Fluke 2063513 User manual

Model 16 English Instruction Sheet

Page

Multimeter with Temperature

Instruction Sheet

Read First: Safety Information

To ensure that the meter is used safely, follow these instructions:

•Do not use the meter if the meter or test leads appear damaged, or if

you suspect that the meter is not operating properly.

•Disconnect the live test lead before disconnecting the common test

lead.

•When using the probes, keep your fingers behind the finger guards on

the probes.

•Do not use the V•Check mode to measure voltages in circuits that

could be damaged by this mode's low input impedance

(≅2 kΩ).

•Turn off power to the circuit under test before cutting, desoldering, or

breaking the circuit. Small amounts of current can be dangerous.

•Do not apply more than 600V rms between a meter terminal and earth

ground.

•Use caution when working with voltages above 60V dc or 30V ac rms.

Such voltages pose a shock hazard.

PN 2063513 December 2002 Rev.1, 9/04

Model 16 English Instruction Sheet

Page

Symbols

Press button.

Press button to switch between modes.

Double insulation.

Manual ranging mode.

ip14i.eps

Automatic Range Selection

The meter defaults to autoranging when you turn it on. The 4000 mV

range can be entered only with manual range selection.

Manual Range Selection

MULTIMETER

OFF

600V

COM

CAT

To return to autoranging, press for

2 seconds, or change the measurement

mode.

ip15i.eps

Battery Saver



If the meter is ON but inactive and not connected to voltage for more than

45 minutes, the display goes blank to preserve battery life. To resume

operation, press any button.

Battery Saveris disabled in MIN/MAX record mode.

Model 16 English Instruction Sheet

Page

AC and DC Voltage

Also refer to V•Check.

Volts AC Volts DC

Input Impedance ≅5 MΩInput Impedance ≅10 MΩ

50 Hz to 400 Hz

MULTIMETER

OFF

600V

COM

CAT

AC / DC

DCAC

4000 mV 4V 40V 400V 600V

MULTIMETER

OFF

600V

COM

CAT

AC / DC

ip01i.eps

Resistance and Continuity

Turn off circuit power before testing. Also refer to V•Check.

Resistance Continuity

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

Check

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

Check

<25Ω

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

Check

Low Impedance

V¥Check

Short Open

ip02i.eps

Detects shorts and opens ≥250 µS.

Model 16 English Instruction Sheet

Page

•

Check

If a dc or ac voltage greater than about 4.5V is present across the inputs

when the meter is set to R, G, or e, the meter switches automatically

to dc or ac voltage mode (V•Check mode).

WWarning

Repetitive transients on a dc bus will cause V•Check to

select ac volts, even though a hazardous dc voltage may

be present. To avoid a misleading display and possible

electric shock, manually select the proper volts function

for measurements on these circuits.

When V•Check is activated, the meter has low input impedance (LoZ)

≅2 kΩ. This load can alter the voltages in electronic control circuits. Do

not use V•Check to measure voltage in circuits that could be damaged by

a 2 kΩload.

Hint: V•Check can be effectively used to eliminate “ghost” voltages.

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

If AC detected

If DC detected

Meter puts 2 kΩ

load on circuit.

Disable and re-enable V•Check

For , and Ω,

Disables V•Check and

locks meter in selected

mode.

2 sec

Re-enables

V•Check

ip09i.eps

Model 16 English Instruction Sheet

Page

Temperature

80BK

Integrated

Temperature

Probe (Type K)

Vent

Pipe

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

ip19f.eps

Note correct connector polarity.

To meet stated accuracy, the 80BK temperature adapter must be at the

same temperature as the meter.

WWarning

To avoid possible electric shock, DO NOT apply

thermocouple tip to any conductor that is greater than

30V AC, 42.4V pk, or 60V DC to earth.

Model 16 English Instruction Sheet

Page

Capacitance

Turn off circuit power; then disconnect and discharge the capacitor before

measuring capacitance.

If the capacitor requires more

discharging, diSC is displayed

while the capacitor discharges.

1 µF 10 µF 100 µF 10,000 µF

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

ip05i.eps

Note correct probe polarity for polarized capacitors.

Model 16 English Instruction Sheet

Page

Microamps

µA

Range 0 to 200 µA

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

Flame

sensor

probe

Control

module

µA AC µA DC

ip20i.eps

Example: Flame rectification circuit.

To measure flame rectification circuits:

1. Turn function switch to far right position.

2. Push select button 3 times to select µA.

3. Connect meter between flame sensor probe and control module.

4. Turn heating unit on and record µA measurement.

Model 16 English Instruction Sheet

Page

Diode Test

Turn off circuit power before testing. For best results diodes

should be measured out of circuit.

Also refer to V•Check.

Good Diode

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

Typical voltage

for silicon diode

Single beep

Low Impedance

V•Check

ip03i.eps

Forward Bias Reverse Bias

Bad Diode

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

MULTIMETER

OFF

600V

COM

CAT

TEMPERATURE

•

Check

ip04i.eps

Shorted Open

Model 16 English Instruction Sheet

Page

MIN MAX

µF

(Records the lowest and highest measurements)

V•Check, autoranging, and Battery Saverare disabled. Put the meter

in the proper range before entering MIN MAX.

When the reading changes more than about 50 digits, the meter gives a

short beep. When a new minimum or maximum is recorded, the meter

gives a long beep.

Present Reading with

Input Change Alert Maximum Reading

Minimum Reading To Exit

Enter

MIN MAX

2 sec

ip10i.eps

Model 16 English Instruction Sheet

Page

MIN MAX with Elapsed Time

µF

Records the hours and minutes between when MIN MAX was entered

and the last high and low was recorded. OL is displayed for times longer

than 99:59.

To enable the MIN MAX timer, hold down Mwhile turning the rotary

switch from OFF to either measurement mode.

Enter MIN MAX. View

Present Reading Maximum Reading Maximum Reading

Elapsed Time

Minimum Reading

Elapsed Time Minimum Reading Exit MIN MAX

2 sec

ip11i.eps

This manual suits for next models

Table of contents

Popular Multimeter manuals by other brands

Agilent Technologies

Agilent Technologies 34420A user guide

Hameg

Hameg HM 8012 manual

Mastech

Mastech MY70 Operation manual

Steren

Steren MUL-300 user manual

Somogyi Elektronic

Somogyi Elektronic home SMA 92 instruction manual

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 operating instructions

PeakTech

PeakTech 4000 Procedure of calibration

YOKOGAWA

YOKOGAWA 90050B user manual

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 operating instructions

Tempo Communications

Tempo Communications MM200 instruction manual

Elenco Electronics

Elenco Electronics CM-1555 operating instructions

Mastech

Mastech MS8238C user manual

SDAR

SDAR 830A, 830B, 830D, 830C user manual

RS PRO

RS PRO RS-9519BT instruction manual

BGS technic

BGS technic 8890 instruction manual

Amprobe

Amprobe Hexagon 60 user manual

Morris

Morris 57074 user manual

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter user guide