Fantech RIL-125 User manual

RIL-150

RIL-200

INSTALLATION & MAINTENANCE

INSTRUCTIONS

,Q/LQH

'XFW0RXQWHG)DQ

RIL-100

RIL-125

Specification

snoisnemiD

Model A B C D E F G Weight kg

RIL-150 112 60 100 80 295 147 200 2.7

RIL-200 124 94 108.5100 302 198 217 4.9

Electrical Data

Model Speed

r/min FLC Amps Input W

RIL-100 High 2200 0.11 24

RIL-100 Low 1850 0.10 18

RIL-125 High 2250 0.13 30

RIL-125 Low 1900 0.10 22

General

1.1. It is important that these Installation and Maintenance Instructions

are fully adhered to.

1.2.All electrical installations must be carried out by a suitably qualified

and competent personnel in accordance with all statutory

requirements.

1.3. The fan is designed for use in an ambient temperature of up to 40°C.

It is not suitable for corrosive or explosive atmospheres.

1.4. The installer should provide easy access to the fan to facilitate future

maintenance, and ensure that the fan is adequately supported.

Page 2 of 4

RIL-100 100 60 88 80 303 97 176 2

RIL-125 100 60 88 80 258 123 176 2

1.5 This product is not intended for use by persons (including children)

with reduced physical sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the product by a person responsible

for their safety. Children should be supervised to ensure that they do

not play with the product.

1.6 Precautions must be taken to avoid back-flow of gases into the room

from the open flue of gas or other fuel burning appliances.

1.7 A minimum of one (1) metre of duct is to be fitted to the fan inlet and

discharge spigots.

1.8 To avoid a hazard, a damaged supply cord must be replaced by the

manufacturer.

Installation

Warning: The fan must be isolated from the power supply during

installation and maintenance.

2.1.Upon receipt, the fan should be inspected for any damage.

2.2.Check the details on the rating plate to ensure that the correct power

supply is available

2.3. Means for electrical disconnection must be incorporated in the wiring

installation in accordance with the relevant wiring regulations.

2.4.Remove the fan body from the spigots that are attached to the base,

by releasing the two retaining clamps RIL-100 / RIL-125.

Page 3 of 4

Specification

snoisnemiD

Model A B C D E F G Weight kg

RIL-150 112 60 100 80 295 147 200 2.7

RIL-200 124 94 108.5100 302 198 217 4.9

Electrical Data

Model Speed

r/min FLC Amps Input W

RIL-100 High 2200 0.11 24

RIL-100 Low 1850 0.10 18

RIL-125 High 2250 0.13 30

RIL-125 Low 1900 0.10 22

General

1.1. It is important that these Installation and Maintenance Instructions

are fully adhered to.

1.2.All electrical installations must be carried out by a suitably qualified

and competent personnel in accordance with all statutory

requirements.

1.3. The fan is designed for use in an ambient temperature of up to 40°C.

It is not suitable for corrosive or explosive atmospheres.

1.4. The installer should provide easy access to the fan to facilitate future

maintenance, and ensure that the fan is adequately supported.

Page 2 of 4

RIL-100 100 60 88 80 303 97 176 2

RIL-125 100 60 88 80 258 123 176 2

1.5 This product is not intended for use by persons (including children)

with reduced physical sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the product by a person responsible

for their safety. Children should be supervised to ensure that they do

not play with the product.

1.6 Precautions must be taken to avoid back-flow of gases into the room

from the open flue of gas or other fuel burning appliances.

1.7 A minimum of one (1) metre of duct is to be fitted to the fan inlet and

discharge spigots.

1.8 To avoid a hazard, a damaged supply cord must be replaced by the

manufacturer.

Installation

Warning: The fan must be isolated from the power supply during

installation and maintenance.

2.1.Upon receipt, the fan should be inspected for any damage.

2.2.Check the details on the rating plate to ensure that the correct power

supply is available

2.3. Means for electrical disconnection must be incorporated in the wiring

installation in accordance with the relevant wiring regulations.

2.4.Remove the fan body from the spigots that are attached to the base,

by releasing the two retaining clamps RIL-100 / RIL-125.

Page 3 of 4

Installation (cont)...

2.5. Mount the base in the desired position using the fasteners supplied.

2.6. Replace the fan body in-between the spigots and tighten the two

retaining clamps or clamp screws.

Fan Maintenance

3.1. Inspect the fan at least once every 12 months to ensure that the motor

and fan blades are clean. Any build up of dust should be removed using

a non-abrasive cleaner.

3.2. All fastenings should be checked for tightness.

3.3. Bearings are of the ‘sealed for life’ type and will not need a detailed

inspection.

Wiring Diagram

Part No: INST-RIL-SW 11/12

RIL-150SW

RIL-200SW

INSTALLATION & MAINTENANCE

INSTRUCTIONS

In-Line

Duct Mounted Fan

Specification

Dimensions

Model A B C D E F G H J

Weight

RIL-150SW 112 60 100 80 295 147 200 225 236 2.7

RIL-200SW 124 94 108.5 100 302 198 217 235 265 4.9

Speed Speed r/min

Electrical

Data

Model FLC Amps Input W

RIL-150SW HIGH ( II ) 2500 0.22 50

LOW ( I ) 1950 0.19 44

RIL-200SW HIGH ( II ) 2500 0.50 120

LOW ( I ) 2000 0.45 100

To select high or low speed, switch the speed selector fitted to

the side of the unit’s junction box to either “II” for high speed or

“I” for low speed.

General

1.1. It is important that these Installation and Maintenance Instructions are

fully adhered to.

1.2. All electrical installations must be carried out by a suitably qualified

and competent personnel in accordance with all statutory requirements.

1.3. The fan is designed for use in an ambient temperature of up to 40°C.

It is not suitable for corrosive or explosive atmospheres.

1.4. The installer should provide easy access to the fan to facilitate future

maintenance, and ensure that the fan is adequately supported.

1.5 This product is not intended for use by persons (including children)

with reduced physical sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the product by a person responsible

for their safety. Children should be supervised to ensure that they do

not play with the product.

1.6 Precautions must be taken to avoid back-flow of gases into the room

from the open flue of gas or other fuel burning appliances.

1.7 A minimum of one (1) metre of duct is to be fitted to the fan inlet and

discharge spigots.

1.8 To avoid a hazard, a damaged supply cord must be replaced by the

manufacturer.

Installation

Warning: The fan must be isolated from the power supply during

installation and maintenance.

2.1. Upon receipt, the fan should be inspected for any damage.

2.2. Check the details on the rating plate to ensure that the correct power

supply is available

2.3. Means for electrical disconnection must be incorporated in the wiring

installation in accordance with the relevant wiring regulations.

2.4. Remove the fan body from the spigots that are attached to the base by

releasing the two retaining clamps (RIL-150SW, see diagram), or the

two clamp screws (RIL-200SW).

Installation (cont)...

2.5. Mount the base in the desired position using the fasteners supplied.

2.6. Replace the fan body in-between the spigots and tighten the two

retaining clamps.

Fan Maintenance

3.1. Inspect the fan at least once every 12 months to ensure that the motor

and fan blades are clean. Any build up of dust should be removed

using a non-abrasive cleaner.

3.2. All fastenings should be checked for tightness.

3.3. Bearings are of the ‘sealed for life’ type and will not need a detailed

inspection.

Wiring Diagram

Please note that the ProVent with run-on timer (models RIL-150T and RIL-200T is single speed only,

is not suitable for speed control and does not come with a plug and lead.

Part No: INST-RIL-T 11/12

RIL-150T

RIL-200T

INSTALLATION & MAINTENANCE

INSTRUCTIONS

In-Line

Duct Mounted Fan

Specification

Dimensions

Model A B C D E F G H J

Weight

RIL-150T 112 60 100 80 295 147 200 225 236 2.7

RIL-200T 124 94 108.5 100 302 198 217 235 265 4.9

Electrical Data

Model

Speed

r/min FLC Amps Input W

RIL-150T 2500 0.22 50

RIL-200T 2500 0.50 120

General

1.1. It is important that these Installation and Maintenance Instructions

are fully adhered to.

1.2. All electrical installations must be carried out by suitably qualified

and competent personnel in accordance with all statutory

requirements.

1.3. The fan is designed for use in an ambient temperature of up to 40°C.

It is not suitable for corrosive or explosive atmospheres.

1.4. The installer should provide easy access to the fan to facilitate future

maintenance, and ensure that the fan is adequately supported.

1.5 This product is not intended for use by persons (including children)

with reduced physical sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the product by a person responsible

for their safety. Children should be supervised to ensure that they do

not play with the product.

1.6 Precautions must be taken to avoid back-flow of gases into the room

from the open flue of gas or other fuel burning appliances.

1.7 A minimum of one (1) metre of duct is to be fitted to the fan inlet and

discharge spigots.

1.8 Fan Run-on is from 1 to 30 minutes. Adjust via the trim-pot fitted in

the junction box.

Installation

Warning: The fan must be isolated from the power supply during

installation and maintenance.

2.1. Upon receipt, the fan should be inspected for any damage.

2.2. Check the details on the rating plate to ensure that the correct power

supply is available

2.3. Means for electrical disconnection must be incorporated in the wiring

installation in accordance with the relevant wiring regulations.

2.4. Remove the fan body from the spigots that are attached to the base by

releasing the two retaining clamps (RIL-150T, see diagram), or the

two clamp screws (RIL-200T).

Page 2 of 4 Page 3 of 4

This manual suits for next models

Table of contents

Other Fantech Fan manuals

Fantech

Fantech RVF 4XL User manual

Fantech

Fantech 2SHE Series Parts list manual

Fantech

Fantech DBF110 User manual

Fantech

Fantech Ezifit Thru Roof ERV150 User manual

Fantech

Fantech SHR 6904 User manual

Fantech

Fantech SHR 1504 User manual

Fantech

Fantech PB Series User manual

Fantech

Fantech VER150 User manual

Fantech

Fantech FTC-P-18-5 User manual

Fantech

Fantech FKD 8XL User manual

Fantech

Fantech OdourVac Service manual

Fantech

Fantech 6M EC User manual

Fantech

Fantech SHR series User manual

Fantech

Fantech SER200 User manual

Fantech

Fantech VHR 2004 User manual

Fantech

Fantech 2VLD12 Series User manual

Fantech

Fantech VER100 User manual

Fantech

Fantech Jetstream JCE150SJK User manual

Fantech

Fantech MINITUBE Series Installation and operating instructions

Fantech

Fantech HV-150CAP User manual

Fantech

Fantech SHR 1504 User manual

Fantech

Fantech ERV-WI 500 User manual

Fantech

Fantech PB110L7 Manual

Fantech

Fantech FR Series User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual