Furuno RD-30 User manual

Installation Manual

MULTI DISPLAY RD-30

SAFETY INSTRUCTIONS....................................................................i

SYSTEM CONFIGURATION...............................................................ii

EQUIPMENT LISTS...........................................................................iii

1. INSTALLATION...............................................................................1

1.1 Installation of Display Unit........................................................................................1

1.2 Wiring.......................................................................................................................3

2. INITIAL SETTINGS.........................................................................7

2.1 Data Sentence Description ......................................................................................7

2.2 IEC 61162-1 (NMEA 0183) Input Data Sentences ...................................................8

2.3 Setting Input/Output.................................................................................................9

PACKING LIST................................................................................A-1

OUTLINE DRAWINGS....................................................................D-1

INTERCONNECTION DIAGRAM.................................................... S-1

www.reelschematic.com

Your Local Agent/DealerYour Local Agent/Dealer

9-52 Ashihara-cho,9-52 Ashihara-cho,

Nishinomi

a, Ja

anNishinomi

a, Ja

Tele

hone :Tele

hone : 0798-65-21110798-65-2111

Telefax :Telefax : 0798-65-42000798-65-4200

IRST EDITION :

IRST EDITION : MAR.MAR. 20012001

Printed in JapanPrinted in Japan

ll ri

hts reserved.

ll ri

hts reserved. E1E1 :: FEB.FEB. 03,200303,2003

PUB.No.PUB.No. IME-44130-E1IME-44130-E1

*00080917801**00080917801*

(( YOSHYOSH )) RD-30RD-30 * 0 0 0 8 0 9 1 7 8 0 1 ** 0 0 0 8 0 9 1 7 8 0 1 *

*IME44130E10**IME44130E10*

* I M E 4 4 1 3 0 E 1 ** I M E 4 4 1 3 0 E 1 *

www.reelschematic.com

SAFETY INSTRUCTIONS

WARNING

Turn off the power at the

switchboard before beginning the

installation.

Fire or electrical shock can result if the

power is left on.

Be sure that the power supply is

compatible with the voltage rating of

the equipment.

Connection of an incorrect power

supply can cause fire or equipment

damage. The voltage rating of the

equipment appears on the label above

the power connector.

Do not open the cover unless totally

familiar with electrical circuits and

service manual.

Improper handling can result in

electrical shock.

CAUTION

Observe the following compass

safe distances to prevent

interference to a magnetic

compass:

Ground the equipment to

prevent mutual

interference.

Display

unit

Standard Steering

0.35 m 0.25 m

www.reelschematic.com

SYSTEM CONFIGURATION

Multi display

RD-30

Multi display

RD-30

Multi display

RD-30

GPS receiver

GP-310B

GPS receiver

GP-310B

Sensor

Navigator

Ship's mains

12-24 VDC

: Standard

: Option

PWR

ENT

DISP DIM

FURUNO

RD-30

PWR

ENT

DISP DIM

FURUNO

RD-30

PWR

ENT

DISP DIM

FURUNO

RD-30

Sensor

www.reelschematic.com

iii

EQUIPMENT LIST

Standard supply

No. Name Type Code No. Qty Remarks

1 Multi Display RD-30 - 1

2 Spare Parts SP14-02901 - 1 set

3 Installation

Materials CP14-06000 - 1 set +Tapping screw (4 pcs)

MJ-A7SPF0005-020

4 Accessories FP14-02801 - 1 set Hard cover

Optional supply

No. Name Type Code No. Qty Remarks

1 Flush Mount Kit S OP20-17 000-040-720

2 Flush Mount Kit F OP20-29 000-041-405 1 For flush

mounting the

display unit

MJ-A7SPF0005-020 000-139-384 1 Power, signal

MJ-A7SPF0006-100 000-143-578 1 7P-7P

cross cable

3 CableAssy.

MJ-A7SPF/SRMD-100 000-144-534 1 7P-7P

straight cable

Sensors available

No. Name Type Code No. Qty Remarks

1 Smart Sensor 235DT-MSE 000-144-981 1 Depth & Temperature

Sensor

2 Smart Sensor 235DT-PSE 000-144-982 1 Depth & Temperature

Sensor

3 Smart Sensor 235DST-PWE 000-144-983 1 Depth, Speed and

Temperature Sensor

4 Smart Sensor 235DHT-LMSE 000-144-984 1 Depth and High Precision

Temperature Sensor

5 Smart Sensor 235DHT-MSE 000-144-985 1 Depth and High Precision

Temperature Sensor

For technical specifications seeAirmar’s technical data.

www.reelschematic.com

This page is intentionally left blank.

www.reelschematic.com

1. INSTALLATION

1.1 Installation of Display Unit

Mounting considerations

The display unit can be installed on a tabletop, on the overhead, or in a

panel (optional flush mounting kit required). Refer to the outline drawings

at the end of this manual for installation instructions. When selecting a

mounting location, keep in mind the following points:

• Locate the unit away from exhaust pipes and vents.

