Fantasea CP 8 User manual

Manual for Fantasea CP 8 Camera Housing for

Nikon Coolpix 5700 and 8700

www.fantasea.com - [email protected]

Table of Contents

INTRODUCTION ---------------------------------------------------------------------------------3

GENERAL SPECIFICATIONS ----------------------------------------------------------------4

FEATURES AND ACCESSORIES INCLUDED WITH THE HOUSING-------------4

FUNCTIONS [CONTROL DETAILS]--------------------------------------------------------5

SET UP INSTRUCTIONS -----------------------------------------------------------------------6

EXCLUSIVE PRESSURE RELEASE PLUG----------------------------------------------------------6

OPENING LEVERS----------------------------------------------------------------------------------7

MAINTENANCE OF THE O-RING SEAL-----------------------------------------------------------8

MOUNTING THE CAMERA IN THE HOUSING----------------------------------------------------9

USE & CARE OF HOUSING ----------------------------------------------------------------- 11

PRE DIVE FUNCTION CHECK ------------------------------------------------------------------- 11

GENERAL OPERATION -------------------------------------------------------------------------- 11

CLEANING & STORAGE--------------------------------------------------------------------- 11

CARE AND MAINTENANCE --------------------------------------------------------------------- 11

TRAVELING -------------------------------------------------------------------------------------- 12

ACCIDENTS--------------------------------------------------------------------------------------- 12

WARRANTY ------------------------------------------------------------------------------------- 12

INTRODUCTION

Welcome to the exciting world of underwater digital SLR photography. Your purchase of the

Fantasea CP 8 housing for Nikons 8700 digital camera will set you apart from other

photographers. With this system, you will enjoy the best chance of capturing the widest

variety of superior underwater images. The CP 8 offers you the opportunity to use the exact

Nikon lenses for the best circumstances, including a choice of macro, wide angle, fisheye and

zoom lenses. You will find the housing to be easy and intuitive to use and operate and you will

have countless dives in which to experiment with the CP 8's advanced imaging capabilities.

Fantasea Line Photo is please to offer our help with any of your photographic needs.

The purpose of this manual is to provide you with the basic introduction to your CP 8, which

should get you comfortable with the housing and allow you to get started taking great

underwater images right away. We strongly urge you to thoroughly read the Nikon 8700

instruction manual as well to familiarize yourself with the most common controls and settings

that you will use for your underwater photography. The CP 8 housing will permit access to

most of the important controls on the camera. To take full advantage of these features, it is

recommended to have a good command of what each option can do for you, so you will know

when you should use each specific control.

GENERAL SPECIFICATIONS

•Test Pressure Fantasea Housings are individually tested to 300 feet

•Closure Design Air Lock

•Body Material Polycarbonate

•Overall Size 210 x 210 x 170 mm (LxWxH)

•Total Weight Approximately 2.0 Kg (Housing only)

•Buoyancy

(with camera) Approximately neutral in salt water

FEATURES AND ACCESSORIES INCLUDED WITH THE

HOUSING

•Additional Features Visible main O-ring for final pre-dive check

•Double O-ring design on all controls

•Bulkhead and hotshoe plug for strobe

•Accessories Standard Port (included)

•Spare main O-ring (included)

•Universal tool (included)

•Silicone O-ring grease (included)

•Carry bag (included)

•Red filter (optional)

•Extension arm for strobe or video light (optional)

•Video light VL035(optional)

•Macro, Wide Angle Lens (optional)

•Macro, Wide and Dome Ports (optional)

•Housings for DTTL Speedlight SB800 (optional)

FUNCTIONS [CONTROL DETAILS]

1. ON/OFF, Shutter

2. Mode:

•Exposure

Compens

ation,

•Backlight,

FUNC

3. Command Dial

4. Flash, Image Quality:

•AE/AF

Lock,

Focus

Mode

5. Zoom

6. Quick Review / Play

7. Selector Confirm

8. Monitor

9. Quick View

10. Multi Selector

11. Delete, DISP

SET UP INSTRUCTIONS

Exclusive Pressure Release Plug

The body and lid are uniquely designed with a "no clip" closure arrangement. Our testing has

shown that this arrangement allows the water to exert an even pressure on the O-ring, thus

increasing the reliability of the watertight seal. To open the housing, the pressure release plug must

be first unscrewed and then pulled all the way out. This provides a channel for the air to pass

though and eliminate the pressure differential between the inside of the housing and the ambient air

pressure.

