Fein ABS 18 User manual
Sahre / MVK 05 / 07
Alle Rechte bei FEIN, insbesondere für den Fall der Schutzrechtsanmeldung.
Jede Verfügungsbefugnis wie Kopieren und Weitergaberecht liegt bei FEIN.
FRT: ABS 18 und ASB 18
Contents
1. Technical data
2. Maintenance
3. Electrical check
4. Disassembly
5. Assembly
6. Tools
7. Charger, Batteries
8. Modifications, Extras, Infos for repair
Spare part lists and drawings please see Internet under
www.fein.com / Fein Service / Spare part catalogue
Sahre / MVK 05 / 07
Alle Rechte bei FEIN, insbesondere für den Fall der Schutzrechtsanmeldung.
Jede Verfügungsbefugnis wie Kopieren und Weitergaberecht liegt bei FEIN.
FRT: ABS 18 und ASB 18
1. Technical Data
Typ
Voltage
No load speed: 1.Gear
2.Gear
Max. torque level:
Soft case
Hard case
Percussion rate:
Drill-Ø Steel
Drill-Ø Wood
Drill-Ø Stone
Chuck capacity
Wood screws-Ø
Steel screws-Ø
Weight with Battery
Thread on chuck reception
Handy Master-Set with
suitable batteries:
Order number NiCd
Order number NiMH
ABS 18
18 V =
0-400/rpm
0-1400/rpm
35 Nm
60 Nm
13 mm
50 mm
--
2-13 mm
10 mm
M10
2,9 kg
1/2"/20 UNF-3B
7 113 06 50
7 113 06 51
ASB 18
18 V =
0-400/rpm
0-1400/rpm
35 Nm
60 Nm
6400 / 22400/bpm
13 mm
50 mm
16 mm
2-13
10mm
M10
3,0 kg
1/2"/20 UNF-3B
7 104 04 50
7 104 04 51
Sahre / MVK 05 / 07
Alle Rechte bei FEIN, insbesondere für den Fall der Schutzrechtsanmeldung.
Jede Verfügungsbefugnis wie Kopieren und Weitergaberecht liegt bei FEIN.
FRT: ABS 18 und ASB 18
2. Maintenance
Please make sure that electric tools are repaired,
serviced and tested by specialists. As repairs carried
out in an inexpert way may cause considerable
hazards for the user (BGV A2).
Please observe the legal environmental guidelines
for the disposal of batteries!
Use original FEIN spare parts only !
Sahre / MVK 05 / 07
Alle Rechte bei FEIN, insbesondere für den Fall der Schutzrechtsanmeldung.
Jede Verfügungsbefugnis wie Kopieren und Weitergaberecht liegt bei FEIN.
FRT: ABS 18 und ASB 18
2. Maintenance
Maintenance work is limited to careful handling of the machine,
to ensure free cooling slots, and to clean the housing, if and
when necessary. Ensure perfect charging condition of the
batteries.
The Handy Master is produced in modular construction which
means that defective units can be replaced as complete parts.
The exception is the replacement of the drill chuck. For this
purpose the gear has to be disassembled and a special tool is
required to unscrew the drill chuck.
Sahre / MVK 05 / 07
Alle Rechte bei FEIN, insbesondere für den Fall der Schutzrechtsanmeldung.
Jede Verfügungsbefugnis wie Kopieren und Weitergaberecht liegt bei FEIN.
FRT: ABS 18 und ASB 18
3.2. Trouble shooting
Failure Relief
1. Machine does not start Check charge condition of battery, if
necessary recharge battery.
Clean the contacts on the machine and battery.
Check electronic actuator.
2. No speed of the actuator Replace the entire electronic actuator (60).
(acceleration).
3. Drive shaft continues to turn when the Replace the electronic actuator (60).
actuator is released (no brake).
4. Machine runs, drive shaft can be held Permit speed 1 or 2 to snap in and/or
(no torque) replace the drive motor (50) and/or gear (40).
5. Strong gear noise, sized. Replace the entire gear (40).
6. When using the coupling for screw Replace the retaining ring (30).
action, the adjustment ring turns.
7. Drill chuck does not run round. 0.4 mm beat is permissible measured at a
distance of 25 mm in front of drill chuck end. In
case of excess, replace the striking train (40).
8. Striking impact too weak despite strong Replace entire gear (40).
contact pressure.
9. Defective spindle lock. Change entire gear (40).
Drill chuck cannot be opened and closed
with one hand.
Sahre / MVK 05 / 07
Alle Rechte bei FEIN, insbesondere für den Fall der Schutzrechtsanmeldung.
Jede Verfügungsbefugnis wie Kopieren und Weitergaberecht liegt bei FEIN.
FRT: ABS 18 und ASB 18
3.3. Check: Motor
1. Connect the motors (50)without gear to the corresponding source of
voltage to measure the current without load.
Maximum values:
9.6 V = 3.0 A
12 V = 6.0 A
14.4 V = 5.0 A
18 V = 3,8 A
Caution: The short-time make current peaks are higher than 10A !
2. When the upper value is exceeded, the motor has to be cleaned, the
plain bearings have to be lubricated with special oil (10 ml bottle,
order ref.: 3 21 32 023 02 6), if this does not help, replace the motor.
Sahre / MVK 05 / 07
Alle Rechte bei FEIN, insbesondere für den Fall der Schutzrechtsanmeldung.
Jede Verfügungsbefugnis wie Kopieren und Weitergaberecht liegt bei FEIN.
FRT: ABS 18 und ASB 18
3.4. Check: Switch
Switch test:
- Disconnect the motor (50) from the gear unit (40).
- Disconnect the motor (50) from the switch (60).
-Connect approx. 15 cm of cable to the switch (60) on the motor side
and pass it out again on the drill chuck side.
- Connect cable passed out to a lamp bulb (e.g. 12V car lamp).
- Place upper part of housing.
- Push on the battery.
- Check functions.
Observe: Middle position of the change-over switch blocks the switch
pusher.
This manual suits for next models
1
Table of contents
Other Fein Drill manuals
Fein
Fein DDSK 672 User manual
Fein
Fein ASCM 18 QM Select 3850 User manual
Fein
Fein Slugger HoleMaker III User manual
Fein
Fein MBS16X User manual
Fein
Fein KBE30 User manual
Fein
Fein BOP 6 Setup guide
Fein
Fein DSk 658 User manual
Fein
Fein 7 205 43 User manual
Fein
Fein HandyMaster ASB 14V User manual
Fein
Fein Slugger JHM Magforce X User manual
Fein
Fein KBM 32Q User manual
Fein
Fein KBH25-2U Series User manual
Fein
Fein ABS 14 Setup guide
Fein
Fein KBU 35 PQ Setup guide
Fein
Fein BOZ 32-4M Setup guide
Fein
Fein DS 648 Quick start guide
Fein
Fein Slugger JMU 137 QW Series User manual
Fein
Fein HandyMaster ABS 12V Quick start guide
Fein
Fein HandyMaster ABS 14V Quick start guide
Fein
Fein ASye 636 Kin Quick start guide
