Exhale Fans EF34 User manual

Owner's Guide & Installation Manual

MODEL EF34

FANS

To view the LIMITED WARRANTY for this product, visit www.exhalefans.com.

WARNING: Read this manual before using this product. Failure to follow the instructions

and safety precautions in this manual can result in damage to property, serious bodily

injury or death. Keep this manual in a safe location for future reference.

WARNING: This appliance is not to be used by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction.

WARNING: If unusual oscillating movement is observed, immediately stop using the

ceiling fan and contact the manufacturer, its service agent or suitably qualied parsons.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

a) Use this unit in the manner intended by the manufacturer. If you have questions, contact the

manufacturer.

b) Before Servicing or Cleaning unit, switch power o at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

Model: EF34

Parts List

Tools Required

Screw Driver

Level

(Magnetic if available)

Wire Strippers

A A

B B

C C

D D

SHEET 1 OF 1

DRAWN

CHECKED

MFG

APPROVED

nhiner 5/17/2013

DWG NO

TITLE

SIZE

SCALE

REV

Exhale Fan (Prebuilt)

Dust Cover &

LED Light

DC Motor

Flat Head Motor Screws (1/4-20)

Qty: 5

Ceiling Mount

Motor Mount Screws (#10-24)

Qty: 4

Wire Nuts

Qty: 3

Misc Ceiling

Mounting

Screws

Qty: 4

Lock (Vibration)

Washers

Qty: 4

Wireless Remote

FANS

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

FANS

Safety First!

∞To reduce the risk of electric shock, ensure electricity

has been turned o at the circuit breaker or fuse box

before beginning any installation procedures.

∞All wiring must be in accordance with local electrical

codes. Electrical installation should be performed by a

qualied licensed electrician.

∞WARNING: To reduce the risk of electrical shock

and re, do not use this fan with any speed

control device other than the included wireless

remote.

∞The outlet box and support structure must be securely

mounted and capable of supporting a minimum of 50

pounds. Use only certied outlet boxes marked FOR

FAN SUPPORT.

∞WARNING To reduce the risk of re, electrical

shock or personal injury, only mount fan to

outlet box marked ACCEPTABLE FOR FAN

SUPPORT.

∞To avoid personal injury or damage to the fan and other

items, be cautious when working around or cleaning

the fan.

∞Do not use water or detergents when cleaning the fan

or fan discs. A dry dust cloth or lightly dampened cloth

will be suitable for most cleaning.

∞After making electrical connections, spliced conductors

should be turned upward and pushed carefully into the

outlet box.

∞Electrical diagrams are for reference only.

∞WARNING: To reduce the risk of personal injury,

use only the two steel screws (and lock washers)

provided with the outlet box for mounting to

the outlet box. Most outlet boxes commonly

used for lighting xtures are not acceptable

for fan support and may need to be replaced,

consult a qualied electrician if in doubt.

∞WARNING: This appliance is not to be used

by persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction.

∞Children (even supervised) should not play with the

appliance.

∞The Exhale Fan should be installed above the

oor at a height in accordance with local codes.

∞The replacement of parts of the safety suspension

system device shall be performed by the manufacturer,

its service agent or suitably qualied persons.

∞The xing means for attachment to the ceiling such as

hooks or other devices shall be xed with a sucient

strength to withstand 4 times the weight of the ceiling

fan.

∞The mounting of the suspension system shall be

performed by the manufacturer, its service agent or

suitably qualied persons.

∞Users are advised to contact the fan supplier to

conduct regular examination of the fan suspension

system at least once in every two (2) years.

∞All attachments of the fan suspension/

mounting hardware system are provided and

designed to be vibration proof. The mounting

screws are supplied with Lock/Vibration

washers that prevent each attachment point

from loosening while the fan is in operation.

∞For installation in the Country of Singapore.

The fan and its installation in particular

the Suspension/Mounting System shall be

Inspected/Examined at least once every two (2)

years.

∞WARNING: To reduce the risk of personal

injury, install fan at least 2.3 m. (7 ft.) or more

above the oor.

PLEASE READ AND SAVE THIS INSTALLATION MANUAL completely before you begin to install the Exhale™ Fan.

You will be happy you did.

To view the LIMITED WARRANTY for this product, visit www.exhalefans.com.

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

Model: EF34

Installation

Step 1. Determine the location

The preferred location for the EF34 is in the center of the room, this position will provide the best performance of

the fan.

If you intend to place multiple fans in the same room you should divide the room into equal sections and place

the fans in the center of each section. In both instances of one or multiple fans, the above recommendations will

provide air movement coverage to all corners of the space.

∞WARNING: To reduce the risk of re, electrical shock or personal injury, only mount fan to outlet box

marked ACCEPTABLE FOR FAN SUPPORT.

Step 2. Remove contents from the package

The 2-part protective foam covers the entire fan and through the hand hole openings lift the top cover from the

box. Located in each corner of the protective foam you will nd all the parts located in form tting slots. Included

are the DC motor, mounting hardware, remote, and LED light. Carefully remove each individual part ensuring that

all the parts are cross-referenced with the “Parts List” located in the front of this document.

Do not remove the body of the Exhale™ Fan at this time; that will come later in the installation.

Step 3. Turn o all electrical power

Locate your electrical panel or fuse box and turn o the power to the room where you are installing the fan.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

a) Use this unit in the manner intended by the manufacturer. If

you have questions, contact the manufacturer.

b) Before Servicing or Cleaning unit, switch power o at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

FANS

Step 4. Ceiling Mount

a. Pass the electrical wires from the ceiling through the ceiling

mount center hole as shown in Figure 1.

b. Secure the ceiling mount to the junction box

using the

hardware supplied with the junction box

as shown in Figure 2.

c. Using a level, make sure the mount is

plumb and level to the oor, adjust if

necessary.

Figure 1.

Junction Box

(Fan Rated)

Step 5. Electrical Connections

a. Connect the fan supply

(Black) wire to the black

household supply wire as

shown in Figure 4.

b. Connect the neutral fan

supply (White) to the white

household supply as shown

in Figure 4.

Start by hanging the motor from the ceiling mount hook as

shown in Figure 3.

Installation to concrete ceilings requires optional

mounting hardware. (See Optional Accessories A)

Junction Box (Fan

Rated)

Ceiling Mount

Ceiling

Figure 2.

Figure 3.

Safety Cable

and Hook

WARNING: Not using the hardware included with the junction box could result in a weak connection of

the ceiling mount to the junction box and cause the fan to become unstable or fall.

Running the Exhale out of level

can cause it to become unstable

or wobble.

Note: Your motor may be supplied with wiring colored

Red and Black or Black and White. For the Red and Black

colored wire pair, the Red wire is Line and the Black wire

is Neutral. For the Black and White colored wire pair, the

Black wire is Line and the White wire is Neutral.

c. Connect the Ground fan

wire (Green) to the ground

household supply as shown in

Figure 4.

d. After connecting all the wiring,

spread them apart so that

the Green and White wires

are located on one side of the

electrical box and the Black on

the other.

e. Turn the wire nuts upward and

push the wires neatly into the

electrical box so they are out of

the way.

f. Secure the fan safety cable

hook through the slot on the

ceiling mount that is opposite

of the ceiling mount hook.

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

Model: EF34

Figure 4.

Step 6. Mounting the Motor

Pre-install 2 of the included #10-24 screws half-way into the

ceiling mount on either side.

Install the motor onto the ceiling mount by sliding the pre-

installed bottom mount over the ceiling mount as shown in

Figure 5.

Using a clockwise twisting motion, the motor will temporarily

lock into the ceiling mount while you install the remaining 2 #10-

24 screws and tighten all connections.

Be sure an align the two twist lock channels with

the 2 pre-installed screws added rst.

Figure 5.

WARNING: To reduce the risk of electrical shock, DO NOT

use a wall-mounted speed control with this fan. It WILL

permanently damage the electronic circuitry.

WARNING: Turn o all electrical power prior to making

any electrical connections. Failure to do so could result in

electrical shock, personal injury, or death.

Use the wire connecting nuts supplied with your fan.

Secure the connectors with electrical tape.

Make sure there are no loose strands or connections.

The external earth conductor wire should be longer than

both the Line and Netural wires.

If you are unsure how to disconnect the electric power, or feel that

you do not have enough electrical knowledge, please consult a

licensed electrician for assistance.

If the installation uses the supplied expansion anchors or the

installation is in the Country of Singapore refer to the page in

this manual on Concrete Mounting Hardware under Operational

Accessories.

Household Supply

Black

White

Black

White

Ground

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

FANS

Step 7. Hanging the Disc Array

a. Using only (2) of the included 1/4-20 at head

motor mount screws, install them (2) full

rotations as shown in Figure 7.

Note: These screws will be tightened

completely in a later step.

Figure 7.

Install (2) motor mount screws 2 full

turns into the motor. The locations for

the screws are marked with a small

white mark.

WARNING: Not installing the screws a

full (2) rotations could result in them

backing out and causing the disc array

to fall prior to installing the remaining

screws.

b. Install the disc array onto the motor by aligning

the (2) screws installed earlier to the 'Key Holes'

in the disc array as shown in Figure 9.

c. Rotate the entire disc array counter clockwise to

lock the screws into the disc array as shown in

Figure 9.

Figure 8.

Note: The disc array should be free

hanging from the (2) mounting screws.

d. Install the remaining (3) screws into the disc

array tightening all (5) using an alternating

pattern to ensure an even pressure is put

on all screws.

Figure 9.

WARNING: Not tightening the

motor mounting screws properly

could result in a weak connection

of disc array to the motor and

cause the fan to become unstable

or fall.

