Genie WNVRN14P5 User manual

Quick Start Guide

Please read these instructions carefully before operating the unit

and keep for further reference.

PoE 4 Channel H.265 8MP NVR

with 1HDD Bay

WNVRN14P5

Intro Section

Please read this instruction carefully before operating the product and keep it for further

reference. All examples and pictures used here are for reference only.

The contents of this manual are subject to change without notice.

This device should be operated only from the type of power source indicated on the

marking label. The voltage of the power must be veriﬁed before use.

CAUTION:

• Please check the device and the accessories after getting the device. If there are any

damages, shortages or defects, please contact your dealer immediately.

Contents

iii

1.0 Introduction..........................................................................................................4

1.1 Product Features...........................................................................................4

1.2 Product Dimensions.....................................................................................4

1.3 Speciﬁcation.................................................................................................5

2.0 HDD Installation...................................................................................................6

3.0 Rear Panel Instruction..........................................................................................7

4.0 Start Up and Shut Down......................................................................................8

5.0 Login ....................................................................................................................9

6.0 Conﬁgurations and Connections ........................................................................10

6.1 Network Conﬁguration & Adding IP Camera...............................................10

7.0 UPnP .....................................................................................................................12

8.0 NAT.......................................................................................................................13

9.0 Manual Recording and Playback .........................................................................14

9.1 Manual Recording.........................................................................................14

9.2 Playback.......................................................................................................14

The Genie WNVRN14P5 is a 4 channel high deﬁnition 8MP network video recorder that

features 4 channel simultaneous playback as well as 4 PoE network ports with IPC direct

connection to the NVR. The NVR can support the latest H.265 bandwidth and has a

dedicated iPhone and Android App (Super Live Plus) as well as being supplied with free

Windows / MAC CMS software.

1.1 Product Features

• Support 4CH 8MP / 6MP / 5MP / 4MP / 3MP / 1080p / 1280×1024 / 960p / 720p /

960H / DI / CIF IP video input

• Adopt standard H.265 and H.264 high proﬁle compression format to get high-quality

video at much lower bit rate

• Intuitive and user-friendly Graphic User Interface ( GUI ), Windows style operation by

mouse

• Multi-mode recording: manual / timed / motion / sensor / POS / AI recording

• Search : time slice, time, event, tag, smart search

• Playback : 4CH simultaneous playback

• Support multiple VCA (Video Content Analytics) events, such as object abandoned /

missing, region intrusion, tripwire, video exception, etc.

• Support POS information overlay on live view and playback

• Express and ﬂexible backup via USB, network and so on

• Pentaplex : preview, record, playback, backup and remote access

• Remote control via Web or CMS : preview, playback, backup, PTZ and conﬁguration

• DHCP, DDNS, PPPoE network protocol

• Multi-user online simultaneously

• 4 PoE network ports, IPC can be directly connected to NVR, PoE power supply

supported

• Dual stream technology for local storage with high deﬁnition, remote network

transmission and remote surveillance with mobile device

• Authorisation management, log view and device status view

• 4K output, true high resolution display

• Support NAT function and QR Code scanning by mobile phones

• Powerful mobile surveillance by smart phones with iOS and Android OS

• NDAA compliant

1.2 Product Dimensions

1.0 Introduction

300mm

249mm

45mm

Quick Start Guide PoE 4 Channel H.265 8MP NVR with 1HDD Bay

1.3 Speciﬁcation

Model WNVRN14P5

System OS Embedded Linux

Video

Network Input 4 CH IPC input

Network Input Resolution 8MP/6MP/5MP/4MP/3MP/1080p/1280×1024/960p/720p/960H/D1/CIF

Output HDMI x 1: 3840×2160 / 1920×1080 / 1280×1024 / 1024×768

VGA: 1920×1080 / 1280×1024 / 1024×768

Compression H.265S /H.265+ / H.265 / H.264

Audio

Network Input 4 channel IPC audio input

Two Way Audio RCA x 1

Audio Local Output RCA x 1

Compression H.265S /H.265+ / H.265 / H.264

Record Resolution 8MP/6MP/5MP/4MP/3MP/1080p/1280×1024/960p/720p/960H/D1/CIF

Frame Rate NTSC:30fps, PAL:25fps

Mobile Device OS iOS, Android

Storage HDD SATA3.0 × 1, max 10TB

Playback

Simultaneous Playback 4 channel max.

Search Time slice / Time / Event / Tag search / Smart Search

Smart Search Highlight colours to display the camera record in a certain period of time, different

colours refer to different record events

Function Play, Pause, FF, FB, Digital zoom, etc

Decoding Capability 1CH 8MP, 4CH 1080p Live View / Playback

Network

Interface RJ 45 × 1 (10/100/1000Mbps)

Protocol TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP, HTTP, HTTPs, 802.1x, ONVIF, etc.

