Flashforge Creator 3 User manual

Creator3 加热组件更换操作文档

Creator 3 Heating assembly replacement operation

以下说明以右喷头更换加热组件为例，左喷头操作同理。

Here takes the right extruder as an example to replace the heating assembly, and the operation

of the left extruder is the same.

1. 右喷头进行退丝，退丝完成后拔出白色导丝管。

1. Unload the filament with [unload] function,and pull out the filament guide tube.

2. 机器关机。

2.Power off the machine.

3. 拧下喷头罩固定螺丝后，将喷头罩拆下，放在一边。

3.Unscrew the screw on the extruder cover,remove it and put it aside.

4. 拧下下图红色箭头处的 2个加热组件固定螺丝，并保存好螺丝。

4.Unscrew the 2 screws which fixing the heating assembly,and save the screws well.

5. 剪断线束固定扎带，根据红色箭头所示，拆下加热管线和热电偶线，这样，就能将旧加

热组件移除。

5.Cut off the tie, and remove the cables of heating cartridge and thermocouples as shown by

the red arrow in the picture below, then the old heating assembly can be removed.

6. 确保机器下图红框内的压电片上盖和下盖固定在原来位置，如掉落，需先将压电片上盖

和下盖安装好。（特别是旧版的压电片下盖，不要遗失）

6.Make sure that the upper and lower covers of the piezoelectric sensor are fixed in their

original positions,which show in the red frame in the picture below .If fall, please install them

back.(especially the old version of the lower cover, don't lose it)

7. 将新的加热组件安装到喷头安装座上。建议先装右边的螺丝，再拧左边的螺丝。

7.Install the new heating assembly on the extruder holder. It is recommended to install the

screw on the right first, and then tighten the screw on the left.

8. 将加热管线和热电偶线重新安装到喷头 PCB 板上，确保安装牢固。线束用扎带重新绑好。

8.Insert the cables of heating cartridge and thermocouple on the extruder PCB board again,

ensure that the connections are well. Re-tie the cables with a tie.

9. 重新将喷头罩装回去，拧紧螺丝。

9.Reinstall the extruder cover and tighten the screws.

10. 开机，进行喷头预热，确认更换后的加热组件能正常加热。

10.Turn on the machine, preheat the nozzle, and confirm that the new heating assembly can

heat up correctly.

Other manuals for Creator 3

3

This manual suits for next models

1

Table of contents

Other Flashforge 3D Printer manuals

Flashforge

Flashforge Guider 3 Plus User manual

Flashforge

Flashforge Creator Pro 2 User manual

Flashforge

Flashforge THOR500T User manual

Flashforge

Flashforge Creator Pro User manual

Flashforge

Flashforge Waxjet 400 User manual

Flashforge

Flashforge Finder User manual

Flashforge

Flashforge Guider II User manual

Flashforge

Flashforge Creator Pro Installation and maintenance instructions

Flashforge

Flashforge Hunter User manual

Flashforge

Flashforge Guinder II User manual

Flashforge

Flashforge Inventor User manual

Flashforge

Flashforge Creator 3 Pro User manual

Flashforge

Flashforge Invertor II User manual

Flashforge

Flashforge Creator 3 User manual

Flashforge

Flashforge Inventor II User manual

Flashforge

Flashforge Inventor User manual

Flashforge

Flashforge Creator 4 User manual

Flashforge

Flashforge CN/EN-A01 User manual

Flashforge

Flashforge Finder Installation and maintenance instructions

Flashforge

Flashforge Creator Pro User manual

Flashforge

Flashforge Creator Pro User manual

Flashforge

Flashforge Adventurer 5M User manual

Flashforge

Flashforge Creator 3 Pro User manual

Flashforge

Flashforge Creator3 User manual

Popular 3D Printer manuals by other brands

Ultimaker

Ultimaker S5 Material Station installation guide

EcubMaker

EcubMaker TOYDIY quick start guide

AnyCubic

AnyCubic Kossel Plus Modification

ReDeTec

ReDeTec ProtoCycler Operation manual

Kywoo3D

Kywoo3D Tycoon IDEX user manual

CraftBot

CraftBot PLUS PRO user guide

3DGence

3DGence INDUSTRY F340 user manual

HP

HP Jet Fusion 4200 Product Documentation Site Preparation Guide

Rokit

Rokit AEP Series user manual

AnkerMake

AnkerMake M5 user manual

DIYElectronics

DIYElectronics PRUSA I3 ELECTRONICS AND SOFTWARE GUIDE

Ackuretta

Ackuretta FreeShape 120 user manual

LONGER

LONGER LK5Pro manual

Stratasys

Stratasys J850 user guide

MakerBot

MakerBot Replicator user manual

Stratasys

Stratasys FDM Vantage Series user guide

ZYYX

ZYYX Pro II user manual

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Startup guide