Flashforge Creator 3 Pro User manual
快速启动指南
Creator 3 Pro / 金刚狼3 Pro
Quick Start Guide
EN/CN/DE/FR/한-A01
本手册仅适用于闪铸科技 金刚狼3 Pro 3D打印机
This guide is only applicable to FLASHFORGE Creator 3 Pro 3D printer
EN P01 / CN P09 / DE P17 / FR P25 / 한 P33
WARNING
注意事项
1. Hot! Avoid touching the heating nozzle and heating build plate in
operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。
Creator 3 Pro Quick Start Guide
Creator 3 Pro Introduction
01
3
4
10
12 13 14
11
5
6
7
8
9
21
1. Touch screen
2. USB disk port
3. Right extruder
4. Left extruder
5. Nozzle brush
6. Build plate
7. Leveling nut
8. Filament holder cover
9. Filament holder cover handle
10. Wind guide nozzle
11. Nozzle
12. Ethernet port
13. Power switch
14. Power cord entry
Packing List
02
Creator 3 Pro Filament Quick Start Guide After-sales
service card
Power cord
Unclogging pin tool
Lubricating grease PVP glue stick
Stamping wrench Cross screwdriver
Allen wrench
USB disk Leveling card
PTFE tube
Scraper
快速启动指南
Creator 3 Pro 金刚狼3 Pro
Quick Start Guide
EN/CN/DE/FR/한-A01
本手册仅适用于闪铸科技 金刚狼3 Pro 3D打印机
This guide is only applicable to FLASHFORGE Creator 3 Pro 3D printer
EN P01 / CN P09 / D E P17 / FR P2 5 / 한 P33
WARNING
注意事项
1. Hot! Avoid touching the heating nozzle and heating build plate in
operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。
03
Precautions for Unpacking the Equipment
4. Remove the buckles on the X-axis and Y-axis synchronous belts.
1. Take out the top accessories and pearl cotton.
2. Remove the tape from the machine.
3. Take out the internal pearl cotton block.
6. Press and hold [Z-] continuously until the build plate rises to a higher position, and
then take out the foam block below.
5. Connect the printer to the power supply, after power on, and then click [Tools] and
[Manual] in turn on the touch screen to enter the manual control interface.
04
1. Open the filament holder cover.
2. Take out the filament and insert it
into the filament feeding inlet.
Filament
intake
3. Attention: To facilitate smooth rotation of the filament, please install the filament in
the direction shown in the figure.
When installing the left-side filament, please make it run in the counterclockwise
direction;
When installing the right-side filament, please make it run in the clockwise direction.
Filament Loading
Preparation for Printing
05
4. Insert the filament into the filament
feeding inlet continuously until the filament
goes through the filament guide tube.
5. Press the filament feeding pressing plate
in front of the extruder, insert the filament
vertically into the extruder until it can't be
inserted any further, and then loosen the
filament feeding pressing plate.
6. Insert the filament guide tube into the
filament inlet hole on the extruder to fix.
7. Finally, fix the filament spool on the
filament spool holder and close the cover.
06
8. Filament feeding operation: Click the [Tools]-[Filament] button on the screen in turn,
and set a reasonable heating temperature according to the required temperature value
of the material; Operate according to the screen prompts, and wait for the nozzle to
extrude uniform filament smoothly.
Filament unloading operation: Click [Unload], press down the filament pressing plate
after the extruder temperature heating is completed, pull out the white filament guide
tube, and pull out the filament upward quickly and then filament unloading is completed.
Push filament
down through
for 3 seconds
Withdraw
Filament
Guidetube
Press here
07
9-point leveling function: when the printing flatness is still poor after the platform
leveling and XY/Z axis calibration, this function can be used to compensate for better
flatness;
Manual leveling mode: Execute platform leveling, Z-axis calibration and X, Y axis
calibration in turn. This is a complete set of leveling and calibration operation procedures.
The equipment has been leveled and calibrated before leaving factory. However, the
leveling plane may be damaged due to the vibration generated during transportation. It
is recommended to perform leveling before the first printing. There are two leveling
modes: auxiliary leveling mode and manual leveling mode. In the auxiliary leveling
mode, all execution will be completed with the help of the extruder sensor and auxiliary
prompts. When the function option is in the manual mode, the platform leveling in the
auxiliary mode will not activate the sensor function.
In total, the equipment contains the following leveling calibrations: Platform Leveling,
Calibration XY, Calibration Z and Auto level;
Please operate in the following order:
1. Click [Tools] and [Level Calibration] on the touch screen;
2. Select the auxiliary mode for leveling and calibration;
3. The extruder sensor calibration has been set before leaving factory, so there is no need
to operate again; Click platform leveling and operate following the prompts on the
screen;
4. Perform Z-axis calibration and operate following the prompts on the screen;
5. The X, Y axis have been calibrated before leaving factory, so there is no need to
operate again;
6. The whole leveling and calibration is completed.
Leveling and Calibration
08
Before the first printing, please complete the leveling, loading and calibration correctly
under the guidance of the quick start guide.
1. Tap [Print]. 2. Tap [Local memory] to choose print files.
3. Choose the preset print file [pavilion.gx].
5. The printer starts to heat up and will start printing after heating completed.
First Print
4. Tap [Print].
Other manuals for Creator 3 Pro
1
This manual suits for next models
1
Table of contents
Languages:
Other Flashforge 3D Printer manuals
Flashforge
Flashforge Waxjet 400 User manual
Flashforge
Flashforge DREAMER User manual
Flashforge
Flashforge Invertor II User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge Cura Manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge DREAMER User manual
Flashforge
Flashforge Finder User manual
Flashforge
Flashforge ADVENTURER 3 User manual
Flashforge
Flashforge Guider User manual
Flashforge
Flashforge ADVENTURER 3 User manual
Flashforge
Flashforge Adventurer 3 Pro 2 User manual
Flashforge
Flashforge DREAMER User manual
Flashforge
Flashforge Adventurer 5M Pro User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge Creator Pro User manual
Flashforge
Flashforge Finder User manual
Flashforge
Flashforge Adventurer 5M Pro User manual
Flashforge
Flashforge Finder User manual
Flashforge
Flashforge AD1 User manual