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

Model: EF34

Remote Operation

BUTTON FUNCTIONS

Upper Left SPEED DOWN

Upper Right SPEED UP

Center Left Clockwise (CW)

Counterclockwise (CCW) rotation

Center Right FAN ON/OFF

Lower Left LED DIMMER

Lower Right LED ON/OFF

FANS

Figure 9a.

Step 8. Install the Dust Cover (Optional LED Lighting system? Skip this step)

Install the dust cover by sliding it over the center of the disc array as shown in Figure 10. The cover is held on by

friction and should t snugly without using extensive force.

Figure 10.

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

FANS

Remote Operation (Cont.)

Each remote is pre-programed to motor when packaged at the factory. However, we have added

instructions below on how to program the remote in the event that it may become necessary.

a. Install the two AAA 1.5 Volt Batteries into the remote transmitter by rst removing the battery cover on the

back cover. Insert the batteries as indicated with the positive + end of the battery aligned with the + sign on

the battery holder.

Operating Functions of the Remote:

The Remote Transmitter has Six Operational Buttons and are depicted (See Figure 9a)

∞To turn the fan ON or OFF select the button labeled POWER.

∞To Increase or Decrease fan Speed select SPEED UP or SPEED DOWN button. The illuminated scale at the

top of the remote will indicate the speed selected, 1 through 6.

∞Please note that the lighted scale on top of the remote will indicate the speed that your fan is operating.

∞To change the direction of rotation, Toggle the CW/CCW button for Clockwise direction or Counterclockwise

direction. The lighted scale will scroll when the CW/CCW button is depressed, right to left for Clockwise,

and Left to right for Counter Clockwise. With your Exhale Fan rotational direction is of personal preference,

performance and temperature are not aected.

∞Turning on the LED light is made by pressing the LED LIGHT ON/OFF button.

∞The LED DIMMER button is used to provide a full-scale dimmer function for your LED. Press and Hold

the dimmer button to select the level of illumination that you desire. While holding this button the level

of illumination will increase to 100% and then decrease to 20%, just release the button at the level of

illumination that you desire.

Remote Programming (Syncing the Remote):

∞Turn the power OFF for at least 10 Seconds, if necessary, turn o the Circuit Breaker that routes power to

your fan.

∞Turn Power to the Fan ON

∞Within 60 seconds of turning the power on, press and hold the LED ON/OFF button for 5 seconds. Do not

touch any other button during this process, doing so will cause this process to fail.

∞Once the Synchronization is completed and detected you will hear an audible “BEEP” which indicates a

successful synchronization.

∞After completing the steps all fan functions will be available.

Please note that if a Power Failure occurs you may have select the CW / CCW direction button since it is not

remembered by the fan.

Protected by one or more of the following US patents: (10,352,325 B2 / D676,543S / D676,952S)

Model: EF34

Model: EF34/220-240/50

Voltage: 220-240V 50 Hz. 3 Wire

Power: 65W 0.5A [without LED]

78W 0.6A [with LED]

INSU. Class: F Duty: Continuous

Model: EF34/120/60

Voltage: 120V 60 Hz. 3 Wire

Power: 65W 1.0A [without LED]

78W 1.15A [with LED]

INSU. Class: F Duty: Continuous

The motor is running with 24VDC and it will

not run without the electronic part.

Tech Specs

Dimensions Voltage & Current Rating

Height: 7.5 in / 18.4 cm

Width: 34 in / 86.4 cm

Weight: 25 lbs / 11.4 Kg

Level 1: 33-35 dB

Level 2: 35-37 dB

Level 3: 36-38 dB

Level 4: 37-38 dB

Level 5: 38-41 dB

Level 6: 40-45 dB

(40 dB = Quiet Library)

Energy Usage

Sound dB

Level 1: 4 Watts, 120 RPM

Level 2: 6 Watts, 158 RPM

Level 3: 9 Watts, 198 RPM

Level 4: 16 Watts, 236 RPM

Level 5: 36 Watts, 274 RPM

Level 6: 50 Watts, 285 RPM

Cleaning and Maintenance

WARNING: Make sure the fan is turned o and is not spinning before attempting to clean with either of

the methods listed above.

With any fan, dust will collect on the leading edges where the air passes over.

Using a damp cloth with a mild detergent, wipe the dust from the interior and exterior edges of the discs.

Alternatively, you can use the brush attachment

of your vacuum cleaner to remove dust

collected on the interior and exterior surfaces

of the fan.

We recommend cleaning the fan once a month

to keep dust to a minimum and keep your fan

running at its optimum.

Optional LED Lighting System

Watts: 15 at 100%

Dimmable: 20% to 100%

Lumens: 850-1050 at 100%

Cool White: 5500K

Warm White: 4000K

Other manuals for EF34

Table of contents

Other Exhale Fans Fan manuals

Exhale Fans

Exhale Fans EF34 User manual

Exhale Fans

Exhale Fans EF34 Instruction manual

Exhale Fans

Exhale Fans EF34 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual