Gorenje WA63080 User guide

gorenje

S E R V I C I N G I N S T R U C T I O N S

WASHING MACHINES 4-022-0414

TEHNIČNA PRIPRAVA

SERVISNIH STORITEV

Gorenje, d.d.

3503 Velenje, p.p.107, SLOVENIA

Telephone: +386 63 8990 / 8992 432

Telefax : +386 63 8992 794

PG3 - FAILURES

FAILURE SHORT DESCRIPTION DESCRIPTION FAILURE DISPLAY

connection to temperature

sensor open or short-

circuited

The failure is set, if the connection to the

temperature sensor is open or if there is a

short circuit between the two terminals of

the sensor. The washing program will be

ended without heating. The failure will be

displayed at the end of the washing

program.

On LCD:

ERROR 1

The connection with door

lock is open

The failure is set, if the connection to the

door lock is open. The washing program

will stop. The failure will be displayed.

Supply of door lock will be ON. To start

the washing program, the user has to close

the door (program starts at once). To

continue the program (if failure happens

between washing program), the user has to

check if the door is closed and press the

„Start“-button. If the failure occurs again,

the washing program stops. Supply of door

lock will be OFF. If the water is in the

machine, than pumping 2 minutes. Failure

will be displayed again , and it is not

possible to start the washing program again.

On LCD:

ERROR 2

the water level was not

reached.

- water tap closed

- leak in the machine

- valve defect

The failure is set, if within filling or heating

step the water level is below level 1 for the

filling time or 4 minutes in heating time. If

the failure occurs the first time within a

washing program, the current step starts

again. If the failure occurrs the second time

(twice in succession), the washing program

is stopped, and the failure will be displayed.

To continue the washing program, the user

has to press the „Start“-button. If the failure

occurs the third time, the washing program

stops, the failure will be displayed, and it is

not possible to start the washing program

again.

On LCD:

ERROR 3

the connection to the tacho

generator is open or short-

circuited

If the washing program is active and the

motor control unit gets no signal from the

tacho generator, the first time the failure

occurs a pause of 1minute is executed. This

repeat 3 times. If once happen that motor

works O.K. than all previous failure must

be deleted. When the failure is detected the

4 time’s the washing program stops

immediately. If the temperature is higher

that 60°C than cool down with cold water

30 seconds. Then pumping water 2 minutes.

On LCD: ERROR 4

gorenje

S E R V I C I N G I N S T R U C T I O N S

WASHING MACHINES 4-022-0414

TEHNIČNA PRIPRAVA

SERVISNIH STORITEV VILI GARNBRET

Gorenje, d.d.

3503 Velenje, p.p.107, SLOVENIA

Telephone: +386 63 8990 / 8992 432

Telefax : +386 63 8992 794

STOP the program. The failure will be

displayed.

the triac is short-circuited

The failure is set, if the washing program is

active and the motor is working without

control of triac. The washing program is

stopped immediately. . After 2 minutes try

again. If the failure is not present, than

forget the first failure and continue work. If

is the same failure again, than program

stops complete. If the temperature is higher

that 60°C than cool down with cold water

30 seconds. Then pumping water 2 minutes.

STOP the program. The failure will be

displayed.

On LCD:

ERROR 5

temperature not reached

- heater defect

The failure is set, if after a heating step the

temperature is more than 15°C lower than

the rated temperature. The washing

program will be ended normally. The

failure will be displayed at the end of the

washing program.

On LCD:

ERROR 6

the water level does not fall

below level 1

- pump clogged

- pump defect

The failure is set, if after a pumping step

the water level did not fall below level 1. If

the failure occurs the first time within a

washing program, the current step will

started again. If the failure occurs the

second time (twice in succession), the

washing program is stopped and the failure

is displayed. To continue the washing

program, the user has to press the „Start“-

button. If the failure occurred the third

time, the washing program is stopped and

the failure is displayed. It is not possible to

start the washing program again.

On LCD:

ERROR 7

The WM not reach max.

spin speed (the tapped field

relay does not switch)

The failure is set, if at the end of the

spinning cycle of the testing program the

spin is more than 100rpm lower than the

rated speed. The failure is displayed after

the end of the testing program.

On LCD:

ERROR 8

Water inside machine

(Aqua Stop)

The failure is set, if Aqua Stop Sensor

makes signal (must be measuring min. 2

seconds). All valves switch OFF, the

heater switches OFF and main motor

STOPS. After 3 seconds check again. If the

failure is not present, than forget the first

failure and continue with program. If the

failure is still present, than switch ON the

pump for 2 minutes and stop WM. The

failure is displayed. It is not possible to

start the washing program again.

On LCD:

ERROR 9

gorenje

S E R V I C I N G I N S T R U C T I O N S

WASHING MACHINES 4-022-0414

TEHNIČNA PRIPRAVA

SERVISNIH STORITEV VILI GARNBRET

Gorenje, d.d.

3503 Velenje, p.p.107, SLOVENIA

Telephone: +386 63 8990 / 8992 432

Telefax : +386 63 8992 794

NOTE:

According to the number of fault ton signal is on. This happens 10 times. After that there is no

ton signal but on LCD writes fault till not push button START or switch the machine OFF.

The most important fault is motor, than NTC, than water,…

gorenje

S E R V I C I N G I N S T R U C T I O N S

WASHING MACHINES 4-027-0706

TEHNIČNA PRIPRAVA

SERVISNIH STORITEV

Gorenje, d.d.

