EUPRY P2T2 User manual
User Guide
May 2022
External Temperature Thermocouple Probe
(P2T2)
User Guide: External Temperature Thermocouple Probe, P2T2
Rev. 0.1 -May 2022 Page 1 of 6
Eupry ApS | Dortheavej 59. 3. | 2400 Copenhagen | www.eupry.com/ | +45 53 51 77 00 |support@eupry.com
1 Copyrights & Trademarks
Specifications and guides are subject to change without notice. Eupry is a registered trademark of
Eupry ApS. Other brands and product names are trademarks or registered trademarks of their
respective holders.
No part of the specifications and guides may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission from Eupry
ApS. Copyright © 2022 Eupry ApS. All rights reserved.
www.eupry.com
2 Content
1 Copyrights & Trademarks 2
2 Content 2
3 Introduction 3
4 Specifications 3
5 Setup of Eupry Temperature Thermocouple Probe 4
5.1 installation Guide 4
6 Product Identification 4
7 Appendix FAQ 5
7.1 I have got multiple alarms during the connection process 5
7.2 The light does not turn on when I press the Eupry Button 5
7.3 The Data Logger does not light green when I release the button 5
7.4 Where can I see the ID of the Data Logger and ID of the External Sensor Probe? 5
8 Support 5
9 Revision history 6
User Guide: External Temperature Thermocouple Probe, P2T2
Rev. 0.1 -May 2022 Page 2 of 6
Eupry ApS | Dortheavej 59. 3. | 2400 Copenhagen | www.eupry.com/ | +45 53 51 77 00 |support@eupry.com
3 Introduction
The following is a manual for the Eupry Temperature Thermocouple Probe, P2T2. The unit works with Eupry’s Data Loggers,
and all data can be viewed on the online platform, Eupry Monitoring.
4 Specifications
Temperature Operating Range
-40 °C to +1100 °C
Temperature Resolution
0.25 °C
Temperature Accuracy
Dependent on Calibration
Typical Temperature Accuracy
±10 °C
Thermal Response Time (τ)
9 s
Sensor Type
Thermocouple
Certifications
RoHS
Identification
Unique GS1 GRAI Code
Teflon cable thickness
1.5 mm
Stainless steel cap thickness
1.5 mm
Stainless steel cap length
0.5 m
Teflon cable length
1.5 m
2.5 mm jack cable
1 m
Total cable length
2.5 m
User Guide: External Temperature Thermocouple Probe, P2T2
Rev. 0.1 -May 2022 Page 3 of 6
Eupry ApS | Dortheavej 59. 3. | 2400 Copenhagen | www.eupry.com/ | +45 53 51 77 00 |support@eupry.com
5 Setup of External Temperature Thermocouple Probe
Connecting to your Eupry Data Logger
Connect the External Temperature Thermocouple Probe to the socket on the top face of a Data Logger. Make sure that the
probe is firmly pressed all the way in until you hear a clicking sound or feel a haptic feedback.
5.1 installation Guide
When installing the Temperature Thermocouple Probe, it is important to know the thermal areas of the probe, since not all of
the probe can be used at 1100 °C.
The thermal properties of the probe should be considered when installing the probe, please make sure that the probe is
installed within the temperature areas shown on the illustration below. Ensure that the temperature limits for the different
sections of the probe are not exceeded, as per the illustration below.
Illustration of the thermal areas of the probe P2T2 .
6 Product Identification
All External Sensors have two forms of identification:
Unique serial number
A unique serial number of the External Temperature Thermocouple Probe is written as text on the label of the sensor and
can be used to identify the unit in Eupry’s system.
Unique GRAI code datamatrix
A unique GRAI code identification, which also includes the serial number of the External Temperature Thermocoupler Probe
is placed on the label as a data matrix.
The entire GRAI code (GS1 standard) uniquely identifies the sensor internationally and can be used with GRAI compliant
systems.
User Guide: External Temperature Thermocouple Probe, P2T2
Rev. 0.1 -May 2022 Page 4 of 6
Eupry ApS | Dortheavej 59. 3. | 2400 Copenhagen | www.eupry.com/ | +45 53 51 77 00 |support@eupry.com
7 Appendix FAQ
7.1 I have got multiple alarms during the connection process
It is completely normal to get alarms during these processes as the sensors you are connecting are at room temperature
when first plugged in. Be aware that you do not continue to get these alarms.
7.2 The light does not turn on when I press the Eupry Button
Look at the user manual for the Data Logger on support.eupry.com.
7.3 The Data Logger does not light green when I release the button
Look at the user manual for the Data Logger on support.eupry.com.
7.4 Where can I see the ID of the Data Logger and ID of the External Sensor
Probe?
We have two kinds of barcode labels. The two pictures below illustrate where the ID can be found.
The ID of this Data Logger is the last four digits on the side of the Data Logger. The ID of the sensor is the digits on it (see
figure).
The ID of this Data Logger is the last five digits on the side of the Data Logger. The ID of the sensor is the digits on it (see
figure).
8 Support
Please visit the Eupry Support Centre for any support enquiries. This can be accessed by selecting the “Support” button when
logged in to the Eupry Monitoring.
Alternatively, please contact support using the information provided in the footer.
User Guide: External Temperature Thermocouple Probe, P2T2
Rev. 0.1 -May 2022 Page 5 of 6
Eupry ApS | Dortheavej 59. 3. | 2400 Copenhagen | www.eupry.com/ | +45 53 51 77 00 |support@eupry.com
9 Revision history
Revision
Date
Responsible
Change
0.1
17-May-2022
NHP
First revision.
User Guide: External Temperature Thermocouple Probe, P2T2
Rev. 0.1 -May 2022 Page 6 of 6
Eupry ApS | Dortheavej 59. 3. | 2400 Copenhagen | www.eupry.com/ | +45 53 51 77 00 |support@eupry.com
Table of contents
Other EUPRY Accessories manuals
