Event Lighting STROBEXRGB User manual

RGB Strobe

Model No. STROBEXRGB

USER MANUAL

For safety, please read this user manual carefully before initial use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications within this

manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any

errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.

www.event-lighting.com.au Ver 1.0

www.event-lighting.com.au

CONTENTS

Safety Instructions

- Power input & power Linking

Product Installation

- Fuse replacement

Diagrams

- Lux chart

- Dimensions

Control Board Operation

- DMX address setting

- DMX modes setting

- Manual modes setting

- Auto run setting

- Master/slave setting

DMX chart

Technical specifications

Warranty

www.event-lighting.com.au

Safety Instructions

WARNING

•Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.

•Do not look at the light source when the device is on.

•CAUTION: This unit's housing may be hot during and after operation.

•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.

•Do not leave any flammable material within 50 cm of this unit while operating or connected to power.

•Use a safety chain when mounting this device overhead.

•Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.

•Do not operate this device if the housing, lenses, or cables appear damaged.

•Do not connect this device to a dimmer or rheostat.

•ONLY connect this device to a grounded and protected circuit.

•ONLY use the hanging bracket to carry this device.

•In case of a serious operating problem, stop using immediately.

•The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.

Power Input & Power Linking

This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.

Link up to the maximum 8A. DO NOT exceed this number.

Product Installation

This device can be mounted in many orientations provided each individual device is secured by the use of correct

mounting bracket.

Use a safety chain when mounting this device overhead.

Fuse Replacement

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au

Lux Chart

Dimensions

www.event-lighting.com.au

Menu Map

Address

<001> to <512>

DMX address

Channel

3, 6, 9, 18, 25

DMX channel modes

Option

Standard, Quiet

Select quite mode or standard mode

Monitor

(Manual

mode)

Channel 3 Mode

CH:01 to CH:03

Select DMX channel mode first, set up eachchannel

values to manual control according to DMX chart.

Channel 6 Mode

CH:01 to CH:06

Channel 9 Mode

CH:01 to CH:09

Channel 10 Mode

CH:01 to CH:10

Channel 18 Mode

CH:01 to CH:18

Channel 25 Mode

CH:01 to CH:25

Auto

Auto00

Speed <000> to <255>

Select auto program and adjust auto run speed

Auto01

Auto02

….

Auto36

Effect

on Auto

Dimmer

<000> to <255>

Adjust dimmer level and switch on strobe at different

speed for auto run

Strobe

<000> to <255>

MasMode

Yes

Master or Slave

Select master/slave mode

Master mode off

Back L

Back light always stays on

60s

Back light turns off after 60s

120s

Back light turns off after 120s

300s

Back light turns off after 300s

Temp

Temp1

XXº

Display current temperature on LED panel

Temp1

XXº

Display current temperature on chassis

Info

Test 1

Test mode without strobe

Test 2

Test mode with strobe

Reset

Yes or No

Recover to factory default

Version

Display current version

Dimmer

Control

Speed

<000> to <007>

Fade Time

DMX Address

After select the “Address” and press “Enter”, use “Up” and “Down” button to select the desired DMX address, press

“Enter”to save new setting.

DMX Modes

After select the “Channel” and press “Enter”, use “Up” and “Down” button to select the desired DMX channel mode, press

“Enter”to save new setting.

Manual Mode

It is manual control mode according to DMX chart without DMX controller.

www.event-lighting.com.au

Set up DMX channel from control panel. When fixture is in 3 DMX channel mode, you will only able to set up from Ch1 to

Ch3. When fixture is in 25 DMX channel mode, you will only able to set up from Ch1 to Ch25.

Use “Up” and “Down” button to set up each channel value from <000> to <255>, press “Enter" to save new setting.

