Flash F7100443 User manual
LED PAR 28x10W
RGBW ZOOM
User Manual
Instrukcja Obsługi
Art No F7100443
SERIES: DJ
CONTENTS
EN
PL
INTRODUCTION 3
SAFETY INFORMATION 3
PRODUCT INFORMATION 4
INSTALLATION 4
CONNECTION 5
DMX CHART 8
WARNING! Use clamp to rig the xture.
WARNING! When clamping the xture to a truss or other structure at
any other angle than with the yoke hanging vercally downwards, use two
clamps of half-coupler type. Do not use any type of clamp that does not
completely encircle the structure when fastened.
WARNING! Posion or shade the bar so that the front lens will not be
exposed to sunlight or any other strong light source from any angle - even
for a few seconds. See Figure 1. The LED PAR lens can focused the sun’s
rays, creang a potenal re hazard and causing damage.
IMPORTANT! Do not point strong light output from other xtures at the
LED PAR, as intense illuminaon can damaged the display.
Figure 1.
2
Pages: 2-9
Strony: 10-16
INTRODUCTION
SAFETY INFORMATION
THANK YOU FOR PURCHASING LED PAR. FOR SAFETY REASONS
AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY
READ THE INSTRUCTIONS.
Please keep this User Manual
for future consultaon. If you sell
the xture to another user, be sure
that they also receive this instruc-
on booklet.
Unpack and check carefully the-
re is no transportaon damage be-
fore using the xture.
Before operang, ensure that
the voltage and frequency of po-
wer supply match the power
requirements of the xture.
It’s important to ground the
yellow/green conductor to earth
in order to avoid electric shock.
Disconnect main power before
servicing and maintenance.
Use safety chain when xes this
xture. Don’t handle the xture by
taking its head only, but always by
taking its base.
Maximum ambient temperature
is: 40°C Don’t operate it where the
temperature is higher than this.
In the event of serious ope-
rating problem, stop using the
fixture immediately. Never try
to repair the fixture by your-
self.
Repairs carried out by unskil-
led people can lead to damage
or malfunction. Please contact
the nearest authorized techni-
cal assistance center. Always
use the same type spare parts.
Do not connect the device
to any dimmer pack.
Do not touch any wire during
operation and there might be a
hazard of electric shock.
To prevent or reduce the risk
of electrical shock or fire, do
not expose the fixture to rain
or moisture.
The housing must be repla-
ced if they are visibly damaged.
Do not look directly at the li-
ght spot while the fixture is on.
3
PRODUCT INFORMATION
INSTALATION
Light Source:
28x10W 4in1 RGBW LEDs
Power consumpon: 200W
Power supply voltage:
90-260V, 50/60Hz AC
Macros (CTO, CTB,
2800-8000K)
Zoom 12°-60°
Operang modes: DMX512,
Manual, Auto, Sound-controlled,
Master/Slave, Sound acve,
DMX channel mode
13/29/55/07
IP Rang: IP20
Housing made: ABS
Cooling: Acve
AC IN/OUT: powerCon
3-Pin XLR DMX Input/Output
Net Weight: 3 kg
Gross weight: 3,5 kg
Net Dimensions:
H(14)xW(22)xD(27) cm
Pack Size:
H(31)xW(20)xD(33) cm
The unit should be mounted via
its screw holes on the bracket.
Always ensure that the unit is
firmly fixed to avoid vibration
and slipping while operating.
Always ensure that the structu-
re to which you are attaching
the unit is secure and is able
to support a weight of 10 ti-
mes of the unit’s weight. Also
always use a safety cable that
can hold 12 times of the we-
ight of the unit when installing
the fixture. The equipment must
be fixed by professionals. And it
must be fixed at a place where is
out of the touch of people and
has no one pass by or under it.
The fixture may be installed in
any orientation, but if installed
horizontally with a downward
4
beam-angle, water can poten-
tially pool in the fan wells. Under
normal operation the moisture
will evaporate. However, in loca-
tions with high rainfall, you may
wish to fabricate a rain shield
above the fixture, or modify the
position and orientation of the
fixture to minimize pooling.
Two quarter-turn brackets are
supplied with the fixtre if it is
to be flown above the ground.
Rig the fixture to a support truss
or structure using the supplied
brackets and suitable clamps.
Fasten a safety cable between
the support structure and the
attachment point on the fixture.
The safety cable must be able to
bear at least 10 times the weight
of the fixture.
CONNECTION
The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3-pin socket
2. Power (in/out): powerCON socket
The connecon is performed using cable with
XLR-female -> XLR-Male plugs.
1
3
22
SHIELD
SIGNAL (+)
SIGNAL (-)
3
1
FEMALE
XLR
MALE
XLR
1
SHIELD
SIGNAL (+)
SIGNAL (-)
FEMALE
XLR
MALE
XLR
2
3
4
5
1
2
3
45
CAUTION! At the last xture, the
DMX signal has to be terminated
with a terminator. Solder a 120Ω
resistor between signal (-) and si-
gnal (+) into a XLR plug and plug
it in the DMX output of the last
xture.
3-PIN XLR
5-PIN XLR
5
The package includes:
❶ - LED PAR (1 pc)
❷ - Power cable type
powerCON (1 pc)
❸ - Omega bracket (1 pc)
❹ - IR Remote (1 pc)
❺ - User Manual (1 pc)
❶
❷
❸
❹
User
Manual
❺
Using lamp, the change rate of power voltage should be within ±10%,
if the voltage is too high, it will shorten the light’s life.
Input Voltage Frequency Total Power
90-260[V] AC 50/60[Hz] 200[W]
Voltage Specicaon.
6
Control Menu
Diagram of connecon of devices by DMX cable.
IMPORTANT! The maximum number of devices connected
in series via power cable is 5 pcs.
The connecon is performed using power cable with powerCON con-
nector (included). The device must be operated by qualied personnel.
CAUTION! In the case of cable damage do not aempt to repair. Repla-
cement or repair can be made only on the manufacturer or by a person
with appropriate permissions
MENU
UP DOWN ENTER
DISPLAY
DMX
Controller DMX 512 DMX 512 120
Ω
7
DMX CHART
MENU DESCRIPTION
MODE
ADDR 001~XXX DMX address seng
AUTO IP1~8
ALON/(AU-A) SP_1 ~ SP_5
(Speed) Internal program (Alone)
MAST/(AU-M) SP_1 ~ SP_5
(Speed) Auto run (Master)
SOUN IP1~8 ALON /(SO-A) Sound control (Alone)
MAST /(SO-M) Sound seng (Master)
CH CH13/CH29/CH55/CH07 DMX Ch Mode seng
SET
MIC M-XX Mic sensivity seng
CURV LINR/SQUE/IN-S/SCUR Dimmer curve seng
LODA ON/OFF Reload data
VER V1.00 Soware version
CALI Code (Password: 088) Input password
CH01~CH06 Calibraon
REST ON/OFF Motor reset
MANU
DIMM 000-255 Dimmer set
Manual channel Control
STRB 000-255 Strobe set
RED 000-255 Red set
GREE 000-255 Green set
BLUE 000-255 Blue set
WHIT 000-255 White set
ZOOM 000-255 Zoom set
COLO 000-255 Color macro
CTO 000-255 Color Temp
TEMP TXXX Current temperature
DMX CH
Mode 1
DMX CH
Mode 2
DMX CH
Mode 3
DMX CH
Mode 4
DMX
Value Funcon
1 1 1 1 0-255 Dimmer (intensity from 0% to 100%)
2 0-255 Dimmer ne
2 2 3 2
Shuer/ strobe
0-31 Shuer closed
32-63 Shuer open
64-95 Strobe-effect from slow to fast (1-25 Hz)
96-127 Shuer open
128-143 Opening pulse in sequences from slow to fast
144-159 Closing pulse in sequences from fast to slow
160-191 Shuer open
192-223 Random strobe-effect from slow to fast
224-255 Shuer open
3 3 4 3 0-255 Red (intensity from 0% to 100%)
5 0-255 Red ne
4 4 6 4 0-255 Green (intensity from 0% to 100%)
7 0-255 Green ne
8
DMX CH
Mode 1
DMX CH
Mode 2
DMX CH
Mode 3
DMX CH
Mode 4
DMX
Value Funcon
5 5 8 5 0-255 Blue (intensity from 0% to 100%)
9 0-255 Blue ne
6 6 10 6 0-255 White (intensity from 0% to 100%)
11 0-255 White ne
7 7 12 7 0-255 Zoom (from max. to min.beam angle)
13 4 0-255 Zoom ne
8 14 0-255 Red zone 1 (intensity from 0% to 100%)
15 0-255 Red zone 1 ne
9 16 0-255 Green zone 1 (intensity from 0% to 100%)
17 0-255 Green zone 1 ne
10 18 0-255 Blue zone 1 (intensity from 0% to 100%)
19 0-255 Blue zone 1 ne
11 20 0-255 White zone 1 (intensity from 0% to 100%)
21 0-255 White zone 1 ne
12 22 0-255 Red zone 2 (intensity from 0% to 100%)
23 0-255 Red zone 2 ne
