Graco 25D496 User manual

Read Operation manual 3A5725 for complete instructions and warnings.

This guide is not a substitute for reading and understanding all operation manuals and warning labels supplied

with the equipment. It is important that you read and understand all warnings and instructions before operating

this equipment.

Follow the pressure relief procedure

and wear protective equipment including but not limited to protective eye wear.

RUPTURE HAZARD: Over-pressurizing the hopper can result in rupture. To avoid injury, only pressurize hopper

by connecting air supply tube to barbs on hopper and gun.

FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY, AMPUTATION OR DEATH.

COMPONENT IDENTIFICATION - 25D496

A. Material Flow Regulator: Pressurizes

the material hopper and adjusts material

flow. Turn counterclockwise to decrease

flow; turn clockwise to increase flow. Push

down to lock; pull up to unlock.

B. Needle Travel Adjustment Knob:

Adjusts the positions of the gun needle in

relation to the spray tip. Turn clockwise to

limit needle travel and reduce material

flow; turn counterclockwise to increase

needle travel and increase flow.

C. Air Flow Valve: Adjusts the amount of

atomizing air that is sent to the spray tip to

control the spray pattern. Turn clockwise to

decrease air flow; turn counterclockwise to

increase air flow.

Quick Start Guide for Pressurized Hopper Gun

For spray application of water-based architectural and texture coatings.

Recommended gun settings for different patterns can be found on page 19 of the Operation manual.

WARNING

SETUP

1: When spraying ceilings, the hopper should be tilted forward. When spraying floors, the hopper should be tilted

backward. 2: Apply grease to o-ring on the gun. 3: Loosen hopper clamp, slide it over the rib and toward the top of the

hopper. Position hopper outlet over the hopper port on the gun and push hopper down as far as it will go. Slide down

hopper clamp and hand tighten. 4: Attach tube from hopper barb to gun barb. 5: Apply grease to hopper o-ring. 6: Fill

hopper with prepared texture material. 7: Assemble lid with four clamps. Evenly tighten all four clamps. If there is a leak

from the lid, adjust the clamp tension. The lid should be tightened evenly on the hopper.

NOTICE

Over-tightening the lid may damage

the hopper and/or hopper lid.

OPERATION

1: Connect one end of air hose to the compressor air outlet fitting and the other end to the gun air inlet fitting. 2: Pull up on

material flow regulator knob to unlock. Completely close the air flow valve by turning the knob clockwise; turn the material

flow regulator to the lowest setting counterclockwise. 3: Turn air compressor power switch ON. Adjust air flow valve and

material flow regulator on hopper gun for desired texture. Push down on the material flow regulator to lock settings.

SPRAY PATTERNS (see page 19 of the Operation manual for nozzle & tip recommendations)

Nozzle Pattern WideTex Pattern

Original Instructions. This manual contains English. MM 3A5845. Revision B, May 2018

Table of contents

Other Graco Paint Sprayer manuals

Graco

Graco SDX Operating instructions

Graco

Graco ULTRAX MAX 1595 232164 Instruction Manual

Graco

Graco EH 200 HDI Instruction Manual

Graco

Graco Magnum 261825 User manual

Graco

Graco Reactor E-10 Operation manual

Graco

Graco 24N319 Operation manual

Graco

Graco MAGNUM TRUEAIRLESS DIY Series User manual

Graco

Graco GH 16U277 Operating instructions

Graco

Graco GH 733 HYDRA-SPRAY Operation manual

Graco

Graco 190ES 261825 Operating instructions

Graco

Graco GMAX II 3900 Premium Manual

Graco

Graco 24H685 Troubleshooting guide

Graco

Graco Pro 230ES User manual

Graco

Graco FinishPro 290 Instruction Manual

Graco

Graco Glascraft Formula-X User manual

Graco

Graco SaniSpray HP 750 User manual

Graco

Graco 17C305 Guide

Graco

Graco GH 311797J Operating instructions

Graco

Graco Ultimate MX II FT500 User manual

Graco

Graco GM7000 231327 Operation manual

Graco

Graco LINE LAZER GM 5000 Series Datasheet

Graco

Graco 245095 Assembly instructions

Graco

Graco GX-7A Quick start guide

Graco

Graco Optimiser 2K Operation manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual