Fishman POWERCHIP Safety guide
Powerchip
PPiieezzoo//MMaaggnneettiiccOOnnbbooaarrddMMiixxiinnggPPrreeaammpp
PPiieezzoo//MMaaggnneettiiccOOnnbbooaarrddMMiixxiinnggPPrreeaammpp
OWNER’S MANUAL • INSTALLATION GUIDE
TM
PPiieezzoo//MMaaggnneettiicc
PPiieezzoo//MMaaggnneettiicc
OOnnbbooaarrddMMiixxiinnggPPrreeaammpp
OOnnbbooaarrddMMiixxiinnggPPrreeaammpp
Thank you for purchasing this Fishman Powerbridge accessory. We are con-
fident that the Powerchip will significantly enhance the performance of your
Powerbridge system. If you have any questions or comments, please con-
tact our Customer Service Line at 978-988-9665.
Warning
Installation of the Powerchip may require structural modification to the gui-
tar. We strongly recommend that any modifications be performed by a com-
petent repair person. Fishman Transducers will be in no way responsible for
damages to the guitar, incurred as a result of improper installation.
Description and Features
The Powerchip is a miniature onboard Piezo/Magnetic pickup mixing pre-
amp, dedicated to the Fishman Powerbridge system. The preamp, mounted
to the underside of a volume pot, allows guitarists to combine or split Piezo
and Magnetic pickups without any additional outboard signal routing elec-
tronics.
The Powerchip features an independent Piezo volume control, and internal
“set it and forget it” Phase and Piezo Trim controls. A “smart” electronic
switch in the Powerchip circuit automatically routes Piezo and Magnetic
pickup signals to either stereo or mono signal paths.
Powerchip
2
Piezo/Magnetic Outboard Mixing Preamp
3
Mono Operation
Plug a standard mono instrument cable into the output of the Powerchip
equipped guitar and combine the Magnetic and Piezo signals into a single
buffered composite, suitable for any available instrument level audio input.
Powerchip
4
Stereo Operation
Plug a stereo “Y” cable into the output of the Powerchip equipped guitar and
split the Magnetic and Piezo pickup signals to separate destinations. Send
the buffered Piezo signal (Ring) to any instrument level audio input, such as
an acoustic instrument amplifier or PA system. Send the unbuffered,
“immaculate” Magnetic pickup signal (Tip) to a traditional electric guitar
amplifier, with no added coloration or signal treatment between the Magnetic
pickup and the amplifier.
5
Piezo/Magnetic Outboard Mixing Preamp
Piezo Trim and Phase
Adjust the small rotary trim pot on the backside of the Powerchip to match
Piezo and Magnetic pickup levels.
Move the Phase jumper on the backside of the Powerchip to eliminate phase
cancellation between the Piezo and Magnetic pickups.
Prepare the Instrument
TELECASTERTM
STYLE GUITARS
File or sand down the corners of
the 9-Pin Jack to fit the standard
TelecasterTM mounting hole.
STRATOCASTERTM STYLE GUITARS
You will need to drill out the back wall of the jack cavity to accommodate the
supplied 9-Pin Jack. Remove the output jack from the jack plate, then
replace the jack plate on the guitar. Use a pencil through the jackplate to
mark the center where your drill will enter the back of the jack cavity. Use a
3/4” (19mm) spade bit to drill out the back of the jack cavity.
Powerchip
6
Piezo/Magnetic Outboard Mixing Preamp
7
Installation and Connections
WARNING:
The solder pad terminals and the adjacent components on the
Powerchip circuit board are quite fragile and can be easily overheated. Use
only a low wattage soldering iron (30 watts max) to make your wire connec-
tions. To best utilize the space inside the guitar, solder the wires to the cir-
cuit board so that they exit toward the volume pot terminals.
1. Strip 3/32” (2.4 mm) and tin the wire ends of the pickups
2. Solder the Piezo pickup wire to the circuit board
The pads are located on the side of the board opposite the volume pot. The
Piezo hot wire goes to the pad on the right edge of the board, directly under
and to the right of the little white trimmer pot. Solder the Piezo ground wire
(which should be left with the braid intact), to the pad labeled “G” on the
right edge of the board, directly under the Piezo hot wire.
Powerchip
8
Installation Continued
3. Solder the Magnetic pickup hot wire to the circuit board
The pad for the hot wire is located on the same side of the board as the vol-
ume pot. This pad, labeled “M”, is on the left edge of the board, 3/4”
(19mm) from the bottom of the board. A common system ground is located
on the opposite side of the board, on a second pad marked “G”, adjacent to
the Piezo ground. Since there is room for only one wire on this pad, we sug-
gest that you tie all grounds to the body of the Magnetic volume pot, and
run a jumper wire to the ground pad on the circuit board.
NOTE:
If you install The Powerchip with active magnetic pickups (such as
EMG), the Powerchip and the active pickups will share the same battery.
Connect the positive battery wire from the magnetics to the +9V pad on the
Powerchip. Connect the negative battery wire from the magnetics to termi-
nal #1 on the nine pin jack.
4. Solder the 9-Pin jack to the system
A prewired output cable from the Powerchip is to be soldered to the provided
9-Pin Jack. Prepare the jack by soldering a jumper wire between the sleeve
terminal,located on the business end of the jack, and terminal #2, directly
below.
Solder the jack as follows:
a. Solder the shield from the output cable to terminal #2.
b. Solder the red wire from the output cable to terminal #4.
c. Solder the white wire from the output cable the terminal #8.
d. Solder the black battery wire (negative) to terminal #1.
Piezo/Magnetic Outboard Mixing Preamp
9
Powerchip
10
Optional Accessories
•
Piezo-Magnetic Pickup Selector Switch
-
A three position switch for
selecting between Piezo and Magnetic pickup combinations.
•
Battery Compartment - A flush mounted, pivoting compartment allows
easy access and quick battery changes.
Other manuals for POWERCHIP
1
Table of contents
Other Fishman Amplifier manuals
Fishman
Fishman ELLIPSE AURA - User manual
Fishman
Fishman PREFIX SERIES PREAMP - CUTOUT User manual
Fishman
Fishman PRO-EQ PLATINUM BASS User manual
Fishman
Fishman LOUDBOX PRO User manual
Fishman
Fishman Loudbox Performer User manual
Fishman
Fishman PREFIX PLUS-T - SCHEMA User manual
Fishman
Fishman AURA PRO RETAIL User manual
Fishman
Fishman Loudbox Mini User manual
Fishman
Fishman Loudbox 100 Setup guide
Fishman
Fishman ELLIPSE AURA RETAIL User manual
Fishman
Fishman LOUDBOX ARTIST User manual
Fishman
Fishman AGP-2 User manual
Fishman
Fishman PRESYS ONBOARD PREAMP User manual
Fishman
Fishman Loudbox Performer Owner's manual
Fishman
Fishman Prefix Pro blend User manual
Fishman
Fishman Prefix Pro blend User manual
Fishman
Fishman LOUDBOX MICRO User manual
Fishman
Fishman PREFIX STEREO BLENDER User manual
Fishman
Fishman PRO-EQ User manual
Fishman
Fishman Prefix Pro User manual