The plug consists of an internal double O-ring seal on a stainless steel slide shaft. These internal O-

rings form the watertight seal. There is also a large outer O-ring under the knob. This O-ring serves

to prevent contamination [dirt or salt] of the slide shaft, and is not required for watertight integrity.

If this O-ring should become detached, it can simply be pushed back in place.

Important! Before diving, make sure the pressure release

plug is pushed closed, and then screwed home, do

not over tighten this plug (finger tighten only).

Opening Levers

After unscrewing and pulling out the pressure release plug, the lid can be opened. To overcome the

friction of opening, two levers are used to push against the lid with a cam action. On some models

these opening levers are bolted to the body. On the other models, they are detachable levers.

Important! Be sure they are inserted all the way flat to the

housing before turning to avoid damaging the

protrusions on the lid.

The body has two holes on opposite corner edges of the housing for opening. Gently lever off the

lid with the supplied cams taking care not to twist the lid excessively. The lid should be opened

keeping it approximately parallel to the body at all times. If using a single lever, turn first one side a

little, then the other an equal amount, and repeat again until the lid is opened. Remember to

unscrew and pull out the pressure release plug all the way first, otherwise the air pressure will resist

attempts at opening. Lay the lid on a flat stable surface after opening.

Cam Levers Cam Lever in Housing

Maintenance of the O-Ring Seal

The O-ring seal is the only barrier between the water outside and the air space within the camera. It

is an effective barrier only if the seal is properly maintained. The O-ring seal should be inspected

before every dive. The following information is provided for your guidance in using and

maintaining the O-ring seal.

Maintaining the O-Ring Seal:

If the main body to lid O-ring is not installed, install the O-ring before diving. This is the only user

serviceable O-ring. Its care and maintenance is critical to the watertight integrity of the housing.

The O-ring should be replaced at the proper service interval (see Section on Service). If the O-ring

is contaminated, or not already installed, inspect, grease and install the O-ring according to the

following guidelines.

Guidelines For Inspection, Cleaning And Re-Instillation Of The O-Ring

[Gasket]:

Materials Needed:

You will require a soft cotton cloth or q-tip. Make sure these are free of all chemicals or

contamination such as loose fibers. You will also require the tube of silicone grease supplied with

the housing. Note that other types of silicone grease specifically for use with underwater camera

equipment can usually also be used. It is advised to carry out the following procedure on a firm

clean level surface, e.g. at a table), to prevent skidding. This is especially useful if you are doing

this maintenance from your diving boat as it moves with the wave swells.

When To Maintain the O-Ring Seal:

Remove the O-ring periodically for inspection. It is not necessary to remove, clean and re-install the

O-ring after every dive provided the O-ring did not become contaminated. The housing may be

required to be opened between dives, to replace memory card or recharge the batteries. Before

opening, make sure the outside of the housing is thoroughly toweled dry. After removing the lid and

servicing the camera, replace the lid straight away rather than leaving it lying around. Before

replacing the lid, make sure that no contamination such as dust, hair, salt, etc. has fallen onto the O-

ring or O-ring recess, as a precaution we recommend maintaining the O-ring every time the lid is

opened.

Procedure for O-Ring Maintenance:

1. Place the lid on a firm non-slip level surface.

2. The O-ring can be extracted using an O-ring extractor tool (make sure

the tool has no sharp edges). Alternatively use the flat surface of your

thumbs to gently stretch the O-ring on two faces thus making a small

loop protruding a few mm. The loop can then be grasped between finger

and thumb, to pull the O-ring over the lip.

3. Clean the O-ring recess (the square groove where the O-ring sits) with a

cotton bud.

4. Inspect the O-ring all the way round its surface for damage such as cuts

tears or contamination. This should be done visually and also by feeling

the surface texture between finger and thumb.

5. IF THE O-RING IS DAMAGED OR SUSPECTED OF BEING

DAMAGED, DISCARD IT IMMEDIATELY. A spare O-ring is supplied

with your housing, or a replacement O-ring can be obtained from

Fantasea. If the O-ring is contaminated or suspected of being

contaminated, clean it with a cotton cloth that is free of all chemicals or

contamination. After cleaning inspect the O-ring again.

6. Once the O-ring has been inspected and verified fit for use, apply a

SMALL amount of silicone grease to the O-ring. The silicone grease

must be evenly distributed around the O-ring

7. Replace the O-ring into the groove; run a finger round the O-ring to

make sure it is snugly seated in the groove.

Mounting The Camera In The Housing

Remove the lens cap and wrist strap:

Make sure the camera lens to body orientation is set so the LCD screen is at top view with lens at

the extended position. The pressure release plug is pulled out before inserting the camera.

Attach the plastic slide plate:

Attach the plastic slide plate to the camera’s tripod mounting fixture with a coin, screw driver or the

end of the universal tool supplied. Take care not to excessively tighten the screw. Slide the camera

into the body along the guide rail inside the bezel. Make sure the camera body is inserted to the

limit and test the function of the ON/OFF button on the body of the housing.

Note! If you find that the control levers do not articulate

properly with the camera buttons, please check

again that the camera is properly seated to the

limit of the guide rail.

Replace the lid:

Remember to pull the pressure release plug all the way out while closing the lid, otherwise the air

cannot escape. Squeeze the lid closed all the way, you will hear the hiss of air being expelled.

Screw home the pressure release plug:

There is no need to excessively tighten this plug. The internal O-ring makes the seal. The O-ring on

the underside of the plug is just to keep the shaft dirt free.

After replacing the lid, make a final visual inspection of the main O-ring for contamination.

Note!

If the O-ring is in good contact, a thin black line,

about 0.5-1mm in width should be visible where

the O-ring is in contact with the lid. Follow this

line all the way round the edge of the seal as a

final check that the seal is good.

The housing is now ready for the dive.

Table of contents

Other Fantasea Camera Accessories manuals

Fantasea

Fantasea BlueRay Illuma User manual

Fantasea

Fantasea Flex Arm User manual

Fantasea

Fantasea EyeGrabber F Series User manual

Fantasea

Fantasea FP7100 Installation guide

Fantasea

Fantasea FS 1 User manual

Fantasea

Fantasea FS-6 User manual

Fantasea

Fantasea CP 8N User manual

Fantasea

Fantasea FSD-1100 User manual

Fantasea

Fantasea Cool flash nano User manual

Fantasea

Fantasea FG16 User manual

Fantasea

Fantasea CP-5 User manual

Fantasea

Fantasea FP-4 User manual

Fantasea

Fantasea F400D User manual

Fantasea

Fantasea FS-210 User manual

Fantasea

Fantasea FE 330 User manual

Fantasea

Fantasea Line FP7000 Housing Installation guide

Fantasea

Fantasea FS200 User manual

Fantasea

Fantasea FP-1 User manual

Fantasea

Fantasea FL?22 User manual

Fantasea

Fantasea LED 360 Light User manual

Fantasea

Fantasea Remora Flash User manual

Fantasea

Fantasea BigEye Lens S95 User manual

Fantasea

Fantasea Nano Flash User manual

Fantasea

Fantasea EyeDaptorGSeries?F67 User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions

Custom Brackets

Custom Brackets Digital PRO-M Instructions for use