Fishman BP-100 User manual

USER GUIDE

BP-100

2

Welcome

Thank you for making Fishman a part of your acoustic experience. We are proud

to offer you the ﬁnest acoustic ampliﬁcation products available: high-quality

professional-grade tools which empower you to sound your very best.

3

Troubleshooting

If you are unfamiliar with this product, please pay close attention to the

requirements for installation. Failure to do so can result in permanent damage

to the pickup.

Installation by a qualiﬁed professional is strongly recommended.

Technical support, troubleshooting tips and installation information can be

found at http://www.ﬁshman.com/support/

4

Installation

Prepare the bridge

1. The area of the bridge where the elements

will be mounted must be ﬂattened with a

sanding block or a ﬂat ﬁle. Otherwise, the

performance of the pickup will be adversely

affected. Most problems with the pickup’s

performance can be remedied by ﬂattening

the bridge face.

Use a 120–150 grit sanding block or a ﬁle to

ﬂatten the area that will make direct contact

with the elements. Check the ﬂatness of the

bridge face with the edge of a steel ruler or

single-edged razor blade.

2. Clean the bridge with alcohol before

mounting the elements. Remove all rosin

deposits.

ISOLATION PLUG

IN WING HOLE

SENSING

ELEMENT

FELT-COVERED

SPRING CLIP

5

Mount the pickup

Caution: do not pull or bend the wires at the bases of

the elements. You may destroy the pickup!

1. Slide the pickup wire through the E-string side

wing slot.

2. Center the elements black side up on the side of

the bridge that faces the ﬁngerboard, as shown, with

the straight edge 1⁄8” below the top edge bevel of the

bridge top. The felt-covered clip should be pushed

tightly against the top of the bridge. A loose clip may

be tightened by squeezing it before installation.

3. Weave the ground wire over the string ball-ends

making sure to contact each ball.

4. Determine which isolation plug ﬁts snugly into the

E-string side wing-hole on the bridge. Slip the wire

into the slit of the isolation plug and ﬁt the plug into

the wing-hole.

GROUND

WIRE

OUTPUT

WIRE

6

Fine Tuning

• Mounting the elements ¼” to ½” below the top edge of the bridge

will produce a different sound.

• You may ﬁne tune the string balance by moving the upper corner of an

element closer to or further from an individual string.

• Once the optimum position is determined, the elements should not be

disturbed or removed from the instrument.

• The mounting clips must be tight. They should be retightened after

installation to compensate for compression of the felt.

7

Plugging In

An impedance matching preamp is recommended, but not required. This will

help realize the full frequency response potential of the pickup and allow for

cable runs longer than 10 feet without signal deterioration. Use a high quality,

low capacitance ¼” shielded instrument cable. This will ensure minimal tone

coloration and hum.

WWW.FISHMAN.COM

009-015-001 Rev C 4-09

Table of contents

Other Fishman Amplifier manuals

Fishman

Fishman PREFIX PREMIUM User manual

Fishman

Fishman PREFIX PRO User manual

Fishman

Fishman Stereo Amplifier User manual

Fishman

Fishman PREFIX PLUS User manual

Fishman

Fishman LOUDBOX ARTIST User manual

Fishman

Fishman Loudbox Performer User manual

Fishman

Fishman PRESYS PLUS User manual

Fishman

Fishman PRESYS ONBOARD PREAMP User manual

Fishman

Fishman LOUDBOX PERFORMER - ANNEXE 324 User manual

Fishman

Fishman PRO-EQ User manual

Fishman

Fishman PRESYS I User manual

Fishman

Fishman Loudbox Mini User manual

Fishman

Fishman PREFIX - ANNEXE 600 User manual

Fishman

Fishman PRESYS PLUS User manual

Fishman

Fishman AGP-2 User manual

Fishman

Fishman AG-125 - User manual

Fishman

Fishman LOUDBOX ARTIST User manual

Fishman

Fishman Aura User manual

Fishman

Fishman Loudbox User manual

Fishman

Fishman ELLIPSE AURA RETAIL User manual

Fishman

Fishman PLATINUM PRO EQ User manual

Fishman

Fishman POWERMIX User manual

Fishman

Fishman F1 AURA+ User manual

Fishman

Fishman POCKER BLENDER User manual

Popular Amplifier manuals by other brands

ASTRO

ASTRO HVO V40 P operating manual

Marantz

Marantz SUPERSCOPE BLA-545 Service data

NAD

NAD CI980 Quick setup guide

Technics

Technics SE-CH770 Service manual

Harman Kardon

Harman Kardon HK6300 instruction manual

NAD

NAD T975 owner's manual

McIntosh

McIntosh MA6850 Brochure & specs

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N manual

Viatron

Viatron Autrix Technical manual

GME

GME GA9800 instruction manual

Atlas

Atlas CP700 Specification sheet

Roland

Roland KC-1000 owner's manual

Pyle

Pyle PFMRA350BW user manual

Advantage

Advantage S-250 manual

IRT Electronics

IRT Electronics DVA-3007 manual

Dimavery

Dimavery BA-100 Series user manual

Sony

Sony XM-S400D operating instructions

Schertler

Schertler ROY X quick guide