON. Turn pump

control in the “green” area, until

desired material rate is achieved.

Regulate the air valve to

get a good atomization.

To stop spraying,

turn applicator OFF

Quick Operator’s Guide

SETUP

This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing

fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.

* check the Graco operations manual delivered with the unit for more details.

WARNING

Turn pump control off (0).

Connect power cord.Connect pump module to hopper cart.

Remove pump plug.

Connect material hose to pump outlet.

PRESSURE RELIEF PROCESS

Turn pump control counter clockwise,

to shut pump off.

Close applictor after pressure release,

close air valve

Scrape material remaining in

hopper into pump to be pumped

from sprayer.

Rotate pump control to

(0) to shut pump off.

Shut OFF air compressor if spraying with air.

Remove applicator from material hose.

Clean applicator.

Rotate pump control

clockwise to start pump.

Rotate pump control to (0) to

shut pump off.

Clean applicator, spray tips and

guard with brush.ON/OFF switch to OFF

Turn pump control

clockwise and pump

unused texture material

from material hopper

and hose.

Run pump until

cleaning ball exits

material hose.Save

cleaning ball. Repeat

it till the water that

comes out is clear.

Insert wet cleaning ball into pump.

Connect material hose to pump outlet.

Clean hardened material

from applicator nozzles

with air nozzle cleaner.

Remove drain plug from Hopper

Clean hopper with water, brush

and sponge, install drain plug. fill

hopper 1/3 with clear water.

GRACO DISTRIBUTION BVBA Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777

www.graco.com

Graco is certified ISO 9001.

All information, illustrations, and specifications in this document are based on the latest product information

available at the time of publication. The right is reserved to make changes at any time without notice.

CHOOSE THE RIGHT TIP (HDA-XXX)

CLEANUP

XTRA LIGHT LIGHT MEDIUM HEAVY

HDA531 HDA541 HDA651 HDA671

HDA535 HDA545 HDA661 -

VERY FINE - 3MM FINE - 4MM MEDIUM - 6MM MEDIUM HEAVY - 8MM HEAVY - 10MM

248888 248524 248525 248526 248527

Other manuals for T-MAX 506

This manual suits for next models

Other Graco Paint Sprayer manuals

Graco

Graco Monark 236-065 User manual

Graco

Graco Hydra-Spray B Series User manual

Graco

Graco 231-351 Operation manual

Graco

Graco Pro Xp 24N319 User manual

Graco

Graco 695 ULTRA MAX lIl Instruction Manual

Graco

Graco EasyMax WP 258849 User manual

Graco

Graco AirPro 313516C User manual

Graco

Graco 258864 Instruction Manual

Graco

Graco TexSpray 234113 Instruction Manual

Graco

Graco 25T804 Guide

Graco

Graco 258850 User manual

Graco

Graco ULTRA R MAX 695 309067 Operation manual

Graco

Graco 238-258 Operation manual

Graco

Graco Finishpro 390 User manual

Graco

Graco Inline HD 245820 Operation manual

Graco

Graco Series E Operation manual

Graco

Graco Series A Operating instructions

Graco

Graco AA 2000 Datasheet

Graco

Graco 16N664 User manual

Graco

Graco Merkur G10W09 Parts list manual

Graco

Graco 311001C Datasheet

Graco

Graco Spray Station User manual

Graco

Graco ProShot 258865 User manual

Graco

Graco LP 555 Use and care manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual