Francis Searchlights A6192 User manual

User Instruction & Installation Manual

L300 234w RF LED Searchlight

Product Reference Number:

A6192/A6188 –240v/24v Deck

A6193/A6189 –240v/24v Deck Pedestal

A6194/A6190 –240v/24v Cabin

A6195/A6191 –240v/24v Cabin Pedestal

Manufacturer’s details: Distributor details:

Manual Part Number: C27928

Issue: 2 14.8.19 EC1776

Francis Searchlights Ltd

Union Road, Bolton

Lancashire, BL2 2HJ, UK

Tel: +44 (0) 1204 558960

Fax: +44 (0) 1204 558979

http://www.francis.co.uk

E-mail: sa[email protected].uk

CONTENTS 
 
- Introduction 
 
- Safety Precautions 
 
- Technical Information 
 
- Unpacking and Installation Instructions 
 
- Electrical Installation 
 
- Operating Instructions 
 
- Fault Finding 
 
- Maintenance and Servicing 
 
- Wiring Diagrams & General Assemblies 
 
- Spare Parts List 
 
 Back To Top

1 –Introduction

It is imperative that this manual is read carefully and understood before

installing your equipment. For your future reference please keep this

manual in a safe place.

Thank you for specifying a product from the Francis Searchlights range. All Francis products

are designed to give complete customer satisfaction and are manufactured to the highest

engineering standards in order to ensure optimum performance and service life.

The Francis LED range combines features proven over many years service in the most

hazardous conditions in both marine and land installations.

In order to prolong the life and performance of your product, we recommend that you only

specify Francis Searchlights spare parts. This will also ensure that any warranties on your

equipment will not be invalidated. Information on spares ordering and parts is provided in this

manual.

Should you ever need to contact Francis Searchlights Ltd. regarding your equipment, please

quote the Product Serial Number at all times.

2 - Safety Precautions

The following instructions must be adhered to, in order to ensure a safe working environment

and the safety of the user.

Note: When unpacking or manoeuvring the searchlight into its fixing position, suitable

lifting points must be used in order to prevent damage to the equipment or personal

injury.

◼The high luminance of the LED can cause severe damage to the eye if viewed directly.

ALWAYS wear suitable protective goggles when viewing the LED;

◼Searchlights get hot. Never touch the unit when lit and always allow 15 to 20 minutes for

cooling down after turning the searchlight off;

◼Never place anything on or cover the searchlight when in use;

◼Ensure the LED has cooled sufficiently before removal;

◼Due to the vast range of LED modules available it may appear possible that more powerful

LED’s can be used in the equipment than for which it was designed. Even when the unit

will physically accept a higher wattage LED, this substitution is not recommended and is

dangerous. This action will also void any warranties on the equipment.

3 –Technical Information

This product has been designed to operate in accordance with the product specification.

The LED 300 searchlight has the following features:

◼All marine grade materials and fixings;

◼Powder coated finish;

◼Full 450° horizontal rotation;

◼Vertical movement ±40˚ (Deck & Deck Pedestal;

◼Vertical movement +30˚ to -25˚ (Cabin & Cabin Pedestal;

◼Instant re-strike. No cooling down time required;

◼Economical 20,000 hour LED life;

◼Toughened super clear Opti white front glass;

◼Precision made glass lenses;

◼Remote focus facility;

◼Sealing –IP56 Searchlight & Control Gear protected to IP66;

◼Searchlight weight Deck 17 Kgs, Deck Pedestal 21Kgs, Cabin 20Kgs, Cabin Pedestal

24Kgs & PSU weight 4 Kgs;

The searchlight also performs to the following optical data:

◼Supply voltage –24 to 240v;

◼Luminous flux 22,800;

◼Colour temperature 6000K;

◼Range –1876 metres;

◼Divergence –Spot 4° - Flood 10°;

◼Temperature range: -20 to +50

In order that the searchlight operates correctly it is imperative that competent personnel are

responsible for the installation, operation and servicing of this equipment. Failure to adhere to

this advice may cause premature failure or incorrect operation of the searchlight, which may

damage the equipment or cause personal injury.

