Everest EBC37 User manual
Thank you for choosing EVEREST
A Step Above the Standard
Owner’s Manual for models:
www.EVEREST .ref
com
Horizontal Bottle Coolers EBC37, EBC50, EBC65, EBC80, EBC95
ISO-9001
US
R
C
When installing the unit, be careful that the
electrical cord is not under the unit or
pressed against the wall.
This could cause a damage
to the cord.
time, make sure the unit
is free from all packaging.
Packaging left
on the unit
during
operation may
To prevent electrical shock, please do
not plug or unplug the cord
with wet hands.
WARNING - When using your appliance, always follow basic precautions, including
the following :
Install the unit on a hard
and level surface.
Before cleaning or maintaining the unit,
please unplug it. Do not use any
around the unit.
Please do not store temperature
sensitive items in the unit,
such as medical or
science research
related materials.
If you suspect a refrigerant leak,
unplug the unit and
immediately contact an
authorized service
technician.
Please do not hang or climb
on the unit as this may
cause the unit to fall.
Safety Notices
Safety Notices
REFRIGERATION
1
Safety Notices
Safety Notices
To prevent electrical shock and
malfunction, do not spray the
unit with water.
Clean the pronges of the electrical plug
with a soft cloth or brush before plugging
it into an electrical receptacle to prevent a
WARNING - Read and follow all safety notices in this installation guide.
information. Failure to do so may lead to serious injury and /
or damage to the unit.
When it is time to salvage the unit, make
sure to remove the the doors to prevent
the risk of children or animals getting
trapped inside the unit.
REFRIGERATION
2
To minimize shock and re hazards, be sure
not to overload the outlet into which the
unit is plugged into. A dedicated circuit of
sucient amperage is required.
To prevent damage to the electrical
components, have the unit plugged in directly
to its own circuit. EVEREST is not responsible
for any damage caused by improper electrical
connections resulting from electrical power
failure, use of extension cords &
surge protectors, and any
voltage drops to the unit.
Caution!
Caution!
To prevent electrical shock and damage to
the electrical cord, please hold
the plug head
when plugging
and unplugging
the unit.
Do not use the
electrical cord
or plug if they
are damaged
in any way.
REFRIGERATION
To avoid personal injuries
from broken glass,
please do not
place glass items
in the freezer.
After unplugging the unit, please wait at
least 6 minutes
before re-plugging
it in. Failure to do
so could cause
extensive damage
to the compressor.
If the unit will
not be used for an
extended period of
time, please unplug
it from the outlet.
The refrigerator compartment temperature
should be set at 32F°~42°F(See page 9).
Setting the
temperature
out of the
recommended
ranges will void the
unit’s warranty.
Do not put your hands under the unit when
moving it. You could be injured by sharp
edges, protruding parts,
crushing, etc.
Please do not attempt to
remove or
repair any
components
unless you are
an authorized
service technician.
Avoid installing the
unit where it could
be exposed to
water or
moisture.
3
Installation Guide
Installation Guide
Install the unit on a hard and level surface
or the unit could produce undesired noises.
The unit should be at least 2” away from the
wall.
Indoor Use Only
Outdoor use may cause a decrease in
unit.
Dusty and High Humidity Areas
Dusty environments will cause the
condenser coil to prematurely clog which
will require it to be cleaned more often.
High humidy environments could cause the
unit to rust.
Do not build an enclosure or cabinet
around the unit.
condenser area will cause the compressor to
work harder, which can result in compressor
failure and the unit not being able to
maintain the desired temperature.
Select a location away from other heat
and moisture generating equipment
such as stoves, ovens, dish washers, etc.
High ambient temperatures cause the
compressor to work harder, which can result
in compressor failure and the unit not being
able to maintain the desired temperature.
REFRIGERATION
4
Shlef Cleaning
Periodically remove the shelves from the unit and clean them
with mild soap and warm water.
Do not use the following products when cleaning
Clean the exterior of the product with mild soap and warm water.
Never use steel wool, strong acids, abrasive cleaners or degreasers.
Acidic products and products containing vinegar must
be stored in sealed containers to prevent acid damage
to the interior of the unit and the evaporator coil. (Rust
resulting from the lack of or improper maintenance will
not be covered under warranty.)
Interior Cleaning
Clean the interior surface of the unit with mild soap and warm
water. Do not let water accumulate inside the unit. To prevent
water damage, wipe the interior of the unit with a dry cloth as
needed. Do not use abrasive cleaners, concentrated detergents,
bleaches, cleaning waxes, solvents or polishes to clean the interior
of the unit.
Condenser Coil Cleaning
Poor condensing unit performance is caused by heavy dust
build-up on the condenser coil. The condenser coil should be
condenser with a soft brush or a vacuum with a brush
attachment. The condenser coil should be cleaned in the
Maintenance Guide
Maintenance Guide
REFRIGERATION
5
Condenser Coil Maintenance
Condenser Coil Maintenance
REFRIGERATION
6
Diagram EBC-L-001-D1
Diagram EBC-L-001-D2
Diagram EBC-L-001-D3
Model Shown: EBC50
EBC Series
Applicable Model Prefix: EBC/EGC
IMPORTANT: Failure to clean the condenser coil will result in a void of warranty.
