Fluke Comark RF300 Series User manual
The Professionals’ Choice
Comark Instruments
52 Hurricane Way, Norwich, Norfolk, NR6 6JB, UK
Tel: +44 207 942 0712
www.comarkinstruments.com
Comark Instruments
PO Box 500, Beaverton, OR 97077, USA
Tel (503) 643 5204
www.comarkUSA.com
RF300 –Help with Restart or Factory Reset
Issue 3 –03/01/2017
This help document refers to the RF300 Diligence WiFi Data Loggers, including the
RF324 Alarm Unit.
How do I Restart or Reset my RF300 Diligence WiFi device?
Under normal circumstances, you do not need to reset your RF300 Diligence WiFi Device. However, you may be
instructed to do this by our support team to recover a Device which is not working properly, or return it to its
factory state.
Restart
Performing a Restart on the WiFi Sensor will restart the internal firmware, retaining all configuration and
network settings. The Sensor will disconnect from the wireless network, and immediately enter a low power
sleep mode. It can take up to 30 minutes for the Sensor to re-connect and synchronize after a Restart. Under
normal circumstances the Sensor will synchronize within 15 minutes. Once communication is re-established the
Sensor returns to its normal transmission rate. A Restart will cause a new recording session to be started.
To perform a Restart...
RF313-TH
From the Sensor Home screen
Press and hold the button for 10 seconds
Release when the LOW symbol starts to flash.
Page | 2
Factory Reset
Performing a Factory Reset on the WiFi Sensor will clear all internal configuration and network settings. The
Sensor will disconnect from the wireless network, and all WiFi activity is stopped. When you want to use your
Sensor again, you’ll need to connect the Sensor to a wireless network and re-configure it using the WiFi
Sensor Software.
You should perform a Factory Reset prior to shipping the Sensor or before storage.
To perform a Factory Reset...
All other Sensor types
RF311-T, RF313-TP, RF314-TC
From the Sensor Home screen
Press and hold the button for 10 seconds
Release when the LCD shows rSt
RF313-TH
From the Sensor Home screen
Press and hold the button for 20 seconds
Release when the LCD shows FA
rS
RF324 (Alarm)
Press and hold the button for 10 seconds
Release when the LEDs start to cycle.
Page | 3
End.
All other Sensor types
RF311-T, RF313-TP, RF314-TC
From the Sensor Home screen
Press and hold the button for 20 seconds
Release when the LCD shows FArS
RF324 (Alarm)
Press and hold the button for 20 seconds.
The LEDs will cycle. When the LEDs go out, release the
button.
This manual suits for next models
5
Table of contents
Other Fluke Data Logger manuals
Fluke
Fluke 1730/BASIC User manual
Fluke
Fluke 1743-BASIC User manual
Fluke
Fluke 1730/US User manual
Fluke
Fluke VIBXPERT EX Manual
Fluke
Fluke 1742 User manual
Fluke
Fluke VIBXPERT 3 User manual
Fluke
Fluke 1735 User manual
Fluke
Fluke 1738 User manual
Fluke
Fluke VR1710 Instruction manual
Fluke
Fluke 1750 Instruction manual
Fluke
Fluke 1750 User manual
Fluke
Fluke 1730/BASIC Instruction manual
Fluke
Fluke 1742 Manual
Fluke
Fluke 1742 User manual
Fluke
Fluke 2680A User manual
Fluke
Fluke Datapaq TP3 User manual
Fluke
Fluke 1745-BASIC User manual
Fluke
Fluke VIBXPERT II User manual
Fluke
Fluke 1738/B User manual
Fluke
Fluke 1745 User manual
