Fysic FX-3940 User manual
USER’S MANUAL
FX-3940
2
CONTENTS
1. NETWORK COMPATIBILITY ......................... 4
2. MAINTENANCE.............................................. 5
3. INSTALLATION
3.1 Table stand ...................................................... 5
3.2 Wall-mounting.................................................. 6
3.3 Batteries .......................................................... 7
3.4 Power adapter ................................................. 8
3.5 Receiver .......................................................... 8
3.6 Telephone........................................................ 9
3.7 Connection ‘vibrat’........................................... 9
4. SETUP .......................................................... 10
5. USING THE TELEPHONE
5.1 Incoming calls................................................ 12
5.2 Answering calls ............................................. 12
5.3 Call timer ....................................................... 13
5.4 Ending calls ................................................... 13
5.5 Dialling numbers............................................ 13
5.6 Pre-dialling .................................................... 14
5.7 Re-dialling last number(s) ............................. 14
5.8 Dialling direct memories ................................ 15
5.9 Dialling phonebook memories ....................... 15
5.10 Dialling phonebook memories ....................... 16
5.11 R button......................................................... 17
5.12 * and # buttons .............................................. 18
3
6. Caller-ID
6.1 Introduction.................................................... 19
6.2 New call indication......................................... 19
6.3 Checking the memory & calling back ............ 20
6.4 Copying calls to the phonebook .................... 20
6.5 Deleting calls ................................................. 21
6.6 Remarks & tips regarding Caller-ID .............. 22
7. NUMBER MEMORY
7.1 Introduction.................................................... 24
7.2 Programming................................................. 25
7.3 Dialling from the memory .............................. 28
7.4 Changing / correcting .................................... 28
7.5 Deleting ......................................................... 29
7.6 Service access .............................................. 29
8. WARNINGS AND USER TIPS
8.1 General.......................................................... 33
8.2 Installation ..................................................... 33
8.3 Environment .................................................. 34
9. PROOF OF WARRANTY.............................. 35
4
1. NETWORK COMPATIBILITY
This telephone is designed for use on the ‘public
switched telephone networks (analogue single
line)’ of telephony and cable companies in all
countries of the EU.
However, each provider could require a dierent
connecting wire with plug.
This device meets the essential requirements
and other relevant provisions as stipulated by the
European Guideline 1999/5/EC.
Loading factor: 50
5
2. MAINTENANCE
• Only clean the housing with a moist cloth,
never use chemical cleaning agents.
• Never place the FX-3940 onto cellulose-treated
surfaces; the rubber feet could leave tracks.
3. INSTALLATION
3.1 Table stand:
When using the telephone on a table or desk, you
should rst attach the table stand to the bottom of
the telephone.
1. rst, hook this
side of the stand
into the bottom
of the telephone
(see 1)
2. now push the other side of the stand into the
bottom until the 2
clips lock (see 2),
if necessary de-
press these clips
somewhat (see 3)
1
2
3
6
When you want to
detach the stand
again, press at 3
and remove in the
direction of 4.
3.2 Wall-mounting:
1. in a vertical line, drill
2 holes at a distance
of 8.4 cm from each
other and insert plugs
and screws; let the
head of the screws
protrude for 5 mm
2. slide the receiver
clamp out of the
telephone, turn it
180° and place it
back onto the tele-
phone; this clamp
will hold the receiver
in case of wall-
mounting
8,4cm
3
4
7
3. hook the telephone with the screw holes over
the screws and press it downward
4. x the telephone wire to the wall using the cable
clips
In case of wall-mounting, the table stand is NOT
used.
3.3 Batteries:
The display of the telephone is powered by the
supplied power adapter. You can install 4 backup
batteries to ensure the display will also keep work-
ing during a power outage.
Attention: do NOT remove the battery
compartment cover while the telephone is
connected with the telephone line.
1. use a sharp object to remove the battery cover
and open the compartment.
2. insert 4 AAA (pencil cells) according to the
markings inside the battery compartment.
3. replace the battery cover and make sure it
“clicks” onto the telephone.
8
3.4 Power adapter:
The power adapter must be connected to be able
to use the additional functions, such as hands-free
calling and the speaker function
1. connect the supplied power adapter to the
DC12V input at the bottom of the telephone.
2. insert the power adapter into a 230V AC wall
socket.
Only connect the supplied power adapter.
Connection other power adaptrs with dif-
ferent specications can damage the tele-
phone or even cause a re.
3.5 Receiver:
1. connect the receiver with
the telephone by attach-
ing one side of the spiral
cable to the bottom of the
receiver and
the other side
to the left side
of the tele-
phone
2. push in the plugs until they’re securely connected
9
3.6 Telephone:
1. plug the telephone wire into
the bottom of the telephone
2. insert the telephone plug into
a telephone wall socket
3.7 Connection ‘Vibrat’
The bottom of the phone is provided with a ‘Vibrat’
connection for connecting a shaker that vibrates
when receiving incoming calls. This shaker is not
included, but can be purchased from the Fysic
customer service. See the back of this manual for
address information.
10
4. SETUP
Follow the steps below to set the display lan-
guage, display contrast and time/date.
press the STOR button
Language:
the display will show a language, use
and to select the desired lan-
guage
press OK
LCD contrast:
the display will show the current con-
trast setting, use and to select
the desired contrast and press OK
time/date:
use and to adjust the settings in
the following order:
the hours, press OK,
the minutes, press OK,
the date, press OK,
the month, press OK
Table of contents
Other Fysic Telephone manuals