Incoming / Outgoing

Bandwidth 40/40 (Mbps)

Client Connection Max. 10 users access

Alarm

Mode Manual, Sensor, Motion, Exception

Input Support IPC alarm input

Output Support IPC alarm output

Triggering Record, Snap, Preset, E-mail, etc.

Remote

Monitoring

Immix Compatible with Immix via RTSP only (2-way audio not supported)

Sentinel Yes, Firmware 1.1.0 or later

Backup Local Backup USB stick, USB mobile HDD

Network Backup Yes

Port

USB USB 2.0 × 2

Remote Controller Optional

PoE Ports 100M RJ45 × 4

Others

PoE Standards: IEEE802.3AF/AT

Output Power: ≤ 48W

Power Supply DC 48V/1.25A

Consumption ≤ 10W ( without HDD )

Dimensions 300 × 249 × 45 mm

Working Environment -10°C~50°C, 10%~90% humidity

Certiﬁcate CE, FCC

Environmental Protection Complies with Directive EU RoHS, REACH and WEEE

This series of the product supports 1 SATA hard drives. Please make sure that the device is

powered off before the installation. The pictures of the installation are for reference only.

1. Loosen the screws to open the cover.

2.0 HDD Installation

2. Place the HDD onto the bottom

of the machine.

3. Put the HDDs onto the bottom of the

device.

4. Connect the power and data

cables.

5. Turn over the machine and secure

the HDD with the screws.

6. Install back the cover and secure

it with the screws.

Note: Please check the inside structure of the device and make sure that the cables are

connected well before installing the cover back. Please format the HDD before using.

The interfaces of the rear panel are for reference only.

3.0 Rear Panel Instruction

AUDIO

OUT

DC48V

USB LAN

VGA

AUDIO

IN 2

PoE PO RTS

Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

Shutdown

Click “Start” and then select “Shutdown” icon. This will bring up a shutdown window. The

device will shut down by clicking “OK” button. Then disconnect the power.

4.0 Start Up and Shut Down

The default username is admin and the default password is 123456. You must conﬁgure the

wizard if you start the NVR for the ﬁrst time and you may change the password when you

conﬁgure the wizard for the ﬁrst time. You can skip the settings wizard next time.

Click “Start” and select “Login”. This will take you to see a login box. Enter the default

username and password you set. Then you will see the live image.

5.0 Login

6.0 Conﬁgurations and Connections

6.1 Network Conﬁguration & Adding IP Camera

After you ﬁnish adding IP cameras, you can see the live images through the monitor of the

NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.

LAN

1. Set the network of the NVR. Go to Start → Settings → Network → TCP/IP. Enter IP

address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the

NVR and the router.

2. Go to Start → Settings → Network → Port. Enter HTTP port (the default value is 80),

server port (the default port is 6036).

3. The internal ethernet port is the port which connects all the PoE ports with the NVR

system. The PoE ports are available if the internal ethernet port is online. If it is ofﬂine,

all the PoE ports will be unavailable. The IP address and subnet mask of the internal

ethernet port can be changed to make the port in the same network segment with the

IP cameras which directly connect to the PoE ports of the NVR.

4. Go to Start → Settings → Camera → Add Camera. The NVR will automatically refresh the

cameras searched. The IPC which supports the Onvif protocol may be added manually.

If the IPC searched is not in the same local network as the NVR, you should select the

device and click to modify the IP address.

Table of contents

Popular DVR manuals by other brands

FLIR

FLIR M3100E Series instruction manual

VTRACKPRO

VTRACKPRO FPRO300 user manual

Swann

Swann NVR-7085 models instruction manual

XtendLan

XtendLan DVR-1670C user manual

urmet domus

urmet domus 1093/004AHD instructions

Holux

Holux M1 user manual

CMOS DOTCOM

CMOS DOTCOM ANX-1670 manual

Whistler

Whistler D16VRS user guide

Defender Security

Defender Security 82-20235 user manual

MISUMI

MISUMI MP-WF100M user guide

Speco

Speco D8HU user guide

UST

UST DDR-E04AA Hardware user manual

Consolidated

Consolidated Digital Video Recorder user manual

Mace

Mace DVR0404RW Operational manual

RCA

RCA RTD315W user manual

FSM

FSM Colibri Grande PRO user manual

Hauppauge

Hauppauge HD PVR 2 Quick install guide

Identivision

Identivision ICR-PH161i PIONEER user manual