Ezviz RS2 User manual
8
Overview
Package Contents
Docking Station *1
Robot Vacuum Cleaner *1
(hereinafter referred as to “robot”) Mop cloth *2 Mop Assmbly (with mop cloth) *2
Side Brush *2 Cleaning Tool *1 Camera Sticker *1
Power Cord *1 Quick Start Guide *2 Regulatory Information *1
The power cord's appearance is subject to the actual one you have bought.
9
Basis
Dust Box
Wi-Fi Indicator
Intelligent LED Ring
Bumper
Power Button
Bumper
Robot Upper Cover
Microphone
*
Reset Button *
Name Description
Power Button • Press and hold for 4 seconds: power on/off.
• Press once: start/pause working.
• Double press: end the task and return to the docking station.
Reset Button • Press and hold for 4 seconds: enter the network conguration.
• Press and hold for 10 seconds: restore factory settings and restart.
10
Universal Wheel
Cliff Sensor*6
Material Sensor
Side Brush
Main Brush
Drive Wheel
Mop Assembly
D-TOF Lidar
Edge Sensor
Charging Contact
Speaker
Infrared Receiving
Terminal
Side Brush
Drive Wheel
Mop Assembly
RGB Camera
Obstacle Sensor
Charging Contact
Air Outlet
Water Inlet
56
1
3
2
4
11
Cleaning Tool
Place for Spare
Mop Cloth
Cabin Door
Mop Assembly Platform
Cleaning Sink
Water Sensor
Used Water Tank
Operation Panel
Clean Water Tank
Cleaning Solution Inlet
Start/Pause • Press once: start/pause task.
• Press and hold for 2 seconds: end the task.
Sink Clean • Press once: the robot exits the docking station and the docking station
sprays water in the cleaning sink and waits for cleaning.
• Press again: the sewage will be drained.
Mode Press once: switch cleaning mode (vacuum before mop, vacuum while mop,
vacuum only, mop only, mop cloth cleaning, mop cloth drying).
12
Exit/Recall Press once: the robot exits/returns to the docking station.
+Child lock unlocking/locking Press and hold them for 2 seconds at the same time: unlock/lock the
child lock. When the child lock function is enabled, pressing the key on the
operation panel is invalid (you need to enable the child lock function on the
EZVIZ App rst).
Quick Start Guide
Preparation
Try to avoid using in the environment with stairs (if must, please set up a guardrail), and try to remove the obstacles on the
ground before use.
Connect the Power Supply to the Docking Station
Select a proper location, place the docking station on a horizontal floor against the wall, connect the docking station and the
power socket with the power cord, and the docking station will start automatically (it is recommended to place the docking
station on a flat light colored tile floor instead of a carpet).
No obstacles 1.5m(4.92’) ahead
>0.5m (1.64’) >0.5m (1.64’)
In order to avoid external heat damage to the docking station, please do not place it next to radiators, heaters, replaces,
etc.
13
Add Clean Water
Remove the protective bags of the clean water tank and the used water tank, ll the clean water tank with clean water, and then
install them back.
• Do not ll hot water, otherwise the device may be damaged.
• If you need to use cleaning solution, please use the cleaning solution produced by our company. Other cleaning
solution may damage the device.
MAX
Remove Shields
Install Side Brushes and Mop Assembly
Install the side brushes and mop assembly at the bottom: align the side brushes with the point as shown in the gure and press
them down. Hearing a “click” indicates that they are installed in place; Align the mop assembly with the magnetic point.
14
Get the EZVIZ App
EZVIZ App
1. Connect your mobile phone to Wi-Fi (only 2.4 GHz WiFi is supported).
2. Download and install the EZVIZ App by searching for “EZVIZ” in the App Store or Google PlayTM.
3. Launch the App and register an EZVIZ user account.
• If you have already used the App, please make sure that it is the latest version. To nd out if an update is available, go
to the App store or Google PlayTM and search for “EZVIZ".
• The actual process may vary due to ongoing App updates. Follow the instructions provided in the App.
Add the Robot to EZVIZ App
1. Log in to your account through EZVIZ App, tap the device adding icon and then the QR code scanning interface will be
displayed.
