Fujitsu SCANPARTNER 600C User manual
ScanPartner 600C
Image Scanner
User’s Manual
Version 1.0
(Doc. No. 250-0062-0)
2
Table of Contents
1. INTRODUCTION ………………………………… 3-4
2. INSTALLATION AND CONNECTIONS ………. 5-13
2.1 Shipping Bracket ……………………………………………… 5
2.1.1 Removing the Shipping Bracket …………………………….. 5-6
2.1.2 Refitting the Shipping Bracket ………………………………. 7
2.2 SCSI Interface Device ID …………………………………….. 7-8
2.3 ADF Paper Chute ……………………………………………… 9
2.4 ADF Output Tray ……………………………………………… 10
2.5 Document Loading ……………………………………………. 11
2.6 ADF Scanning …………………………………………………. 12
2.7 Connecting the Cable …………………………………………. 13-14
3. MAINTENANCE ………….………………………. 15-17
3.1 Cleaning the ADF ……………………….…………………….. 15-16
3.2 Cleaning the Glass ……………………………………………. 17
4. TROUBLESHOOTING ……………….………….. 18-21
4.1 Question and Answer ………………………………………… 18-20
4.2 Paper Jam in the ADF ………………………………………… 20-21
5. SPECIFICATIONS ………….…………………….. 22
5.1 Model: ScanPartner 600C ………………………………….…. 23
3
1. INTRODUCTION
Congratulations on your purchase of a Fujitsu ScanPartner 600C Image Scanner.
Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you
with the proper instructions on how to unpack, install, operate and maintain the Scanner.
Figure 1-1 shows how the Scanner is packed. You can check all items against the “checklist”, included with your
Scanner.
4
Figure 1-1 - Scanner Packing
User Manual
Output Paper Tray
Image Scanner
Power Cable
Foam
Foam
Carton
5
2. Installation and Connections
Please unpack the Scanner carefully and check the contents against the “checklist”. If any items are missing or
damaged, please contact your authorised local dealer immediately.
Precautions:
vKeep the Scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause
damage to the unit.
vDo not install the Scanner in a humid or dusty place.
vBe sure to use the proper AC power source.
vPlace the Scanner securely on an even, flat surface. Tilted or uneven surfaces may cause mechanical
or paper-feeding problems.
vRetain the Scanner box and packing materials for shipping purposes.
2.1 Shipping Bracket
The Scanner has a bracket that locks the carrier mechanism for transportation purposes. This bracket must be
put into the use position before using the Scanner.
Note:
If the power is turned on before the bracket has been removed the PAPER JAM light will
turn on. Before proceeding, turn the power off, disconnect all cables and follow the
instructions below to remove the shipping bracket.
2.1.1 Removing the Shipping Bracket (refer to figures 2-1 and 2-2)
i) Carefully place the Scanner in an upright position on its front.
ii) Using a suitable screwdriver, remove the screw and pull out the shipping bracket.
iii) Put the shipping bracket into the use position with the short side extending into the scanner
base and secure it with the screw.
vi) Carefully place the Scanner back into its normal position.
6
Figure 2-1 - Removing the Shipping Bracket
Figure 2-2 - Securing the Shipping Bracket
Shipping Position
Use Position
7
2.1.2 Refitting the Shipping Bracket
Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket
to avoid causing damage to the Scanners’ internal mechanism. Please follow the instructions below
to refit the shipping bracket.
i) Turn off the Scanner power at the power on/off switch.
ii) Disconnect all cables.
Note: For steps (iii) to (vi) please refer to figures 2-1 and 2-2
iii) Carefully place the Scanner in an upright position on its front side.
iv) Using a suitable screwdriver remove the screw holding the shipping bracket in the use
position.
v) Put the shipping bracket into the shipping position, with the long side extending into the
Scanner base. Secure it with the screw.
vi) Carefully place the Scanner back into its normal position.
2.2 SCSI Interface Device ID
When you have several devices on a SCSI chain, you may need to adjust the SCSI ID selector setting located
on the back of the Scanner. This setting assigns a specific “device ID” to the Scanner. If the assignment
conflicts with an existing SCSI device, please select a new ID (see Figure 2.3).
Note: The factory setting for the Scanner is ID 6. Usually, ID 0 is assigned to an internal hard disk drive,
and ID7, to SCSI adapter or host. ID 8 and 9 are not in actual use.
Using a suitable tool, turn the selector switch until the arrow points to the desired ID number.
8
Figure 2-3 - Adjusting the SCSI ID Setting
SCSI ID Selector
9
2.3 ADF Paper Chute (Figure 2-4)
i) Raise the right side of the paper chute to about 45 degrees.
ii) Pull down the wire leg from under the paper chute •.
iii) Insert the wire leg into the grips on the document cover ‚.
iv) Pull out the paper chute extension to the length you want.
Figure 2-4 - Setting the ADF Paper Chute
ADF Paper Chute
Document Cover
10
2.4 ADF Output Tray (Figure 2-5)
i) Hold the output tray at an angle as shown in figure 2-5.
ii) Insert the three protrusions on the paper output tray to the three slots on the ADF •.
iii) Lower the paper tray gently ‚. Make sure the tray is firmly attached to the ADF.
iv) Pull out the output tray extension wire to the desired length.
Figure 2-5 - Install the ADF Output Paper Rack
Extensions
Other manuals for SCANPARTNER 600C
2
Table of contents
Other Fujitsu Scanner manuals
Fujitsu
Fujitsu ScanSnap fi-5110EOXM Manual
Fujitsu
Fujitsu ScanSnap fi-5110EOXM User manual
Fujitsu
Fujitsu fi-7300NX User manual
Fujitsu
Fujitsu fi-4530C User manual
Fujitsu
Fujitsu fi-6670 Series Manual
Fujitsu
Fujitsu SP-1130Ne Manual
Fujitsu
Fujitsu FI-6130 Configuration guide
Fujitsu
Fujitsu ScanSnap Organizer User manual
Fujitsu
Fujitsu ScanSnap S1100 User manual
Fujitsu
Fujitsu ScanSnap S1300 User manual
Fujitsu
Fujitsu fi-4750L User manual
Fujitsu
Fujitsu FI-400F Manual
Fujitsu
Fujitsu ScanPartner 620C User manual
Fujitsu
Fujitsu SCANPARTNER 600C User manual
Fujitsu
Fujitsu ScanSnap FI-4110EOX2 User manual
Fujitsu
Fujitsu ScanSnap fi-5110EOX User manual
Fujitsu
Fujitsu ScanSnap iX1600 Configuration guide
Fujitsu
Fujitsu S510M - ScanSnap - Document Scanner Manual
Fujitsu
Fujitsu Fi-5110EOX2 - ScanSnap! - Document Scanner User manual
Fujitsu
Fujitsu ScanSnap S300 User manual
