GeoVision GV-R1352 User manual

GV-RK1352 and GV-R1352 Card Reader

The GV-RK1352 and GV-R1352 are card readers designed to recognize identifications cards.

GV-RK1352 comes with keypad, allowing it to also recognize PIN codes. Featured with the

Wiegand and RS-485 outputs, the readers can be connected to any standard access control

panel. The readers are protected by a weather sealed and IP66 compliant housing for

outdoor use.

The content of this installation guide refers to the following readers:

GV-RK1352 firmware V1.2

GV-R1352 firmware V1.2

Packing List

GV-RK1352

1. GV-RK1352 Card Reader

2. Screw x 2

3. Screw Anchor x 2

4. Front Cover Plate x 2

Front View

GV-R1352

December 31, 2014

1. GV-R1352 Card Reader

2. Screw x 3

3. Screw Anchor x 2

4. Security Torx

Front View

1. Physical Descriptions

1.1 Electric Wire

GV-RK1352

Wire Color Function

Red DC 7.5 ~ 12 V

Black GND

Yellow Beeper

Orange Green LED

Light Red Red LED

Green Wiegand Data 0

White Wiegand Data 1

Blue RS-485 +

Light Blue RS-485 -

Rear View

GV-R1352

Wire Color Function

Red DC 7.5 ~ 12V

Black GND

Yellow Beeper

Orange Green LED

Light Red Red LED

Green Wiegand Data 0

White Wiegand Data 1

Blue RS-485 +

Light Blue RS-485 -

Gray N/A

Purple N/A

Brown N/A Rear View

December 31, 2014

1.2 Keypad (GV-RK1352 Only)

When accessing an entry using GV-RK1352, you can enter the door’s PIN code on the

keypad or present the card and then enter the card’s PIN code on the keypad to be granted

access. The access mode is defined on GV-ASManager.

1. 0~9 Number Keys: Press the number keys to enter the PIN code.

2. # Key: Press the # key to confirm the PIN code.

3. ﹡Key: Press the ﹡key to cancel the PIN code.

1.3 LED Indicator and Beeper

In standby mode, the LED is blue. When a card is read, the LED flashes green and the

beeper beeps once.

The reader comes with external control wires for Green LED, Red LED and Beeper. You can

connect these control wires to a GV-AS Controller to change the default settings of the LED

and Beeper. For details on how to configure the settings, refer to 5. Changing the Settings of

Beeper and LED later in this installation guide.

Note: You can only connect the LED and beeper wires to GV-AS210 / 2110 / 400 / 410 /

4110 / 810 / 8110.

December 31, 2014

2. Connecting the Reader to GV-AS Controller

You can connect the readers to GV-AS Controllers through Wiegand or RS-485 interface.

Note that the connection between the reader and GV-AS Controller varies with different

controller models. To see how many readers can be connected to a GV-AS Controller, refer

to The Number of Readers Supported by GV-AS Controllers table at the end of this

installation guide.

Note: GV-RK1352 / R1352 is compatible with GV-AS100 / 1010 / 110 / 120 / 210 / 2110 /

400 / 410 / 4110 / 810 / 8110. However, to enable the keypad function, you can only

connect GV-RK1352 to the controllers through the following interfaces.

GV-AS100 / 110 / 120: through Wiegand interface

GV-AS1010: through RS-485 interface

GV-AS210 / 2110 / 400 / 410 / 4110 / 810 / 8110: through Wiegand or RS-485 interface

2.1 Connecting through Wiegand Interface

The following diagrams use GV-RK1352 and GV-AS810 Controller as an example. Up to

eight readers can be connected to GV-AS810 Controller through the controller’s Wiegand

interface.

Wire Color Function

Black GND

White Wiegand Data 1

Green Wiegand Data 0

Red DC 7.5 ~ 12V

Wiegand A

Note: Connection through Wiegand interface is not supported for GV-AS1010.

December 31, 2014

2.2 Connecting through RS-485 Interface

The following diagrams use GV-RK1352 and GV-AS810 Controller as an example. Up to

eight readers can be connected together to the RS-485 interface on GV-AS810 Controller.

Connecting four or less readers to GV-AS810 Controller:

Wire Color Function

Black GND

Light Blue RS-485 -

Blue RS-485 +

Red DC 7.5 ~ 12V

December 31, 2014

Connecting five or more readers to GV-AS810 Controller:

For readers five to eight, connect the RS-485 cable to the RS-485 interface on GV-

AS810 Controller and then connect the 12V power output and GND of the reader to a

12V DC power output on the controller.