2. Press and hold the power button of the robot for 4 seconds until it starts.
3. Open the upper cover of the robot, scan the QR code on the robot body, and complete the network conguration and addition
of the robot according to the interface prompts.
If Wi-Fi connection failed, or you want to connect the robot to another Wi-Fi, you need to press and hold the reset button for
4 seconds, and then the robot will be restarted and you can add the robot to EZIVZ App again.
3
Scan to add device
12
Place the Robot
Place the robot in front of the docking station, and then press on the operation panel. The robot will enter the docking station
and start charging.
15
First Cleaning
You have two ways to operate:
• Press to select the cleaning mode, and press to work.
• Log in to your account through EZVIZ App, select the cleaning mode on the home page of the device, and click .
After the rst use, the robot will draw and record the indoor map. (in order to improve the efciency of drawing maps, please use
the vacuum only or vacuum before mop mode for the rst use )
• It is recommended to fully charge before rst use.
• In order to facilitate the smooth return to charge after cleaning, it is recommended to start from the docking station. Do
not move the docking station during cleaning.
Use the Camera Sticker (optional)
A camera sticker is provided if you need to cover the camera.
1. Tear off the protective lm.
2. Clean and wipe up the glass of the camera with wet tissue. Stick and press the camera sticker to the glass of the camera
and make sure it sticks rmly.
3. The sticker can be washed and reused.
3
12
The visual obstacle avoidance function of this product requires the camera to be on as one of the prerequisites, and the
image processing involved is done locally on the product and is not uploaded to EZVIZ CloudPlay. You can mask the camera
to reject the function as needed. The product package comes with a camera sticker for masking, which is electrostatically
adsorbed.
16
Operations on the EZVIZ App
The App interface may be different due to version update, and the interface of the App you installed on your phone shall
prevail.
Map for Cleaning
Map editing (segmentation, merging, area building, room naming, No-go area, invisible wall, rotation), map zoning, carpet display,
real-time cleaning route display, and multi-map saving.
Cleaning Method
General cleaning, personalized cleaning, scheduled cleaning, designated room cleaning, and area cleaning.
Cleaning Settings
Suction setting, water volume setting, cleaning sequence setting, carpet pressurization mode, supplementary sweeping for
carpet, and drying mop cloth time setting.
Housekeeping Function
Make an appointment for patrol inspection, xed-point motion, take photos/videos for patrol inspection, and voice intercom.
Information Display
Pets-caring time, cleaning history, patrol history, equipment power, consumables and maintenance.
More Features
Firmware upgrade, volume adjustment, Do Not Disturb mode, night vision light compensation, etc.
Routine Maintenance
To maintain the best condition of the device, please maintain the device and replace parts with following frequencies:
Robot Part Maintenance Frequency Replacement Frequency
Mop Cloth / Every 2-3 months
Side Brush Once every 2 weeks Every 3-6 months
Main Brush Once per week Every 6-12 months
Sponge Filter/
High Efciency Filter Once per week Every 3-6 months
D-TOF Lidar
RGB Camera
Edge Sensor
Obstacle Sensor
Cliff Sensor
Infrared Receiving Terminal
Bumper
Charging Contact
Universal Wheel/Drive Wheel
Once per week /
Cleaning Sink Once every 2 weeks /
Clean Water Tank Once every 3 months /
Used Water Tank After each mopping /
Docking Station Once every 2 weeks /
• Before performing cleaning and maintenance tasks on the device, turn the robot OFF and unplug the docking station.
• A multi-function Cleaning Tool is provided for easy maintenance.Handle with care, this cleaning tool has sharp edges.
• EZVIZ manufactures various replacement parts and fittings. Please visit www.ezviz.com for more information on
replacement parts.
17
Replace Mop Cloth
1
Please note that the mop cloth
should never cover the center
part of the mop bracket.
2
3
Dump the Dust Box
1
2
Press and hold the white button
on the dust box, the dust box
cover will open automatically,
and the garbage will be poured
out.
Other manuals for RS2
1
Table of contents
Other Ezviz Vacuum Cleaner manuals