Follow these simple steps at least once a month to ensure the proper operation of your Everest product.
1. Always unplug the unit before performing maintenance.
2. Locate the condenser coil at the front, right side of the unit. See diagrams EBC-L-001-D1 and EBB-L-001-D3.
3. Unscrew the front grill completely. See diagrams EBC-L-001-D1 and EBC-L-001-D2
4. Use any hard bristled brush in a vertical sweeping motion to remove lint, dust and debris from in between the aluminum
fins of the condenser coil. Do not apply heavy pressure so as not to bend the fins*.
5. For grease-coated fins, use any commercial condenser coil cleaner*. Please follow the specific instructions on the bottle.
6. Repeat steps 4 to 5 until fins are clear of any blockage from lint, dust or grease.
* Do not use vacuum brush attachments and abrasive, acid-based cleaners or degreasers to avoid damage to the aluminum fins.
REFRIGERATION
Please check the following before requesting service.
a. Ensure the electrical cord has been connected.
b. Ensure the unit is turned on.
a. Adjust the temperature control to a warmer
setting.
a. This is the sound of the refrigerant circulating
during the compressor rest period and it is
normal.
a. Heaters have been placed around the door
openings to prevent condensation buildup.
This is normal.
a. Condensation can occur during hot and
humid
weather with frequent or prolonged door
opening.
This is normal.
b. The doors might not be closed properly.
a. Condensation on the exterior surface of the
unit is perfectly normal during periods of high
humidity.
b. Check door alignment and gaskets for proper
seal.
a. Check for loose parts.
b. Check for tubing rattle.
c. Check for a bent fan blade.
d. Check for damaged fan motor bearings.
e. Ensure the unit is stable.
f. Ensure the cabinet is level.
a. Check the door gaskets for proper seal.
b. Check to see if the temp. control setting is too
high, then adjust as necessary.
c. Avoid installing the unit next to heat generating
equipment and direct sunlight.
d. Avoid storing hot contents.
e. Ensure the doors are fully closed.
7
Ratchet Lock & Shelves Installation
Ratchet Lock & Shelves Installation
REFRIGERATION
Ratchet lock Assembly
Insert the ratchet [A] into the
hole [B] of the door handle.
Push the ratchet [A] all
the way in until it is fully
attached to the surface
of the product.
[A]
[B]
[C]
Insert the lock [C] into the
ratchet [A] until the lock [C]
hits the door handle [E].
Then turn the key to lock it.
[A]
[E]
Step 1
Step 2 Step 3
[A]
Place the bottom shelves on
the cabinet oor. Fit the spring into the partition
shelf marked “A”.
Insert the partition shelf at a 45 degree angle
so that the spring ts into the hole located at
the back wall as shown in Picture 1.
Picture 1
Push the shelf towards the back wall and align
the other end of the shelf in place so that it
rmly stands vertically as shown in Picture 2.
Picture 2
Step 1 Step 2
Step 3
[Ratchet Lock Installation]
[Shelves Installation]
8
Specifications
Specifications
REFRIGERATION
Model
Capacity(Cu.Ft.)
Door
# of Bin Dividers
# of Floor Shelves
Compressor (HP)
Power (V-Hz-Ph)
Temp. Range(F)
Refrigerant
Crated Weight(LBS)
Amps(A)
13.60
2
3
2
1/4+
115 -60-1
32~ 42
245
4.20
9.30
1
2
1
1/4+
115-60-1
32 ~ 42
R-134A R-134A
R-134A R-134A
R-134A
204
4.20
18.90
2
4
2
1/4+
115-60-1
32 ~ 42
286
4.20
EBC37 EBC50 EBC65
Dimensions
(W x D* x H inches) 36 3/4 x 26 3/4 x 33 5/8
Specications subject to change without notice.
*Depth does not include bottle cap opener with integrated cap receptacle.
49 1/2 x 26 3/4 x 33 5/8 64 5/8 x 26 3/4 x 33 5/8
Model
Capacity(Cu.Ft.)
Door
# of Bin Dividers
# of Floor Shelves
Compressor (HP)
Power (V-Hz-Ph)
Temp. Range(F)
Refrigerant
Crated Weight(LBS)
Amps(A)
29.60
3
6
3
1/3
115 -60-1
32~ 42
428
5.30
24.40
3
5
3
1/3
115-60-1
32 ~ 42
348
5.30
EBC80 EBC95
Dimensions
(W x D* x H inches) 80 1/2 x 26 3/4 x 33 5/8 95 1/8 x 26 3/4 x 33 5/8
9
This manual suits for next models
4
Table of contents
Other Everest Accessories manuals
