Garmin AMPS Rugged Mount User manual

Instructions

AMPSRuggedMount

MONTANA™600Series

AMPSRuggedMountInstructions





See the Important Safety and Product Information in the Montana product box

before installing the rugged mount.

notice

Incorrectly wiring the power/audio cable with bare wire leads can result in damage

to the vehicle or the battery. Garmin strongly recommends having an experienced

installer with the proper knowledge of electrical systems install the mount.



• AMPS Rugged Mount

• Anti-glare screen protector with applicator card and instructions

• 4 nuts and 4 washers (for AMPS mount)

• 4 screws (for AMPS mount)

• Security screw tool

NOTE: Installation of the rugged mount to all vehicles requires an AMPS mount

(not included).



Garmin’s standard limited warranty applies to this accessory. For more

information, see the Important Safety and Product Information in the Montana

product box.

AMPSRuggedMountInstructions



notice

If any wire is left unconnected, insulate the wire and safely secure it on your

vehicle.

1. Select a location to mount the Montana on your vehicle, based on available

power sources, safe cable routing, and that the driver view is not obstructed.

2. Connect the red

➊

and black

➋

wires to your vehicle’s main power (10 to 50

Volts).

➏

➋

➊

➌

➍

➎

3. If necessary, connect the serial data wires to your vehicle.

• Yellow

➌

is the serial data input wire.

• Blue

➍

is the serial data output wire.

• Green

➎

is the serial ground wire.

4. If necessary, connect the audio jack

➏

AMPSRuggedMountInstructions



The AMPS mount is not included with the rugged mount.

1. Thread the screws

➊

through the washers

➋

, mount

➌

, and AMPS mount base

plate

➍

(not included).

➊

➋➌

➍

➎

2. Tighten the nuts

➎

to secure the base plate.

The recommended torque is 15–20 lbf-in (1.7 to 2.25 Nm).



notice

Before placing the device in the mount, ensure that the metal contacts on the

device and the mount are dry to avoid equipment damage. Use the weather cap to

keep the mount cradle dry.

1. Place the weather cap

➊

in the storage area on the mount.

➋

➊

➌

2. Fit the bottom of your device into the cradle

➋

3. Tilt the device back until it snaps into place.

4. Using the security screw tool, tighten the security screw

➌

on the top of the

mount.

NOTE: If reected light or glare makes the device display difcult to see, apply

an anti-glare screen protector to the screen.



1. Loosen the security screw.

2. Press the button on the side of the mount to release

the device.

3. Lift out the device.

4. Place the weather cap

➊

on the cradle.

➊

Shop for other gadgets & electronics on our website.

Table of contents

Other Garmin Accessories manuals

Garmin

Garmin IMPACT User manual

Garmin

Garmin Marine Network Cable Connector (RJ45, 2-pack User manual

Garmin

Garmin SPEED SENSOR 2 User manual

Garmin

Garmin GLO Glonass User manual

Garmin

Garmin GHC 10 User manual

Garmin

Garmin GDL 90 User manual

Garmin

Garmin GFS 10 - Fuel Sensor User manual

Garmin

Garmin Speed Sensor User manual

Garmin

Garmin GDL 90 UAT Quick start guide

Garmin

Garmin GTM 10 - TMC Module Reference guide

Garmin

Garmin GPSMAP 5012 - Marine GPS Receiver Configuration guide

Garmin

Garmin SPEED SENSOR 2 Instruction manual

Garmin

Garmin LIDAR-LITE V4 LED Instruction manual

Garmin

Garmin GSC 10 - Speed User manual

Garmin

Garmin SPEED SENSOR 2 User manual

Garmin

Garmin nuvi 350 User manual

Garmin

Garmin interstuhl S4.0 Instruction manual

Garmin

Garmin GPSMAP 520 - Marine GPS Receiver User manual

Garmin

Garmin GSC 10 User manual

Garmin

Garmin GWS 10 Marine Wind Sensor User manual

Garmin

Garmin GWS 10 Marine Wind Sensor User manual

Garmin

Garmin nuvi 500-Series Operating manual

Garmin

Garmin A03451 Instruction manual

Garmin

Garmin GFS 10 - Fuel Sensor Reference guide

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual