Fluke COMARK Diligence RF313-TH Guide
Part No: 20632-1 03/19 Page 1 of 3
Restart or Factory Reset a WiFi Device
This Help Guide refers to Diligence™ WiFi data loggers, including Sensors and Alert
How do I Restart or Reset my Diligence™ WiFi data logger?
Under normal circumstances, you do not need to reset your Diligence™ WiFi data logger. However
you may be instructed to do this by our support team to recover a Device which is not working
properly, or return it to its factory state.
Restart
Performing a Restart on the WiFi Sensor will restart the internal firmware, retaining all configuration
and network settings. The Sensor will disconnect from the wireless network, and immediately enter
a low power sleep mode. It can take up to 30 minutes for the Sensor to re-connect and synchronize
after a Restart. Under normal circumstances the Sensor will synchronize within 15 minutes. Once
communication is re-established the Sensor returns to its normal transmission rate. A Restart will
cause a new recording session to be started.
To perform a Restart...
What is this?
RF313-TH
From the Sensor Home screen
Press and hold the button for 10 seconds
Release when the LOW symbol starts to flash.
All other Sensor types
RF311-T, RF312-TP, RF312DualPlus,
RF312Glycol, RF314-TC, RF314Dual
From the Sensor Home screen
Press and hold the button for 10 seconds
Release when the LCD shows
Part No: 20632-1 03/19 Page 2 of 3
Restart or Factory Reset a WiFi Device
Factory Reset
Performing a Factory Reset on the WiFi Sensor will clear all internal configuration and network
settings. The Sensor will disconnect from the wireless network, and all WiFi activity is stopped. When
you want to use your Sensor again, you’ll need to connect the Sensor to a wireless network and re-
configure it using the WiFi Sensor Software.
You should perform a Factory Reset prior to shipping the Sensor or before storage.
To perform a Factory Reset...
RF313-TH
From the Sensor Home screen
Press and hold the button for 20 seconds
Release when the LCD shows
WiFi-AL (Alert)
Press and hold the button for 10 seconds
Release when the LEDs start to cycle.
Part No: 20632-1 03/19 Page 3 of 3
Restart or Factory Reset a WiFi Device
All other Sensor types
RF311-T, RF312-TP, RF312DualPlus,
RF312Glycol, RF314-TC, RF314Dual
From the Sensor Home screen
Press and hold the button for 20 seconds
Release when the LCD shows
RF324 Alert
Press and hold the button for 20 seconds.
The LEDs will cycle. When the LEDs go out, release the
button.
This manual suits for next models
7
Table of contents
Other Fluke Data Logger manuals
Fluke
Fluke 2638A User manual
Fluke
Fluke 1742 User manual
Fluke
Fluke 1730/BASIC Instruction manual
Fluke
Fluke 1734 User manual
Fluke
Fluke 1742 User manual
Fluke
Fluke 1742 User manual
Fluke
Fluke 2680A User manual
Fluke
Fluke COMARK RF400 User manual
Fluke
Fluke 1745-BASIC User manual
Fluke
Fluke DATAPAQ XDL12 User manual
Fluke
Fluke FL1730-BAS User manual
Fluke
Fluke 1743 User manual
Fluke
Fluke Datapaq TP3 User manual
Fluke
Fluke VIBXPERT EX Manual
Fluke
Fluke 1750 User manual
Fluke
Fluke 1738/B User manual
Fluke
Fluke 1732 User manual
Fluke
Fluke 1730/BASIC User manual
Fluke
Fluke VIBXPERT 3 User manual
Fluke
Fluke VR1710 User manual
