Falcon DOMINATOR PLUS E3405 CHIP SCUTTLE User guide

DOMINATOR PLUS E3405 CHIP SCUTTLE

INSTALLATION and

SERVICING INSTRUCTIONS

Caution: Read the instructions before

using this appliance.

IMPORTANT

The installer must ensure that the installation of the appliance is in conformity with these instructions and National

Regulations in force at the time of installation. Particular attention MUST be paid to –

BS7671 IEE Wiring Regulations

Electricity at Work Regulations

Health And Safety At Work Act

Fire Precautions Act

This appliance has been UKCA/CE marked based on compliance with the relevant Electrical and Electromagnetic

Compatibility (EMC) Regulations/Directives for the voltages stated on the data plate.

WARNING -THIS APPLIANCE MUST BE EARTHED

On completion of the installation these instructions should be left with the Engineer-in-Charge for reference during

servicing. Further to this, The Users Instructions should be handed over to the User, having had a demonstration of

the operation and cleaning of the appliance.

IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE INSTALLING AND COMMISSIONING

THIS APPLIANCE. FAILURE TO COMPLY WITH THE SPECIFIED PROCEDURES MAY RESULT IN DAMAGE OR THE NEED

FOR A SERVICE CALL.

PREVENTATIVE MAINTENANCE CONTRACT

To obtain maximum performance from this unit regular servicing of the appliance should be undertaken to ensure

correct operation, it is functioning as intended, and safe to use. We recommend servicing in accordance with SFG20

Maintenance Schedules and as a minimum, after 2,500 hours of use, or annually, whichever comes first and that a

maintenance contract be arranged with an appointed service contact. Visits may then be made at agreed intervals

to carry out adjustments and repairs.

WEEE Directive Registration No. WEE/DC0059TT/PRO At end of unit life, dispose of appliance and

any replacement parts in a safe manner, via a licenced waste handler.

units are designed to be dismantled easily and recycling of all material is encouraged whenever

practicable.

Falcon Foodservice Equipment

Wallace View, Hillfoots Road,

Stirling, FK9 5PY, Scotland

01786 455200

T100824 Ref.8

IMPORTANTINFORMATION

ELECTRICAL SAFETY AND ADVICE REGARDING SUPPLEMENTARY ELECTRICAL

PROTECTION

Commercial kitchens and foodservice areas are environments where electrical appliances may be located

close to liquids, or operate in and around damp conditions or where restricted movement for installation

and service is evident.

The installation and periodic inspection of the appliance should only be undertaken by a qualified, skilled

and competent electrician; and connected to the correct power supply suitable for the load as stipulated

by the appliance data label.

The electrical installation and connections should meet the necessary requirements to the local electrical

wiring regulations and any electrical safety guidelines.

We recommend:-

•Supplementary electrical protection with the use of a type A residual current device (RCD)

•Fixed wiring appliances incorporate a locally situated switch disconnector to connect to, which is easily

accessible for switching off and safe isolation purposes. The switch disconnector must meet the

specification requirements of IEC 60947.

Your attention is drawn to:-

BS 7671:2018–Guidance Note 8 - 8.13 : Other locations of increased risk

It is recognized that there may be locations of increased risk of electric shock other than those specifically

addressed in Part 7 of BS 7671. Examples of such locations could include laundries where there are washing

and drying machines in close proximity and water is present, and commercial kitchens with stainless steel

units, where once again, water is present.

Where because of the perception of additional risks being likely, the installation designer decides that an

installation or location warrants further protective measures, the options available include:

•Automatic Disconnection of Supply (ADS) by means of a residual current device having a residual

operating current not exceeding 30mA;

•Supplementary protective equipotential bonding; and

•Reduction of maximum fault clearance time.

The provision of RCDs and supplementary bonding must be specified by the host organization’s appointed

installation designer or electrical contractor and installed by a suitably qualified and competent electrician so

as to comply with Regulations 419.2 and 544.2

SECTION 1 - INSTALLATION

UNLESS OTHERWISE STATED, PARTS WHICH HAVE BEEN PROTECTED BY THE

MANUFACTURER ARE NOT TO BEADJUSTED BY THE INSTALLER.

MODEL NUMBERS, NETT WEIGHTS

andDIMENSIONS

Model

Width

(mm)

Depth

(mm)

Height

(mm)

Weight

(kg)

E3405

400

770

825

SITING

The appliance should be installed on a level, fireproof surface, in a well lit and draught free position.

If the floor is constructed of combustible material, then local fire requirements should be checked to ensure

compliance. A clear space of 150mm should be left

below and also between rear and side of unit and any

non-combustible wall.

If this is not possible these surfaces should be clad in a suitable non-combustible, heat-insulating material. Close

attention be paid to Fire Regulations.

ELECTRICAL SUPPLY

The unit is suitable for AC supplies only.

The standard terminal arrangement is single phase

(230V~).

Live - Brown

Neutral - Blue

Earth - Yellow/Green

WARNING - THIS APPLIANCE MUST BE EARTHED

SUPPLY CONNECTION

A suitable mains input cable is supplied that conforms to

code designation 60245 IEC 57, cable type H07RN-F.

If cable is damaged, it must be replaced by a suitably qualified person.

Asuitably rated isolating switch with contact separation of

at least 3mm in all poles must be installed and wiring

executed in accordance with relevant regulations.

All external wiring must be executed in accordance with relevant regulations.

Access to mains terminal block is gained by removing control panel.

Check that no damage has occurred to the appliance, power cable and plug face during transit. If damage has

occurred do not use the appliance.

Ensure that the mains power cable is routed free from the appliance to avoid damage.

We recommend supplementary electrical protection with the use of a residual current device (RCD).

Periodical testing, repair and fixing wiring connection should only be undertaken by a skilled and competent

electrician.

This appliance is also provided with a terminal for connection of an external equipotential conductor. This

terminal is in effective electrical contact with all fixed exposed metal parts of the appliance, and shall allow

the connection ofa conductor having a normal cross-sectional area of up to 10mm². it is located on the rear

panel and is identified by the following symbol and must only be used for bonding purposes.

ELECTRICAL RATINGS

Electrical loading is as stated in table below and also on appliance data plate.

The location of mains isolating switch should be identified for use in any event of an emergency or during

cleaning.

Connection

A @ 230V

4.0

SECTION 2 - ASSEMBLY and COMMISSIONING

Note

The following information should be read as applicable to

the unit being assembled.

ASSEMBLY

a) Unpack and level appliance b) Remove all packaging

CONNECTION TO AN ELECTRICAL SUPPLY

Connect as detailed in Sections 1.3 and 1.4.

STARTING UP

Switch on mains supply. Red neon will light.

Press switch, amber neon will light

Ensure both elements heat up.

INSTRUCTION TO USER

After installation and commissioning is completed, please hand User Instructions to user and ensure that the

person(s) responsible understands the instructions regarding correct operation and cleaning of the appliance.

SECTION 3 - SERVICING and MAINTENANCE

SERVICE INFORMATION

This unit carries an extensive mainland UK warranty. The warranty is in addition to and does not change your

statutory or legal rights.

The warranty policy can be found on our website which details the conditions of the warranty and the

exclusions.

https://www.falconfoodservice.com/info-centre/policy

Service calls to equipment under warranty will be carried out in accordance with the conditions of sale.

Warranty calls can be made between 8:30 am and 5:00 pm weekdays only.

To ensure your warranty enquiry is handled as efficiently as possible, ensure you have the following

appliance information prior to calling us:

1. Model number –found on data plate

2. Serial number –found on data plate

3. Brief description of the issue

To contact Falcon for a warranty issue dial (UK only) 01786 455 200 and select Warranty Issues from the

menu.

ELECTRICAL MAINTENANCE WARNING

BEFORE ATTEMPTING ANY MAINTENANCE, ISOLATE APPLIANCE AT MAIN SWITCH AND

TAKE

STEPSTO ENSURETHATITIS NOTINADVERTENTLY

SWITCHED ON.

MAINTENANCE CHECK

Regular servicing of the appliance should be undertaken to ensure correct operation, it is

functioning as intended, and safe to use. We recommend servicing after 2,500 hours of use,

or annually, whichever comes first.

Any maintenance schedule should be carried out in accordance with SFG20 Maintenance

Schedules. Should any issues with the integrity of the components be identified these should be

replaced. If the appliance is not considered safe the unit should be removed from service and the

responsible person advised why the unit is not safe to use and what remedial action is needed.

Contents of the maintenance schedule should be agreed with the maintenance provider.

3.1 CONTROL PANEL REMOVAL

Remove 2 panel fixings from below hob. Release 3 fixings from below control panel.

Pull panel forward slightly from below and allow it to slide down until clear.

This will allow access to mains terminal block, neons and on/off switch

Toaccess gantry element, remove 10 fixings from around gantry. Disconnect element wires then remove securing clip.

Replace in reverse order.

To access lower element, remove control panel and one side panel. Disconnect element cables.

Remove support bracket nuts, lower element tray and remove element. Replace in reverse order.

Supply Cord Replacement

If supply cord is damaged, it must be replaced by the manufacturer, service agent or a suitably qualified person.

Note: If any current is out-with these tolerances, the cause must be investigated and rectified.

Phase Min (A)

Max (A)

Actual (A)

3.87

4.51

4.3

SECTION 4 - SPARES and

ACCESSORIES

When ordering spare parts, please quote model number,

serial number and voltage stated on data plate.

Red neon

Amber neon

On/off switch

Element ceramic

Element tubular

CIRCUIT DIAGRAM

L L

ON / OFF

Switch

Amber Neon

N N

E E

To Control

Panel Tag

WIRING DIAGRAM

Table of contents

Other Falcon Cooker manuals

Falcon

Falcon Mercury 1082 Induction Instruction Manual

Falcon

Falcon 1092 Deluxe Dual Fuel User guide

Falcon

Falcon Mercury 1082 Induction Instruction Manual

Falcon

Falcon Elan 110 Dual Fuel User manual

Falcon

Falcon 1000 Deluxe Induction G5 Instruction Manual

Falcon

Falcon 900 DL Induction User guide

Falcon

Falcon 1092 Continental Induction G5 Instruction Manual

Falcon

Falcon KCH110DFBLCEU Operation manual

Falcon

Falcon 900 Deluxe Induction Instruction Manual

Falcon

Falcon Kitchener Instruction Manual

Falcon

Falcon G2962 User manual

Falcon

Falcon Professional+FX Instruction Manual

Falcon

Falcon Classic 110 Dual Fuel User manual

Falcon

Falcon Excel FSD 110 User manual

Falcon

Falcon Professional+ FX 90 Induction G5 Instruction Manual

Falcon

Falcon F900 SERIES Manual

Falcon

Falcon 90 Induction U109988 - 02 Manual

Falcon

Falcon Elan 90 Duel Fuel FSD Operation manual

Falcon

Falcon Classic 110 gas Instruction Manual

Falcon

Falcon Professional+ 100FX Dual Fuel Instruction Manual

Falcon

Falcon 1200 Mercury Induction Instruction Manual

Falcon

Falcon Esprit 110 Induction Instruction Manual

Falcon

Falcon Classic 60 Dual Fuel User manual

Falcon

Falcon Toledo TXT110DFSSEU Operation manual

Popular Cooker manuals by other brands

Modena

Modena FC 7645 SGM User manual book

Electrolux

Electrolux Insight EKG6049 user manual

Stanley

Stanley Donard 60 Installation and operating instructions

Bartscher

Bartscher 201TC manual

Parkinson Cowan

Parkinson Cowan 50 GR/BU installation instructions

Siemens

Siemens HK9P00020U instruction manual

Creda

Creda S150E Installation and user instructions

Creda

Creda HB48309 instructions

Bosch

Bosch HCE743220F instruction manual

Tricity Bendix

Tricity Bendix SE545P manual

NEFF

NEFF E1461A2/01 Instructions for use

Zanussi

Zanussi ZCM 700 X Instruction booklet

Smeg

Smeg SNL61MA9 user manual

RiverGrille

RiverGrille TF2002501-RG Assembly instruction

Vollrath

Vollrath 69504F Operator's manual

Tricity Bendix

Tricity Bendix CSIE500 Operating and installation instructions

AEG

AEG Competence 5731 V Instruction book

Euromaid

Euromaid ES60 Installation and operation manual