goki SmartProducts G1 User manual
Product Type：Goki SmartProducts
Tested Model：G1
To set-up Goki - scan the QR
code or visit support.goki.travel
Goki Pty Ltd
Lvl 2, 11 York St,
Sydney, 2000
Please read the manual carefully before installation and
keep this manual at a secure place
● Please refer to sales agents and professionals for
information not included in this manual. For more support,
please call +61 02 8321 0121
● We reserve the right to upgrade the product without prior
notice.
www.goki.travel
Care & Maintenance
1Please keep the SmartLock away from corrosives.
2Please recharge batteries when you receive a low power
notification on the staff application.
3Please check whether the SmartLock is properly
stabilized every six months, and tighten the screws if
necessary.
Packing List
SmartDiscLocks Handles Mounts Latch
F Screws
Absorbers H Screws Spindle
Parameters
Communication method: Bluetooth 4.1ble
Supporting systems: Android 5.0/IOS7.0
Stand-by current: ≈35μA
Operating current: ≈200 mA
Power supply: Lithium Ion 1150 MAH
Unlock time: ≈1.5 s
Installation
Manual
Two ways are available for deleting Bluetooth Administrator/resetting to default
mode
A.If the lock already has a Bluetooth Administrator, the administrator can delete the
lock on the App when he is near the lock.
B.Long press Reset Button on the lock for 3 seconds till two short beeps are heard.
2.Add Bluetooth Administrator
To add a Bluetooth Administrator to a lock that is in default mode, touch the keypad
to activate the lock. When the backlights are on, add administrator on the App.
3.Unlock with passcode
Input passcode and press“#”. A long beep indicates unlocking successful. Four short
beeps mean unlocking unsuccessful, please check whether the passcode is
correct.
Before a Bluethooth Administrator is added to a lock, the default passcode is
123456
While inputting a passcode, before“#”is pressed, pressing “*” will delete the
previous digit.
Manual
4.Two ways to unlock with App
A.When [Touch to Unlock] feature is on and user’s app is activated, user can unlock
by touching and lightening up the keypad of the lock.
B.Press the Unlock/Lock icon on the App.
A long beep indicates unlocking successful.
5.Lock
A.Long press“#”on the keypad of the lock till two short beeps are heard.
B.Long press the Unlock/Lock icon on the App.
C.When Auto Lock feature is on, the lock locks automatically in pre-set time. Notice:
The default mode of Auto Lock is off.
D. *If the lock comes with a magnetic sensor, it locks automatically when the sensor
detects the door is closed.
The default mode of this feature on.
In case of failure of locking, the lock sounds alarm for 5 times.
Manual
6.Edit user passcode
Input [*10#original passcode#new passcode#new passcode#] on the keypad to
edit passcodes. A long beep indicates editing successful and 4 short beeps mean
editing unsuccessful.
7. Ways to set Auto Lock
A.Input [*21#Admin Passcode#Auto Lock time out(0, 5999 seconds)#] to set Auto
Lock. If“0”is set as the time out, Auto Lock is disabled. Other numbers mean the
time the lock will automatically lock after it is unlocked. The default mode of Auto
Lock is off.
B.For locks equipped with magnetic sensors, the default mode of Auto Lock is on.
Inputing [*23#Admin Passcode#0#] will disable Auto Lock feature. Inputing
[*23#Admin Passcode#1#] will activate Auto Lock feature again.
C.On the App, select the lock, press [Settings][Auto Lock] to edit the settings of
Auto Lock.
8.Low battery alert
If the battery is low, the keypad will light up and flash for a second when it’s
activated.
Manual
9.Keypad lock
The keypad will be disabled for 5 minutes after 5 consecutive trials of wrong
passcode. During the lockout period, the light will flash quickly after each pressing.
Unlocking with App is still functional in this case, and the keypad will be back to
normal once the lock is unlocked successfully with an App.
The keypad will be reactivated after 5 minutes’lockout period, and user can
continue to input passcode. However, each wrong passcode trial will result in 5
minutes’ lockout.
Manual (No APP
10.Edit default Admin Passcode
Before an administrator is added to the lock, default Admin Passcode is 123456
Input [*12#default Admin Passcode#new passcode#new passcode#] to edit Admin
Passcode. A long beep
indicates editing successful and 4 short beeps mean editing unsuccessful.
11.Add Unlocking passcode
Input [*85#Admin Passcode#new passcode#new passcode#] to add a new
unlocking passcode. A long beep indicates adding successful and 4 short beeps
mean adding unsuccessful.
12.Delete all unlocking passcodes
Input [*71#Admin Passcode#] to delete all User Passcodes (including passcodes
generated by App). A long beep indicates deleting successful and 4 short beeps
mean the Admin Passcode is wrong and deleting unsuccessful.
13.Add Bluetooth Administrator
Input [*83#Admin Passcode#] to add Bluetooth Administrator. A Long beep
indicates the lock is ready for App to add a Bluetooth Administrator.
Table of contents