2.2.1 Defining Readers on GV-AS Controller Web Interface

Since multiple readers can connect to GV-AS Controller using one RS-485 interface, you

need to specify which door each reader controls. This section explains how to define readers

on the Web interface of GV-AS Controller. On the Web interface, you can also set the reader

to read the GID or UID on GV-AS ID Cards / Key Fobs. Note that the Web interface of

different GV-AS Controller models varies.

1. On the controller’s Web interface, click Extended Reader. This dialog box appears.

2. In the GV-Reader/CR420/GF1921/GF1922 section, select the RS485 checkbox in front of

the ID number and type the Serial Number on the rear panel of the reader. The ID

number will be assigned to the reader.

December 31, 2014

3. Select a door/gate for the reader from the Function drop-down list.

4. Next to Read Mode, select Read UID or Read GID to set the connected readers to read

UID (unique identifier) or GID (GeoVision ID) on GV-AS ID Cards / Key Fobs.

If you select Read GID, make sure there are two numbers on your GV-AS ID Cards / Key

Fobs as shown below. If there is only one number on your GV-AS ID Cards / Key Fobs,

GID is not supported and you must selec qu ification (UID).t Uni e Ident

5. Click Submit.

Note:

1. When you click Submit on the Extended Reader page of a GV-AS1010 / 210 / 2110 /

410 / 4110 / 810 / 8110, all readers connected through RS-485 interface will reboot.

2. GID ID format is only supported in GV-RK1352 / GV-R1352 V1.2 or later.

December 31, 2014

3. Installing the GV-R/RK/DFR Config AP

master / slave status, and whether it reads UID or GID. When using the Config AP, the

reader needs to be connected to a PC through GV-COM, GV-Hub or GV-NET/IO Card V3.1.

e GV-R/RK/DFR Config AP allows you to set the reader’s beeper / LED, ID number,

You can inst fig AP from the Software DVD or GeoVision Website. To use a GV-

OM, GV-Hub or GV-NET/IO Card V3.1, you also need to install GeoVision USB Device

1. Insert the software CD and the Install Program window will pop up automatically.

2. Select Install GeoVision USB Device Driver.

3. In the GeoVision USB Driver Installer window that appears, select Install.

4. Go back to the Install Program window, and select Run GV-Reader Config Utility.

Downloading from GeoVision Website

1. Go to the Software Download and Upgrading page of GeoVision Website:

http://www.geovision.com.tw/english/5_8_AS.asp

all the Con

river.

Installing from Software CD

2. Find the Supplemental Utilities section under the Access Control tab, and click the

Download icon of GV-RK1352 & GV-R1352 & GV-DFR1352 Config Utility.

3. Under the Driver section, click the Download icon

December 31, 20148

of GV-USB Device Driver.

4. Overlaying Card Numbers on GV-System Live

View

You can overlay card numbers recognized at the reader onto a camera channel on GV-

System. To overlay card numbers on GV-System channel, the reader needs to be connected

to a GV-System through GV-COM, GV-Hub or GV-NET/IO Card V3.1.

RS-485

GV-HUB / GV-COM /

GV-NET/IO Card

RS-232

GV-System

(Light Blue) RS-485 -

(Blue) RS-485 +

USB

GV-RK1352

or GV-R1352

Note: GV-RK1352 / GV-R1352 is not compatible with GV-NET Card and GV-NET/IO Card

of versions earlier than V3.

4.1 Defining the ID Number and Setting the Reader to Slave

After the reader is connected to the computer of the GV-System, use the GV-R/RK/DFR

. Run GV-R/RK/DFR Config AP. Refer to 3. Installing the GV-R/RK/DFR Config AP above

Config AP to define the ID number of the reader and set the reader to Slave.

for how to install.

December 31, 2014

2. Select the COM port that is connected to the reader and click Open COM. The seria

number and firmware version of the reader will be automatically detected. The red s

next to

3. Under

quare

the COM port box should change to blue to indicate the COM port is correct.

Master / Slave, set the reader to Slave.

If you want to connect multiple readers to the GV-System, you need to set up a unique ID

number for each reader. For this you need to connect each reader to the computer one

reader at a time, and follow the instructions above to set up an ID number.

4. Select an ID number for the reader. The ID number ranges from 0 to 7.

5. Click Setup. The settings are sent to the reader.

Note:

1. If the COM port is incorrect, an “Error opening serial port”message will appear. To

verify the COM port that is connected to the reader, go to Windows Device Manager. In

the Ports (COM & LPT) field, you should see the entry for Prolific USB-to-Serial

Comm Port and the COM number currently in use.

2. If you are using an older version of the Config AP, you will have to manually type the

serial number of the reader. The serial number is on the rear panel of the reader.

December 31, 2014

Other manuals for GV-R1352

This manual suits for next models

Table of contents

GeoVision GV-R1352 User manual

Popular Card Reader manuals by other brands