Auto Mode

This fixture has 36 built-in programs. Entered "Auto" mode, use “Up” and “Down” button to select the built-in programs

"Auto 1 ~ Auto 36", then press the "Enter" to confirm. Use “Up” and “Down” button to select the operating speed of the

program from 000 to 255, press “Enter" to save new setting. You have to use “Effect on Auto”mode to adjust the

brightness and add strobe effect to auto run.

Effect on Auto

Use “Effect on Auto”to switch ondimmer and strobe function to auto mode. Entered “Effect on Auto” mode, use “Up” and

“Down” button to select dimmer level, then press the "Enter" to confirm. Use “Up” and “Down” button to select strobe

speed from 000 to 255, press “Enter" to save new setting.

Master/Slave Mode

Set the master fixture to auto or manual modes.

Entered “Master”mode, use “Up” and “Down” button to select “No”, press “Enter” to set fixture to slave mode.

Use DMX to link master and slave fixture together.

DMX Data

When there is a ‘*’ flashing, the StrobeX is not receiving any DMX signal. A solid ‘*’ indicated DMX signal is being

received. DMX takes priority over all other functions when a signal is being received.

Once DMX signal is lost, the StrobeX will revert back to the original setting, which also could be DMX or Manual or

Automatic mode.

DMX Chart

3 channels Mode

Channel

Value

Function

000-255

Red: 0% ~ 100%

000-255

Green: 0% ~ 100%

000-255

Blue: 0% ~ 100%

6 channels Mode

Channel

Value

Function

000-255

Master dimmer

000-255

Strobe speed and repetitions

000-255

Strobe interval (0 = longest, 255 = shortest)

000-255

Random strobe

000-255

Special effect

000-255

Speed of special effect

www.event-lighting.com.au

9 channels Mode

Channel

Value

Function

000-255

Master dimmer

000-255

Red: 0% ~ 100%

000-255

Green: 0% ~ 100%

000-255

Blue: 0% ~ 100%

000-255

Strobe speed and repetitions

000-255

Strobe interval (0 = longest, 255 = shortest)

