Flashforge Finder User manual
SZ05-ZN/EN-A10
P14
01
4. You will see Quick Start Guide, After-sales
Service Card, Power Cable, Filament Guide
Tube and Tool Bag.
5. Use scissors to cut the four buckles that hold
the rods in place.
02
6. Discard the blue tape that holds the flat cable
in place. Be careful with the flat cable.
9. Remove the bottom insert. Power adapter,
USB cable and solid glue are packed inside.
10. Remove the two yellow buckles that hold the
Z-axis guide rods.
03
1. Filament Cartridge
04
05
Filament Outlet
Filament Guide Tube
Please pay attention to
loading direction!
4. After filament goes through guide tube, press
spring presser on the left side of extruder, and
insert filament vertically into filament intake to
the bottom.
1. Filament cartridge is at the back of printer. Before taking out filament cartridge, please hold the
clip on the top and take filament cartridge out.
2. Take out filament, tear off vacuum packing and put it into filament cartridge. Put filament through
filament outlet as the picture shown on the top left.
3. Hold clip on the top of filament cartridge, put
filament catridge back to the printer, and put
filament through filament guide tube.
Attention: filament unwinding direction should keep pace with the picture, or causing cannot
print properly.
Press here Filament intake
06
5. After inserting into filament intake, insert
guidetube into extruder filament intake.
6. Finally put the other end of filament guidetube
to filament outlet on the top of filament
cartridge.
7. Conmect the power adapter with the power cable. 8. Insert the power supply into the power input
on the back.
10. Press the touch screen button to turn on
the printer.
Touch Screen Button
9. Plug the other end of power cable into socket,
turn on the power switch.
07
04
How to use the nuts
Rotate the nuts clockwise
Raise the build plate to reduce the distance
between the nozzle and build plate.
Lower the build plate to increase the distance
between the nozzle and build plate.
Rotate the nuts Anticlockwise
Build plate goes up Build plate goes down
Leveling Build Plate
1. Tap [Tools].
Build
2. Tap [Level].
Berfore leveling, let's learn the funciton of nuts.
02
03
01
08
Screw the three nuts under the platform
counterclockwise until they are tight,
then tap the [OK] button.
3. Please wait while the extruder and platform finish initial movements. Screw three nuts under the
platform anticlockwise, then tap [OK] button.
Attention: three nuts may be tightened up before going out, please skip this step if you find
three nuts have been tightened up, and continue to following steps
4. After tapping [OK] button, the extruder will
move towards the first point and the plate will
move up and down to verify the distance
between nozzle and plate.
5. If the distance between the nozzle and plate
is too large, rotate the three nuts underneath
the platform clockwise for the same rounds
until you hear a steady beep.
Turn all three nuts under the platform
clockwise equally until
you hear the beep.
6. Tap the [Verify] button to check whether the
distance is appropriate.
7. If the distance is appropriate, tap [ok] to next
step. If the diastance still not appropriate,
please follow the prompts on the touch screen
to adjust till you see [ok].
Tap the [OK] button to move to
the next leveling point.
Congartulations
09
8. After first leveling point completed, start the other two leveling points.
Attention: when starting the second and the third leveling points, just need to adjust one
corresponding nut under extruder.
10. If the distance is appropriate, tap [ok] to next
step. If the diastance still not appropriate,
please follow the prompts on the touch
screen to adjust till you see [ok].
Tap the [OK] button to move to
the next leveling point.
Congartulations
11. Start the third leveling point according to the
method of the second leveling point.
After leveling completed, tap return arrow to
go back to home screen.
Leveling completed!
Finish
9. Follow the prompts on the touch screen to adjust the corresponding nut till you hear a steady
beep.
Turn the corresponding nut under
the platform clockwise until
you hear the beep.
Distance Too Small
Turn the corresponding nut under
the platform anticlockwise until
you hear the beep.
Other manuals for Finder
8
Table of contents
Other Flashforge 3D Printer manuals
Flashforge
Flashforge Finder User manual
Flashforge
Flashforge Inventor User manual
Flashforge
Flashforge Adventurer 3 Pro 2 User manual
Flashforge
Flashforge Creator 3 Pro User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge Waxjet 400 User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge DREAMER User manual
Flashforge
Flashforge Inventor II User manual
Flashforge
Flashforge Guider IIs User manual
Flashforge
Flashforge Inventor II User manual
Flashforge
Flashforge THOR500T User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge Guinder II User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge DREAMER User manual
Flashforge
Flashforge AD1 User manual
Flashforge
Flashforge DREAMER User manual