4 - Unpacking and Installation Instructions

The following instructions should be read and fully understood prior to installing the equipment

to ensure that the correct procedures are followed, and all safety precautions are observed.

Note: If the equipment has been in storage for a considerable amount of time, it is

advisable to conduct a routine maintenance check on all parts before installation.

Safety Precautions

This equipment should not be connected to an electrical supply before being installed.

Installation procedures should be adhered to in order to ensure a safe working environment

and reduce the risk of damage or personal injury.

Preparing the Mounting Position

Mark out and drill the fixing holes through the deck. If anti-vibration mounts are to be fitted, the

fixing holes for the mounts should also be marked out and drilled. Prior to manoeuvring the

searchlight into its’ fixing position, the AV mounts should be fitted to the base. When in the

desired position, bolt the searchlight firmly down.

5 - Electrical Installation

For safety purposes, only competent personnel should perform the electrical installation. All

equipment should be installed to current Electrical Regulations and Standards.

In order to obtain the maximum light output from the searchlight, it is essential that the full

operating voltage of the LED fitted be applied to the LED contacts.

Method of Electrical Connection

1) Disconnect the supply before working on the electrical system;

2) The searchlight must be connected to a fused electrical supply, using suitably sized cable;

3) If the searchlight is located a considerable distance from the supply, provision must be

made in the cable size in order to overcome the voltage drop.

4) Whenever possible cable terminations should be made below deck and with approved

terminal devices;

5) If a spare auxiliary fuse or circuit breaker is not available, one of the correct type/rating

should be fitted and connected to a positive supply. It is advisable to locate a bus bar or

main connection and avoid any direct connection to the supply:

6) For 110/220v AC products, the following colour coding system should be used for the

customer supply cable:

Brown - Live

Blue - Negative

Green/Yellow - Earth

Installation Guideline

A typical installation and connection routine for the LED 300 searchlight is as follows:

Referring to wiring diagram C27877 HV or C27879 LV, a supply is fed into the on/off control

box, which then provides a common feed to the driver box & searchlight.

The following cables have been fitted as standard.

3 metres of 5 core 1.5mm cable from the control box to the driver box.

3 metres of 7 core 1.5mm cable from the searchlight to the driver box.

Cables required to be supplied by the customer: -

The Mains cable to the on/off Control box.

6 - Operating Instructions

This equipment is designed for use out of doors, in free air. Never place anything on or cover

the searchlight when in use as this may present a hazard.

The searchlight can be positioned using the pan and tilt lock wheels. When in the desired

position the lock wheels must be securely fastened to prevent damage.

The beam of the searchlight can be adjusted to give a variety of beam types. Using the yellow

remote focus button on the Control Box, the desired beam can be achieved for any particular

application. The beam will move continuously through ‘spot’ to ‘flood’. In order to fix the beam

type; simply release the button at the desired position.

Using the template provided mark out and drill the fixing holes through the deck or cabin roof.

In case of cabin control models, a centre hole is also required to allow the mechanism to pass

through.

On an uneven surface when bolting down the searchlight it is necessary to use a suitable

sealant, such as silicone, in order to ensure weather proofed joint.

Please note that if a heater is fitted, it is advisable to leave the heater permanently in the ‘ON’

position in order to remove any condensation. The heater specified on this equipment is self-

regulating and will shut off when the dew point temperature is reached.

This product should not be used for any purpose other than for which it was designed.

Any modifications to the product should not be undertaken without consulting the

manufacturer.

7- Fault Finding

All fault finding must be conducted by a competent person or qualified Electrical Engineer.

Failure of LED to light.

In the event of the LED failing to light the following steps should be taken:

1) Check that the mains supply is connected to the input of the LED driver and check all

connections as per the wiring diagram. On operation if the LED does not light, switch off

mains supply and check all fuses;

8 - Maintenance and Servicing

In order to prolong the service life and performance of your searchlight, the following

maintenance guidelines are recommended:

◼Maintenance checks should be conducted before every voyage or at least every three

months;

◼Before checking, disconnect the equipment from the supply;

◼Visually inspect the condition of the equipment;

◼Any major or minor structural damage should be rectified immediately in order to reduce

sympathetic wear;

◼After inspection it may be necessary to clean the inside of the searchlight. The following

procedure should be adhered to:

◼Remove the front bezel;

◼Clean the front glass inside and out using a proprietary glass cleaner;

◼Clean the lenses if required;

◼It is advisable to check all seals and gaskets for signs of degradation. Renew if necessary;

◼Upon completing all maintenance requirements, the searchlight should be tested for full

working order (approximately 20 minutes).

◼Every six months the external movement mechanisms i.e. lockwheels, elevation and pan

mechanisms, should be lightly lubricated.

If in any doubt as to the correct servicing procedures to adopt please contact your

distributor/agent or the manufacturer who will be able to advise the best course of

action for your product.

This manual suits for next models

Table of contents

Other Francis Searchlights Floodlight manuals

Francis Searchlights

Francis Searchlights A7138 User manual

Francis Searchlights

Francis Searchlights FH300 User manual

Francis Searchlights

Francis Searchlights L230RC User manual

Francis Searchlights

Francis Searchlights A7209 User manual

Francis Searchlights

Francis Searchlights A7195 VL500 150w 24v LED User manual

Francis Searchlights

Francis Searchlights L560 User manual

Francis Searchlights

Francis Searchlights A6074 User manual

Francis Searchlights

Francis Searchlights FR 230 Operation manual

Francis Searchlights

Francis Searchlights FR480 User manual

Francis Searchlights

Francis Searchlights Voyager 2 User manual

Francis Searchlights

Francis Searchlights FX380 User manual

Francis Searchlights

Francis Searchlights FB280 User manual

Francis Searchlights

Francis Searchlights A7123 User manual

Francis Searchlights

Francis Searchlights A2963 User manual

Francis Searchlights

Francis Searchlights FX380D User manual

Francis Searchlights

Francis Searchlights A6220 User manual

Francis Searchlights

Francis Searchlights A2277 User manual

Francis Searchlights

Francis Searchlights A7147 User manual

Francis Searchlights

Francis Searchlights A7164 User manual

Francis Searchlights

Francis Searchlights A6150 User manual

Francis Searchlights

Francis Searchlights L380 User manual

Francis Searchlights

Francis Searchlights A7120 User manual

Francis Searchlights

Francis Searchlights FH380RC User manual

Francis Searchlights

Francis Searchlights A7170 User manual

Popular Floodlight manuals by other brands

VIZULO

VIZULO Micro Martin Mounting instruction

EuroLite

EuroLite LED IP FL-100 SMD user manual

Cooper Wheelock

Cooper Wheelock XB12 specification

Allen + Roth

Allen + Roth 17624-000 user manual

ADJ

ADJ 4 STAGE PAK User instructions

Cooper Lighting

Cooper Lighting EGL91SW233 Specification sheet

Max

Max 37496 instruction manual

BEGA

BEGA 85 143 Instructions for use

Beamz

Beamz 151.226 user manual

EuroLite

EuroLite LED IP FL-8 user manual

Ledj

Ledj PERFORMER 36 RGB user manual

Perel

Perel ELS3 user manual

Perel

Perel ELS3WD user manual

LumX

LumX LM 36130 instruction manual

Xtricity

Xtricity 4-80053 instructions

Stahl

Stahl 6521/4 Series operating instructions

Ecosense

Ecosense EcoSpec installation manual

Ayrton

Ayrton minipanel FX manual