Ewheels EW-500 Manual

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Assembly and Setup Instructions

EW-500

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Please observe and follow these instructions closely as it will insure safe and reliable operation.

Tools you will need to assemble the EW-500

1. Phillips Screwdriver

2. 12mm Socket Driver or Socket Wrench w/ Extension

3. 17mm Wrench

4. 15mm Wrench

5. Pliers

6. Knife

1. Remove the EW-500 from it’s carton. Start by opening the top to allow access to the inside of the carton.

Use a knife to cut each corner from the inside out (Figure A). Once all four corners are cut it will allow 360

degree access to your new moped eliminating heavy lifting.

2. Place the EW-500 on it’s kickstand.

(A)

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Handlebar Installation

Tools you will need to attach the Handlebar

- 12mm Socket Driver or Socket Wrench w/ Extension

- 17mm Wrench

1. Slide Handlebar assembly onto Fork/Steer tube and align corresponding holes.

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Handlebar Installation

2. Connect the Handlebar assembly and Fork/Steer tube together with the bolt and radiused spacer provided

(Figure B). The notch shown in Figure B needs to be vertically aligned.

3. Once bolt is in, turn the bars to the left or right as far as they will go. This will allow you to nger tighten the

locknut on. Still in the turned position tighten bolt with your 12mm socket driver or socket wrench w/ extension

and 17mm wrench.

(B)

Notch

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Front Fender Installation

Tools you will need to attach the front fender

- Phillips Screwdriver

1. Screws come screwed into fender bracket on the forks. You need to unscrew the three screws shown in

(Figure C). Align all three holes on the fender with fender bracket on the forks and screw back in.

(C)

Headlight Installation

Tools you will need to attach the headlight

- Phillips Screwdriver

1. Connect Headlight to wiring harness shown in (Figure D).

(D)

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Headlight Installation

2. Use provide fairing tab to cover wiring harness hole. Snap into place and pull until it matches the radius of

the fairing.

3. Attach light using the provide screws. 1 in the front on the light bracket the other 2 on the light itself.

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Front Wheel Installation

Tools you will need to attach the front wheel

- 17mm Wrench

- Pliers

1. Unscrew the saddle nut at the end of the brake cable to loosen tension on the front brake.

(Figure E).

2. Slide front axle and spacer onto the right side (None brake side) of the fork (Figure F).

3. Move front wheel into place. Insert brake drum into wheel and line up all holes (Figure G). Then slide axle

through and tighten bolt with Pliers and 17mm wrench. (Note) Make sure to mate the tab on the fork with the

slot on the drum brake as the front wheel is attached (Figure H)

(E) (F)

(G) (H)

Saddle Nut

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Front Wheel Installation

4. Tighten the saddle nut at the end of the brake cable to create tension on the front brake (Figure I). Test front

brake as you tighten the saddle nut. Tighten until brake lever has about .75” between the lever and grip.

(I)

Rear Brake Installation

4. Unscrew saddle nut on the end of the brake cable (Figure J). Remove the barrel plug and slide it into the

drum brake arm. Then attached brake cable through the hole in the barrel plug (Figure K) and tighten saddle

nut (Figure L). Tighten the saddle nut at the end of the brake cable to create tension on the rear brake. Test

rear brake as you tighten the saddle nut. Tighten until brake lever has about .75” between the lever and grip.

(J) (K) (L)

Saddle Nut

Barrel Plug

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

Rear Rack Installation

Tools you will need to attach the rear rack

- Phillips Screwdriver

1. Remove rear pad with phillips screwdriver

2. Attach rack with four screws using a phillips screwdriver

3. Re-install rear pad. Be sure to use the integrated clip when re-installing (Figure M).

(M)

Storage Box Installation

Tools you will need to attach the storage box

- Phillips Screwdriver

- Pliers

1. Center open storage box on rear rack with storage lever facing toward the back.

2. Place one mounting plate and two screws through the inside holes (Figure N).

3. Use the remaining mounting plate underneath the storage box and nger tighten the nuts on (Figure O).

4. Tighten using phillips screwdriver and pliers.

(N) (O)

e wheelsewheelsTM

Electric Wheel LLC - electricwheelstore.com - 888-518-3588 (Toll Free) - One Riverway-Suite1700, Houston,TX 77056

License Plate Holder Installation

Tools you will need to attach the license plate holder

- Phillips Screwdriver

1. Remove provide screws with phillips screwdriver from license bracket (Figure P).

2. Align plate holder with the holes on licence bracket and re-install all screws and tighten (Figure Q).

(P) (Q)

Pedal Installation

Tools you will need to attach the pedals

- 15 mm Wrench

1. Hand tighten each pedal and tighten with 15 mm wrench.

Popular Scooter manuals by other brands

TEKTRO

TEKTRO CHEETAH owner's manual

Douglas

Douglas Vespa Sprint Operation and maintenance

PLAYTIVE

PLAYTIVE AS-2448 Instructions for use

Ebinger

Ebinger DONKEY XL User instructions

Flyer

Flyer Mountain Original instruction manual

BackCountry eBikes

BackCountry eBikes Storm owner's manual

equipmed

equipmed FreeRoam II user manual

Yoto

Yoto Lion owner's manual

WESTHILL BIKES

WESTHILL BIKES LINK user manual

BAnff

BAnff eProdigy series Assembly manual

Winther

Winther 475 Assembly instruction

Jetson

Jetson JBZL17 user manual

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 user manual

Carrera

Carrera impel manual

Afikim

Afikim Superlight SL-3 user manual

CareCo

CareCo ZOOM owner's manual

Douglas

Douglas Vespa G.S. Service manual

Gazelle

Gazelle with BOSCH System user manual

ewheels EW-500 Manual

Popular Scooter manuals by other brands