GIRBAU EH020 Instruction Manual

This manual suits for next models

5

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG

LG TV2516DV3B owner's manual

LG

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Training –Start up procedures

Vended –Logi –Logi Pro controls

Reference manuals:

(1) Operating Instructions Manual for Vended washers Cod. 598144 Rev.

11/0717 or higher X-Series control with Profit Plus

(2) Operating Instructions Manual for Logi control washers Cod. 523340 Rev.

11/1218 or higher section 1-6 Logi Control

(3) Operating Instructions Manual for Logi Pro control washers Cod. 523340

Rev. 11/1218 or higher section 7-8 Logi Pro Control

Rev. 01/0419

2

Safety Instruction

3

Safety Instructions

4

Safety Instructions

5

Safety Instructions

6

Introduction and Use (Vended control & profit plus)

This guide is intended to inform owner/operator of operation and basic equipment set up

for vended controlled washing machines with extra options.

Vended X-series control for EH20, 030, 040, 060, 080 and 090 soft mount units plus

REM025, RMG033, 040, 055 and 070 rigid mount units.

It is important that the customer understand as much as possible during the training

startup of the new equipment. Use the control panel above to explain key functions and

display segments.

Characteristics of the control

•Ease of use microprocessor control

•Ability of individual program modification

•Audit of program usage

•Temperature control achieved by hot and cold valve operation

•Diagnostic “TesT” feature for troubleshooting washer faults

This new control is unique in that it not only allows ease of use but that it has extended

revenue options that can provide up to 30-40% additional income above standard

vended washers. The extra options are: Extra wash time, Extra rinse phase and/or extra

rinse time along with Extra extraction time.

We next want to show customer how to properly setup the washer vending information

for both standard vend and extra options vending best suited for owner’s location. These

settings may vary depending on location. (Consult with owner)

7

Access to Advanced use Mode. All models

With power on, open loading door. Press and hold down key 1 until the COD report

shows on display then release. Next we enter the 4 digit security cod and display will

show “0000”, enter the code a second time and display will show “0000”. Next the

display will show “Pro”. You are now in the advanced menu.

The chart showing all menu’s located in this setup is next. The advanced use mode

offers some menus, which allow the modification of program contents, the price

management of programs and the modification of operation parameters.

Using the washer keypad numbers 2 & 4 you can move back and forth through the menu

choices. Once menu is selected use number 1 to scroll through the menu and use

numbers 2 & 4 to make changes.

For this training the chart provides an explanation of each menu but we will concentrate

on the basic parameters for setting up washer for use. These menus are CASH, EoPt

and Mod. For other menu options refer to the “Operating Instructions Manual for

Vended washers, Cod. 598144 Rev. 11/0717 or later.

Cash (program vend price)

With display showing Pro use key number 2 and move to option indicated CASH. Press

key number 1 to show PR1 indicating program 1, press number 1 to show current price.

To increase price, press number 2 to decrease price or press number 4 until desired

price is showing. Next press number 1 to show PR2 indicating program 2, press number

1 to show current price and use number 2 or 4 to make change. Continue with these

steps until all four programs have been set. Next press Stop 1 time to return to main

menu CASH

EoPt (extra options set up and vend price.

On machines with extra options, the EoPt menu makes it possible to modify the

parameters of these options. With display showing CASH use number 2 key to move to

show EoPt,

8

The extra options are extra wash, extra rinse and extra spin. Each option can be

selected independently from each other, once the washing program has been selected.

In the EoPt menu each of the extra options can be turned off if desired.

In the case of extra wash, the user can choose between turning off and increasing time

of wash phase 2.

In the case of extra rinse, the user can choose between increasing time of wash phase 2

and adding a new phase. Phase 2 and 3 must be active.

This same menu makes it possible to enter pricing for the selected options.

The chart shows each option, option selections and the option default status. Under

EUA we see under options 0 –Off, 1 –Increases the wash time in Phase 2 and 2 –

Adds washing phase. The option 2 adding wash phase is not allowed in USA/Canada

models, only adding of time. The next parameter Ut-x (extra washing time in minutes)

allows for selection of 1 –9 minutes with default at 1 minute.

Note:

Based on what we see in the open markets these times are normally set at a

minimum of 2 minutes with a cost of $0.25 per minute. In the Eri (extra rinse) when

option 2 is selected (adds rinsing phase 5) the cost needs to increase due to the

added water along with time.

9

With display showing EoPt press number 1 and display will show EUA 1, indicating extra

time selection, if you want to turn off this feature press number 2 –4 to change. If extra

time is what you want press number 1 and display will show UT-x 1 indicating 1 minute

of time. To increase time press number 2 until desired time shows. Press number 1 and

display will show 00.00 indicating vend price. Press number 2 and price will increase by

0.25 with each press of key, to lower vend press number 4 key. Once vend is satisfied

press number 1 and display will go to next option Eri 1 indicating extra rinse time.

Continue sequence indicated above until all options are selected and priced. To exit

back to main menu press stop and display will show EoPt. Press number 2 until display

shows Nod.

Mod (Nod) Modification of operational parameters

The Mod menu allows the user to modify the operation parameters of all programs, in

this menu any change made affects all 4 programs as a group. Below we see the

summary table of all changeable parameters, at this time we only want to change the

SP-0setting.

10

As we can see there are several options in this menu screen. The one we want to

address is SP 0 showing in chart as Levels of suds prevention. What it doesn’t tell us

is that it is also the setting for Energy Star programs. These default programs use lower

water levels, lower water temperatures and shorter cycle times.

If we want the washer to work at a standard level of customer satisfaction, we need to

change this setting from SP-0 to SP-1. This will increase the main wash levels,

temperature and times of cycles.

Note:

In order to understand the change of cycles from SP-0 to SP-1 look in section

6.2.2 Program contents. USA configuration, all models. SP-0 and compare to

EH020 and REM025 models. SP-1, SP-2, SP-3. Other EH and RMG models SP-1.

To change setting SP-0 to SP-1, washer display shows Nod, press number 1 until

display shows SP-0, press number 2 and change to SP-1. Press number 1 and you will

hear a long beep then display will show Id-0.

Note: The Id setting is the connection setting for Card systems that allows for the

card provider to communicate directly with washer control through an interface

set up. All washers connected to card systems using this interface requires the Id-

0 setting to be changed to Id-1.

Activation of card system interface;

With display showing Id-0 press number 2 and display will show Id-1 indicating

activation. Press number 1 to confirm change and display will show Nod.

At this time we have completed all standard washer settings and units are now ready for

customer use.

To exit the COD settings press the stop key and display will show door indicating door is

open or Sel indicating door is closed and that washer is in ready mode.

Machine Operation

Main reports that appear on washer display are shown in chart;

Loading the washing machine

Open the loading door and load the machine. Washer load recommendations according

to the type of linen to be washed;

a. Cotton fabrics: nominal load of approximate machine capacity

b. Synthetic fabrics: between 80 & 90% of nominal load