13 24 0-255 Green zone 2 (intensity from 0% to 100%)
25 0-255 Green zone 2 ne
14 26 0-255 Blue zone 2 (intensity from 0% to 100%)
27 0-255 Blue zone 2 ne
15 28 0-255 White zone 2 (intensity from 0% to 100%)
29 0-255 White zone 2 ne
16 30 0-255 Red zone 3 (intensity from 0% to 100%)
31 0-255 Red zone 3 ne
17 32 0-255 Green zone 3 (intensity from 0% to 100%)
33 0-255 Green zone 3 ne
18 34 0-255 Blue zone 3 (intensity from 0% to 100%)
35 0-255 Blue zone 3 ne
19 36 0-255 White zone 3 (intensity from 0% to 100%)
37 0-255 White zone 3 ne
20 38 0-255 Red zone 4 (intensity from 0% to 100%)
39 0-255 Red zone 4 ne
21 40 0-255 Green zone 4 (intensity from 0% to 100%)
41 0-255 Green zone 4 ne
22 42 0-255 Blue zone 4 (intensity from 0% to 100%)
43 0-255 Blue zone 4 ne
23 44 0-255 White zone 4 (intensity from 0% to 100%)
45 0-255 White zone 4 ne
9
DMX CH
Mode 1
DMX CH
Mode 2
DMX CH
Mode 3
DMX CH
Mode 4
DMX
Value Funcon
8 24 46
0-255 Macro Color
0-15 No Funcon
16-31 Red
32-47 Green
48-63 Blue
64-79 White
80-95 Red+Green
96-111 Red+Blue
112-127 Red+White
128-143 Green+Blue
144-159 Green+White
160-175 Blue+White
176-191 R+G+B
192-207 R+G+B+W
208-212 2700K
213-217 3200K
218-222 3500K
223-227 5000K
228-232 5500K
233-237 6000K
238-242 6500K
243-247 7000K
248-255 8000K
9 25 47
Color Temp
0-15 No Funcon
16-45 Below 3200K
46-75 3200K - 3500K
76-105 3500K - 5000K
106-135 5000K - 5500K
136-165 5500K - 6000K
166-195 6000K - 6500K
196-225 6500K - 7000K
226-255 7000K - 8000K
10
DMX CH
Mode 1
DMX CH
Mode 2
DMX CH
Mode 3
DMX CH
Mode 4
DMX
Value Funcon
10 26 48
Macro Run
0-15 No funcon
16-31 Macro Run 1
32-47 Macro Run 2
48-63 Macro Run 3
64-79 Macro Run 4
80-95 Macro Run 5
96-111 Macro Run 6
112-127 Macro Run 7
128-143 Macro Run 8
144-159 Macro Sound 1
160-175 Macro Sound 2
176-191 Macro Sound 3
192-207 Macro Sound 4
208-223 Macro Sound 5
224-239 Macro Sound 6
240-255 Macro Sound 7
11 27 49 Macro Speed
0-255 Macro Speed from Slow To Fast
12 28 50
Dynamic Rotate
0-15 No funcon
16-31 Dynamic Rotate 1
32-47 Dynamic Rotate 2
48-63 Dynamic Rotate 3
64-79 Dynamic Rotate 4
80-95 Dynamic Rotate 5
96-111 Dynamic Rotate 6
112-127 Dynamic Rotate 7
128-143 Dynamic Rotate 8
144-159 Dynamic Rotate 9
160-175 Dynamic Rotate 10
176-191 Dynamic Rotate 11
192-207 Dynamic Rotate 12
208-223 Dynamic Rotate 13
224-239 Dynamic Rotate 14
240-255 Dynamic Rotate 15
13 29 55 Dynamic Rotate Speed
0-255 from Slow To Fast
This manual suits for next models
1
Table of contents
Languages:
Other Flash Lighting Equipment manuals
Flash
Flash F7100566 User manual
Flash
Flash F7000547 User manual
Flash
Flash FL-330 BEAM 15R User manual
Flash
Flash F7100323 User manual
Flash
Flash F7000050 User manual
Flash
Flash LIGHT BOX MOON 2 User manual
Flash
Flash F7100250 User manual
Flash
Flash F7100070 User manual
Flash
Flash LOGO User manual
Flash
Flash LED PAR 18x10W RGBW 4in1 IP20 User manual
Flash
Flash FOLLOW SPOT 350W User manual
Flash
Flash 7X40W BIG EYE PRO User manual
Flash
Flash HYBRID 10R User manual
Flash
Flash F7100752 User manual
Flash
Flash F7000563 User manual
Flash
Flash P7100546 User manual
Flash
Flash 19x40W PRO User manual
Flash
Flash FTB-324-2 User manual
Flash
Flash F7100102 User manual
Flash
Flash F7100330 User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
