Foxconn FBH-302 User manual
PRODUCT NAME: BLUETOOTH HEADSET
TRADE NAME: FOXCONN, MODEL NO.: FBH-302
Manual
ChargingProcedure:
1.ConnecttheUSBchargingcableintotheUSBportofcharger.
2.Plug‐inthechargerintotheACoutlet.
3.Connectthechargertotheheadsetchargingport.ThentheredLEDindicated.
4.1sttimechargeshouldbeforatleast2hours.Oncethechargingcompletionthe
redLEDturnsoff.
5.ThereisanalternativechargingwaybyusingattachedUSBchargingcableto
connectthecomputerUSBportdirectly.
TurningtheHeadsetOn/Off:
1.Toturntheheadseton,pressMFB2secondsuntilthegreedLEDon.Thenrelease
MFBbutton.
2.Toturntheheadsetoff,pressMFB2secondswhilepoweringonuntiltheredLED
on.ThenreleaseMFBbutton.
Howeasytoweariton:
1.Inserttheearloopintotheheadset.
2.Weartheopensideofheadsetearloopfromthetopofearinplace.
3.Turntheheadsetearloopclockwiseorcounterclockwiseforfittingonleftorright
ear.
4.Alignthemicrophonewithyourmouthtogetthebestreceptionforthecaller.
PairingProcedure:
1.TurnontheBluetoothfeatureonyourphone.
2.Keeptheheadsetstatusatpoweroff
3.PressMFBbuttonformorethan4secondsuntilthegreenLEDflashedquickly.
4.PerformyourBluetoothphonetodiscovertheheadset.
5.Selectthe“FBH-302“headset.Ifpromptedforapasskey,enter0000.
6.Whenpairingissuccessful,theindicatoronyourheadsetflashesgreeneveryfive
seconds.Yourphonewillalsoconfirmwhenpairingiscomplete.
HeadsetControlsandIndicators
ControlActionKeyVisualIndicatorTone
PowerOn
PowerOff
ON:PressMFBbuttonfor
2seconds
Off:PressMFBbuttonfor
2seconds
On:GreenLEDon1
second
Off:RedLEDon1
second
4risingtones
4descending
tones
PairingPressMFBbuttonfor
morethan4seconds
GreenLEDflashes
100mscontinuouslyfor
3minutes
2risingtones
VoiceDialPressMFBbuttonless
than1second
None1beeptone
LastNumber
Redial
PressMFBbuttontwiceNone1beeptone
CallAnswerPressMFBbuttonless
than1second
None2risingtones
RejectPressMFBbuttontwiceNone2descending
tones
EndaCallPressMFBbuttonless
than1second
None1beeptone
Audio
Transfer
PressMFBbuttontwiceNone1beeptone
VolumeUp
Volume
Down
PressVolumeUpbutton
lessthan1secondfor
eachlevel
PressVolumeDown
buttonlessthan1second
foreachlevel
None
None
1beeptone
1beeptone
Standby
Mode
NoneGreenLEDon1second
every5seconds
ConnectedNoneGreenLEDon1second
only
1beeptone
DisconnectedNoneRedLEDon1second
only
ConnectableNoneGreenLEDon1second
every2seconds
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of
this device could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RF exposure warning ·
The equipment complies with FCC RF exposure limits set forth for an
uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any
other antenna or transmitter.