000-255

Random strobe

000-255

Special effect

000-255

Speed of special effect

10 channels Mode

Channel

Value

Function

000-255

Master dimmer

000-255

Red: 0% ~ 100%

000-255

Strobe interval for red

000-255

Green: 0% ~ 100%

000-255

Strobe interval for green

000-255

Blue: 0% ~ 100%

000-255

Strobe interval for blue

000-031

No function

032-063

Red

064-095

Red + green

096-127

Green

128-159

Green + blue

160-191

Blue

192-223

Red + blue

224-255

Red + green +blue

000-255

Special effect

000-255

Speed of special effect

18 channels Mode

Channel

Value

Function

000-255

Master dimmer

000-255

Block 1 red

000-255

Block 1 green

000-255

Block 1 blue

000-255

Block 2 red

000-255

Block 2 green

000-255

Block 2 blue

000-255

Block 3 red

000-255

Block 3 green

000-255

Block 3 blue

www.event-lighting.com.au

000-255

Block 4 red

000-255

Block 4 green

000-255

Block 4 blue

000-255

Strobe on duration

000-255

Strobe rate

000-255

Random strobe

000-255

Special effect

000-255

Speed of special effect

25 channels Mode

Channel

Value

Function

000-255

Master dimmer

000-255

Block 1 red

000-255

Strobe rate for red

000-255

Block 1 green

000-255

Strobe rate for green

000-255

Block 1 blue

000-255

Strobe rate for blue

000-255

Block 2 red

000-255

Strobe rate for red

000-255

Block 2 green

000-255

Strobe rate for green

000-255

Block 2 blue

000-255

Strobe rate for blue

000-255

Block 3 red

000-255

Strobe rate for red

000-255

Block 3 green

000-255

Strobe rate for green

000-255

Block 3 blue

000-255

Strobe rate for blue

000-255

Block 4 red

000-255

Strobe rate for red

000-255

Block 4 green

000-255

Strobe rate for green

000-255

Block 4 blue

000-255

Strobe rate for blue

www.event-lighting.com.au

Technical Specifications

Power

•Power Consumption: 480W

•Input Voltage: 100V~240V AC, 50/60Hz

•Power Connection: PowerCON In

Photometrics

•Light Source: 968 pcs 0.8W SMD5050 RGB LEDs

•LED Beam Angle: 120°

•Output: 650 lux @3M

•PWM: 2000Hz

•LED Lifespan: 50,000 hours

Effects

•Dimming: 0 –100%

•Strobe: 1 –25 Hz

Control

•Operation: DMX, Manual, Auto Program & Master / Slave

•Display: 4-button LCD control panel

•DMX Protocol: DMX512

•DMX Channel Mode: 3 / 6 / 9 / 18 / 25

•DMX Interface: 3-pin XLR

Housing

•Housing Materials: Aluminium & ABS

•Housing Finishing: Matte Black

•Dimension: 500 x 135 x 270 mm

•Cooling: Sensor thermostat controlled variable speed fan

•Net Weight: 6.5 kg

WARRANTY

Please refer to your local dealer or please contact Event Lighting Pty Ltd

Website: www.event-lighting.com.au.

Table of contents

Other Event Lighting Dj Equipment manuals

Event Lighting

Event Lighting PARP12x8 User manual

Event Lighting

Event Lighting LM6X15 User manual

Event Lighting

Event Lighting PAR12x8A User manual

Event Lighting

Event Lighting PAN2*1*30 User manual

Event Lighting

Event Lighting PIXBAR12x3 User manual

Event Lighting

Event Lighting PANBEAM4x4x10 User manual

Event Lighting

Event Lighting PARRGBW12x8 User manual

Event Lighting

Event Lighting PRO PAR PAR12X8L User manual

Event Lighting

Event Lighting DASDI1000RGB User manual

Event Lighting

Event Lighting Fresnel User manual

Event Lighting

Event Lighting PIXBAR12x12 User manual

Event Lighting

Event Lighting M1S80W User manual

Event Lighting

Event Lighting KONTROL36 User manual

Event Lighting

Event Lighting StrobeX User manual

Event Lighting

Event Lighting PS200LECW User manual

Event Lighting

Event Lighting EL1000RGB User manual

Event Lighting

Event Lighting DARKSTAR User manual

Event Lighting

Event Lighting M1H200W User manual

Event Lighting

Event Lighting PS300IICW User manual

Event Lighting

Event Lighting CO2RGB User manual

Event Lighting

Event Lighting M19W15RGBW User manual

Event Lighting

Event Lighting PAR12x12 User manual

Event Lighting

Event Lighting M6B20W User manual

Event Lighting

Event Lighting ORBIT2 User manual

Popular Dj Equipment manuals by other brands

ALPHA LITE

ALPHA LITE ALPHA 1500 User manual book

Chauvet

Chauvet OVATION E-930VW Quick reference guide

Zumtobel

Zumtobel APHRODITE Home Instructions for use

Snow Masters

Snow Masters Zig Oscillator user manual

EuroLite

EuroLite 50530554 user manual

Beamz

Beamz BUV243 user manual

thomann

thomann Stairville DJ Lase 40-G MK-III user manual

Eagletone

Eagletone 6 Eyes Flower user manual

EuroLite

EuroLite FLD-1508 user manual

Technical Pro

Technical Pro LG8xSEA user manual

JB Systems

JB Systems Lounge Laser DMX Operation manual

Lightmaxx

Lightmaxx Vega Halo 90 user manual

Elation

Elation FUZE WASH Z350 user manual

Maverick

Maverick MK3 WASH Quick reference guide

Infinity

Infinity TF-260C7 Fresnel manual

Chauvet

Chauvet EVE E-50Z Quick reference guide

Eliminator Lighting

Eliminator Lighting E 138 manual

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC user manual