3503 Velenje, p.p.107, SLOVENIA

Telephone: +386 63 8990 / 8992 432

Telefax : +386 63 8992 794

Test program for WM with timer PG3

MANUEL ACTION

ACTIVITY INDICATION

Press and hold buttons

START/PAUSE and

EASY IRONING and

turn round the program

knob for 1 step in left

(anti-clock side)

~10”

Self test of micro is executed and test program begins:

- all segments on LCD goes ON for 2 sec.

- after 2’’ on top line write SELF TEST , on bottom line

write max. spin speed for cotton and 99L and all symbols

are ON

- check if is Water clean sensor connect

(read voltage at empty drum)

All step can be 10”.

•If self test O.K, than on top line

write OK (for 2’’) and all other

segments and symbols switch OFF

•If self test is not O.K., than on top

line write ERROR all other

segments and symbols switch OFF,

WM stop

~12"

Door lock control (text on top line DOOR)

- PG3 activated door lock and wait, that contact is close

- max.10 sec)

•If it is O.K. than on top line write

DOOR OK (for 2’’)

•If it is not O.K. than on top line

write DOOR ERROR, WM stop

~4"

NTC control (text on top line NTC))

- check resistance of NTC (can be between 10 to 40°C)

Min. 2 sec

•If it is O.K. than on top line write

NTC OK (for 2’’)

•If it is not O.K. than on top line

write NTC ERROR, WM stop

~62"+20”

Water filling (text on top line WATER)

Open the valves Hot Water, Main Wash and Pre Wash.

Water goes in 3 different space in dispenser.

- HW : 5 ’’ (space 2), if it is connected to hot/cold water

- PW : 10’’ (space 1)

- MW : 10’’ (space 2)

- PW + MW : to reach level 1 (space 1,2 and 3)

- when reached level 1 than it is O.K.

- max. time for all is 60”

•If it is O.K. (before 60” reach level

1) than on top line write WATER

OK (for 2’’)

•If it is not O.K. than on top line

write WATER ERROR, WM stop

~12”

Water clean sensor (text on top line WATER SENSOR)

Only check if it is connected (check voltage at water in

drum together 10”)

•If it is connected than on top line

write WATER SENSOR YES (for

2’’)

•If it is not connected than on top

line write WATER SENSOR NO

~77"

Washing and heating (text on top line WASHING)

- Washing: 15’’ON / 5’’OFF / 15’’ON/5’’OFF

- 3 times repeats washing

- last wash is in spin direction and without pause

- Heater ON all time of washing

All together is 75’’. After this time switch OFF heater,

washing goes to spinning.

•If it is O.K. (after finish wash) –

washing in both direction, than on

top line write WASHING OK (for

2’’ – can be 2” in spinning)

•If it is not O.K. than on top line

write WASHING ERROR (for 2’’),

WM stop

40"

Spinning with water (text on top line SPIN)

- 40’’ spin from 50rpm to max.50 rpm

(or speed define with Pad’s, if is lower that 500 rpm)

- wait to drum stop

~42"

Draining (text on top line DRAIN)

- switch pump ON for 40 “

Check if water level fall under level 1

•If it is O.K. than on top line write

DRAIN OK (for 2’’)

•If it is not O.K. than on top line

gorenje

S E R V I C I N G I N S T R U C T I O N S

WASHING MACHINES 4-022-

0502

TEHNIČNA PRIPRAVA

SERVISNIH STORITEV VILI GARNBRET

Gorenje, d.d.

3503 Velenje, p.p.107, SLOVENIA

Telephone: +386 63 8990 / 8992 432

Telefax : +386 63 8992 794

write DRAIN ERROR, WM stop

~62"

End spinning (text on top line SPIN SPEED)

- pump stay ON

- 10’’ spin from 0 rpm to max. rpm

(if necessary switch ON tape field)

- 50’’ on max. spin speed

- wait to drum stop

- switch OFF all component

•If it is O.K. than on top line write

SPIN SPEED OK (for 2’’)

•If it is not O.K. than on top line

write SPIN SPEED ERROR (for

2’’), WM stop

Turn the program knob

on 0 (OFF) position.

End the test program •On top line exchange (each 1 sec.)

END

WATER SENSOR YES (or NO)

Table of contents

Other Gorenje Washer manuals

Gorenje

Gorenje WA744 Technical manual

Gorenje

Gorenje wa50140 User manual

Gorenje

Gorenje W9825IA Operating and maintenance manual

Gorenje

Gorenje WA1022 User manual

Gorenje

Gorenje w7223 Operating and maintenance manual

Gorenje

Gorenje PWM110WIT Operating and maintenance manual

Gorenje

Gorenje W8844H Operating and maintenance manual

Gorenje

Gorenje WE723 Technical manual

Gorenje

Gorenje W7223UK Operating and maintenance manual

Gorenje

Gorenje washing machine User manual

Gorenje

Gorenje WF2N00260 User manual

Gorenje

Gorenje WA614SYW User manual

Gorenje

Gorenje W8543C Operating and maintenance manual

Gorenje

Gorenje WEI823 Operating and maintenance manual

Gorenje

Gorenje WS53125 User manual

Gorenje

Gorenje WEI74SDS User manual

Gorenje

Gorenje WS53101 User manual

Gorenje

Gorenje WT72122 User manual

Gorenje

Gorenje W8544PB Operating and maintenance manual

Gorenje

Gorenje WT52111 User manual

Gorenje

Gorenje W9865E Operating and maintenance manual

Gorenje

Gorenje W 72ZY2/R User manual

Gorenje

Gorenje W8624H Operating and maintenance manual

Gorenje

Gorenje WP60S3 Technical manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide