Firstech BLADE Series User manual

CM-900

CM-900S/900AS

CM7X00

CM7000/7200 Cut loop for A/T

CM900AS/900S Jumper

DEREK ZOOLANDER

Est. 2001

CENTER KIDS

WHO CAN’T READ GOOD

for

Green White/BluePark / Auto

I/O Changes

HoodIGN

Lights

CANInstallYearModelMake

BLADE FEATURE COVERAGE

PARKING LIGHTS

SECURE TAKEOVER

GLOW PLUG STATUS

TACH OUTPUT

E-BRAKE STATUS

BRAKE STATUS

RAP SHUTDOWN

DOOR STATUS

DISARM OEM ALARM

ARM OEM ALARM

DOOR UNLOCK

DOOR LOCK

PRIORITY UNLOCK

IMMOBILIZER DATA

Ignition connection.

Ignition jumper, NO CONNECTION required.

Vehicle hood status ( - ).

Not required.

Required CAN connections.

Firmware: Covered vehicles use either BLADE-AL(DL)-CH8, confirm application, flash module, and update the controller

firmware before installing.

Install: Type 2 vehicles use the included CAN extension cable to source CAN data from the green CAN junction block

(left side of the dash) or from the BCM (pin#25, CANH, brown, pin #26, CANL, yellow).

Lighting: Type B parking lights use the 10-pin connector, secure unused 6-pin connector for safety.

Ignition: Common ignition provisions are listed in the BLADE diagram, ignition is also available at the vehicle BCM

(connector C5/E, pin #27, pink/white).

Hood: Hood status wire is available at the vehicle BCM, connector C1, pin #11 (violet/blue).

FTI-CDP1 - Installation and Configuration Notes

FTI-CDP1 - Vehicle Coverage and Preparation Notes

CONNECT TO PINK.

3500 TIP Start Diesel 2018 Type 2 CJB Type B BCM BCM

DL-CH8

RAM

Firstech

Techfeedtree

Diesel WTS

Set feature

option 4-10-4

pink

pink/black

PWR

BLADE

12 11

C1 - Hood pin ( - )

26 25

C5 - Ignition

violet/blue

HOOD

BCM

TIP Start Cylinder

OBD-II connector

Headlight switch

AUTO

pink

green

Green

Junction Block

*Not required

Type B

pink/white

brown

yellow

Driver side dash

H L

RAP SHUTDOWN

FTI-CDP1 - DL-CH8 - Type 2

LED Programming Error Codes

Module LED flashing RED during programming

1x - CAN Error, check CAN wiring and voltages

2x - Key code not learned, confirm unlock sent, check CAN

3x - No immobilizer data, check immo data connection

4x - No IGN, check IGN connection

5x - VIN not found, check CAN connections

6x - No immobilizer data, check immo data connection

7x - Not the same key, use only one key for programming

8x - No immobilizer data, check immo data connection

9x - No immobilizer data 10x - Klon error, redo Klon

2018 RAM 3500 TIP Start Diesel

Patent No. US 8,856,780 CA 2759622

INSTALL GUIDE

ALL IN ONE

DODGE/RAM

MODULE PROGRAMMING PROCEDURE - WITH KLON

9Turn key to ON position.

4Turn key to ON position.

15 Turn key to ON position.

11 Turn key to OFF position.

OFF

6Turn key to OFF position.

OFF

17 Turn key to OFF position.

OFF

19 Turn key to OFF position.

OFF

20 Module Programming

Procedure completed.

1Close driver door.

Re-open driver door to wake up

data bus.

2Press UNLOCKon OEM remote.

If the vehicle is not equipped

with an OEM remote, press the

module programming button.

7Remove key.

8Insert key into ignition.

3Wait, LED will ﬂash BLUE once

[1x].

5Wait, LED will turn solid RED.

10 Wait, LED will ﬂash BLUE.

16 Wait, LED will turn solid BLUE

for 2 seconds.

14 WARNING: Do not press RS

programming button.

Connect power ﬁrst.

Connect RS to vehicle.

13 Connect RS to computer

and proceed with extended

programming.

12 WARNING:

Disconnect power last.

Disconnect RS from vehicle.

18 Turn key to START position.

START

COM-BLADE-AL(DL)-CH8-EN 20191004

Doc. No.: ##65995##

Patent No. US 8,856,780 CA 2759622

INSTALL GUIDE

ALL IN ONE

DODGE/RAM

NOTICE

WARNING: READ BEFORE REMOTE STARTING THE VEHICLE

IMPORTANT

I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.

TAKE OVER PROCEDURE - TO THE VEHICLE OWNER

!Failure to follow procedure within time restriction will

result in vehicle engine shutdown.

3Take over procedure completed.

2TIME RESTRICTI N

Within 45 SECONDSfrom

previous step:

Open vehicle door.

Enter vehicle.

Close vehicle door.

Insert key into ignition.

Turn key to ON position.

Press and release BRAKE pedal.

NOTE

I All vehicle doors must be closed and locked prior to remote

start sequence.

1Press UNLOCK on after-market

remote.

TIME RESTRICTI N COMING UP !

COM-BLADE-AL(DL)-CH8-EN 20191004

Doc. No.: ##65995##

This manual suits for next models

Other Firstech Automobile Accessories manuals

Firstech

Firstech 2WT13R-SF User manual

Firstech

Firstech FTI-FDK1 1A3 User manual

Firstech

Firstech Compustar FMX RF-2WG15R-FM User manual

Firstech

Firstech DASII-2021 Operating instructions

Firstech

Firstech RF-AR1WG14R-FM Technical manual

Firstech

Firstech 1WS2R-AF Technical manual

Firstech

Firstech FTI-FDK1- Type 2A1 Operating instructions

Firstech

Firstech 2WQ9R-FM User manual

Firstech

Firstech ADS FT-DC3-LC User manual

Firstech

Firstech FLEX 2 User manual

Firstech

Firstech FTI-GMT3 User manual

Firstech

Firstech FTI-HDP6 Operating instructions

Firstech

Firstech BLADE Series User manual

Firstech

Firstech FTI-HDP7 User manual

Firstech

Firstech FTI-NSP2 Operating instructions

Firstech

Firstech FTI-FDK1 User manual

Popular Automobile Accessories manuals by other brands

James Baroud

James Baroud Odyssey user guide

Motorola

Motorola i50sx owner's manual

Yakima

Yakima 9MM STANDARD BIKE MOUNT instructions

Feniex

Feniex T3 instruction manual

Renault

Renault 77 11 423 180 Installation instruction

Kia

Kia E8300-4D000 manual

Brink

Brink 756843 installation instructions

Whispbar

Whispbar K085W Fitting instructions

v.link

v.link CI-VL2-PC-HSD manual

Viking

Viking Stack-Rack Assembly and use instructions

Aries

Aries 203015 installation manual

Choetech

Choetech AT0005 user manual

ZZ2

ZZ2 ZZAIR-PRO instruction manual

Holman

Holman 4A80L installation guide

Thule

Thule 2075 parts manual

Motorola

Motorola T325 quick start guide

TAUBENREUTHER

TAUBENREUTHER 16-3950 FITTING INSTRUCTION

DV8

DV8 FBJL-02 Product installation manual