Geermarc AMPLICALL16 User manual
0
AMPLICALL16
Doorbell Amplifie
r
Sonnette Amplifiée
Türklingel Verstärke
r
English page1
Français page9
Deutsch page17
1
Description
DESCRIPTION
Adaptor jack
(OPTIONAL)
Battery
compartment
(4 X AA )
REAR
Pairing/Testing
button
FRONT
Volume control
Speaker
Low battery indicator
Table Mount
Strobe flasher
2
Installation (See drawing)
1 – Insert the 23A 12V battery into the door bell.
2 – Insert the 4 (AA) batteries into the battery
compartment main unit or connect the adaptor 7.5V
DC/1A (optional).
Electrical connection : The apparatus is designed to
operate from a 230V 50Hz supply only. (Classified as
«hazardous voltage» according to EN60950 standard).
The apparatus does not incorporate an integral power
on/off switch. To disconnect the power, either switch off
supply at the mains power socket or unplug the AC
adaptor. When installing the apparatus, ensure that the
mains power socket is readily accessible.
INSTALLATION
A
C ada
p
tor
(
o
p
tional
)
230V
Door Bell
Door Bell button
3
Setting up the Door Bell
1. The door bell can be carried around by people who
need assistance
2. The door bell can be fixed on the wall or a door frame.
Drill two holes horizontally, 14mm apart. Insert the two
supplied anchors into the two holes. Hang the door bell
onto the two anchors and then insert and tighten the
screws. Finally, stick the blank sticker over the two
holes.
3. The door bell can be stuck onto a door or window
using the supplied strong adhesive tape. Remove the
protective paper from the adhesive tape on the back of
the door bell and then stick to the required door,
window or surface.
Wall Mounting the Chime Unit
1. Drill two holes horizontally, 96mm apart, and leave the
screws protruding from the wall by 5mm.
2. Hang the base on to the two screws and pull the base
down to lock it.
Table Mounting
If you want to mount the unit on the table simply place the
unit into the base cradle, and then place the base cradle
on the table.
INSTALLATION
4
Change the Battery of the Indoor Unit (optional)
The unit requires 4×AA batteries
1. Open the battery door.
2. Insert four AA batteries into the compartment.
3. Snap the battery compartment door back into place.
Note: When the low battery indicator keeps flashing, it is
time to replace the batteries. Alternatively, use a mains
adaptor as an option (contact 01707 387602).
Install and Change the Battery of the Door bell
Install the 23A 12V battery into the door bell
To replace the battery, unscrew the door bell from the
wall, and unscrew the one screw located on the back to
gain access to the battery compartment. Replace the
battery then replace the battery compartment flap and
screw and remount.
Note: Do not use a rechargeable battery. Do not put the
used battery into the household rubbish, pay attention to
regulations regarding battery disposal.
INSTALLATION
5
Volume Control Slide Switch
The volume control slide switch can be used to set the
volume of the alarm sound and switch the unit on/off.
The Pairing Procedure:
The supplied door bell has been paired with the base,
there is no need to pair them. If the door bell is not paired
with the base or you wish to pair the base with another
door bell, please follow the pairing procedure below:
Press and hold the Pairing/Test button of the unit whilst
pressing the doorbell button until the strobe flasher LED
starts to flash. The unit will make a beep sound to confirm
that pairing has taken place successfully.
Please note that the pairing procedure overwrites the last
doorbell that was paired to the unit.
To check whether the device is working properly and has
been paired correctly, press the pairing/testing button
once. The device should sound the alarm and flash.
Operation
Once the Amplicall 16 and the door bell have been
placed in the required locations and all required batteries
have been inserted, you are ready to use the device.
To use the device, the person who needs assistance
must press the door bell button of the door bell.
INSTALLATION
6
Trouble shooting
Symptom Solution
The unit makes the
“dingdong” sound (ad
hoc or continuously)
without the door bell
being pressed
1) Check the batteries are
inserted correctly
2) Check the power adaptor
is inserted into the unit
and the wall correctly (if
using mains power)
3) Turn off the power switch
for 10 minutes and then
turn it on
Low battery LED is
flashing.
1) Turn off the power switch
for 10 minutes and then
turn it on
2) Insert new batteries into
the base unit
Batteries and power
adaptor are connected
correctly, yet no
“Dingdong” sound when
the door bell is pressed.
1) Turn off the power switch
for 10 minutes and then
turn it on
2) Replace the base unit
batteries
3) Replace the door bell
batteries
TROUBLESHOOTING
7
From the moment your Geemarc product is purchased,
Geemarc guarantee it for the period of two years.
During this time, all repairs or replacements (at our option)
are free of charge. Should you experience a problem
then contact our helpline or visit our website at
www.geemarc.com. The guarantee does not cover
accidents, negligence or breakages to any parts. The
product must not be tampered with or taken apart by
anyone who is not an authorised Geemarc
representative.The Geemarc guarantee in no way limits
your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR
GUARANTEE AND MUST BE RETAINED AND
PRODUCED IN THE EVENT OF A WARRANTY CLAIM.
Please note : The guarantee applies to the United
Kingdom only.
Declaration : Hereby Geemarc Telecom SA declares
that this product is in compliance with the essential
requirements and other relevant provisions of the Radio
and Telecommunications Terminal Equipment Directive
2014/53/UE and in particular article 3 section 1a, 1b and
section 2.
The declaration of conformity may be consulted at
www.geemarc.com
GUARANTEE
8
Recycling directives : The WEEE (Waste Electrical and
Electronic Equipment) has been put in place for the
products at the end of their useful life are recycled in the
best way.When this product is finished with, please do
not put it in your domestic waste bin.Please use one of
the following disposal options:
- Remove the batteries and deposit them in an
appropriate WEEE skip. Deposit the product in an
appropriate WEEE skip.
- Or, hand the old product to the retailer. If you purchase
a new one, they should accept it. Thus if you respect
these instructions you ensure human health and
environmental protection.
For product support and help visit our website
at www.geemarc.com
Telephone 01707 387602
Or fax 01707 832529
GUARANTEE
9
Descriptif
DESCRIPTIF
Prise adaptateur
(option)
Compartiment
des batteries
(4 X AA)
ARRIERE
Bouton d’enregistrement
sonnette
/
Bouton de tes
t
Flash lumineux
Réglage du volume
Sonnerie
Indicateur de
batterie faible
Socle AVANT
Table of contents
Languages:
Other Geermarc Accessories manuals