• The mounting location should be well ventilated.

• Mount the unit where shock and vibration are minimal.

• Locate the unit away from equipment which generates electromagnetic

fields such as a motor or generator.

• Allow sufficient maintenance space at the sides and rear of the unit and

leave sufficient slack in cables, to facilitate maintenance and servicing.

• Observe the following compass safe distances to prevent deviation of a

magnetic compass.

Standard compass, 0.35 m, Steering compass, 0.25 m.

Tabletop and overhead mounting

Tabletop Overhead

Figure 1-1 Tabletop and overhead mounting methods

www.reelschematic.com

Flush mounting

There are two types of flush mount kits, F type and S type. For details, see

the outline drawings at the back of this manual.

F type

Flush mount kit F (Type: OP20-29, Code No.: 000-041-405)

No. Name Type Code No. Qty Remarks

1 Cosmetic Panel 20-016-1051 100-251-370 1

2 + Tapping Screw 5x20 SUS304 000-802-840 4

3 Hex Bolt M6x12 SUS304 000-862-127 2

4 Spring Washer M6 SUS304 000-864-260 2

1. Make a cutout of 183 X 92 mm.

2. Attach the cosmetic panel (supplied) to the display unit with hex bolts

(M6X12, supplied) and spring washers (M6, supplied).

3. Fix the display unit to the mounting location with four tapping screws

(5X20, supplied).

S type

Flush mount kit S (Type: OP20-17, Code No.: 000-040-720)

No. Name Type Code No. Qty Remarks

1 Fixing Metal 20-007-2401 100-183-190 2

2 Wing Bolt M4x30 YBSC2

MBN12 000-804-799 4

3 Hex Bolt M6x12 SUS304 000-862-127 2

4 Wing Nut M4 YBSC2

MBN12 000-863-306 4

5 Spring Washer M6 SUS304 000-864-260 2

1. Make a cutout of 167 X 92 mm.

2. Attach two fixing metals (supplied) to the display unit with hex bolts

(M6X12, supplied) and spring washers (M6, supplied).

3. Screw four wing bolts (supplied) into wing nuts (supplied).

4. Fasten the display unit to the mounting location with four sets of wing

bolts and nuts assembled at step 3.

www.reelschematic.com

1.2 Wiring

The figure below shows where to connect cables on the rear of the display

unit.

Black Red

POWER

(12-24 VDC) Ground

1A FUSE

(+ Line)

DISPLAY

UNIT

DISPLAY

UNIT

GPS

RECEIVER

Ground the equipment to

prevent mutual interference.

CAUTION

Figure 1-2 Wiring

Note: The fuse holder contains a spring which fixes the fuse. To prevent

detachment of the spring, which would cause loss of power, tie the

line as shown in Figure 1-3.

Fuse holder

+ line (red)

Tie here.

Figure 1-3 How to fix spring in fuse holder

www.reelschematic.com

Grounding

The display unit contains a CPU. While it is operating, it radiates noise,

which can interfere with radio equipment. Ground the unit as follows to

prevent interference:

• The ground wire should be 1.25 sq or larger.

• The ground wire should be as short as possible.

• The signal ground and frame ground are separated, however the power

line is not isolated. Therefore, do not connect the signal ground to the

frame ground when connecting other equipment to a positive ground

battery.

External equipment

The power supply port (IN/OUT port) is commonly used for connection of

external equipment such as navigation equipment or a PC. Refer to the

interconnection diagram on page S-1 for connection.

IN/OUT port

Connector Remarks

1TD-A

2TD-BIEC61162-1/NMEA 0183

3 RD-H

4 RD-C IEC61162-1/NMEA 0183

5+V

6GNDPower supply (12-

24VDC)

(INPUT)

7FG

AUX port

Connector Remarks

1TD-A

2TD-BIEC61162-1/NMEA 0183

3 RD-H

4 RD-C IEC61162-1/NMEA 0183

5 +Vout

6GNDMax 300 mA

(OUTPUT)

7FG

www.reelschematic.com

Other manuals for RD-30

Table of contents

Other Furuno Monitor manuals

Popular Monitor manuals by other brands

Linear Acoustic

Linear Acoustic LQ-1000 user guide

AOC

AOC I2579V user manual

Gateway

Gateway FPD1520 user guide

Asus

Asus VB171D - 17" LCD Monitor Service manual

Dell

Dell S2230MX Setting up

Philips

Philips 107C64 user manual

Dell

Dell S2409WFP user guide

EverFocus

EverFocus EN-7517E instruction manual

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Service manual

Dell

Dell Precision 7680 Connection guide

LG 50PM1M - - 50" Plasma Panel Service manual

Bosch

Bosch DDU 9 manual

Acer

Acer A231HL user manual

Philips

Philips 86BDL4152T user manual

NEC

NEC AccuSync LCD5V user manual

Emay

Emay SleepO2 user manual

IBM

IBM 6360 Product support manual

LG M1950D-PZ owner's manual