ETI 54677441 User manual
USE AND CARE GUIDE
4 FT. LED HIGH OUTPUT WRAP LIGHT
Questions, problems, missing parts?
Call ETi SSL Customer Service
9 a.m. – 5 p.m., EST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
THANK YOU
We appreciate the trust and confidence you have placed in ETi through the purchase of this LED light. We strive to continually create quality
products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing ETi!
Model #
54677441
Part #
WR-4-57-940-MV-D
2
Table of Contents
Table of Contents ...................................2
Safety Information ..................................2
Warranty ..........................................2
Pre-Installation.....................................3
Planning Installation ...............................3
Tools Required ....................................3
Package Contents .................................4
Hardware Included.................................4
Installation ........................................5
Care and Cleaning .................................10
Troubleshooting ...................................10
Safety Information
WARNING: Carefully read and understand the information
given in this manual before beginning the assembly and
installation. Failure to do so so could lead to electric shock,
fire, or other injuries which could be hazardous or even fatal.
WARNING: Ensure the electricity to the wires you are
working on is shut off. Either remove the fuse or turn off the
circuit breaker.
WARNING: Changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTICE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15B of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
ƑReorient or relocate the receiving antenna.
ƑIncrease the separation between the equipment and the receiver.
ƑConnect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
ƑConsult the dealer or an experienced radio/TV technician for help.
Warranty
This product is warranted for a period of 5 years from the date of original purchase against defects in materials and workmanship. If this
product should fail to operate due to defects in material or workmanship within 60 months of purchase, see www.ETiSSL.com for details.
This product will be repaired or replaced, at ETi’s option. This warranty is expressly limited to repair or replacement of product, and liability
for direct, incidental, or consequential damages is hereby expressly excluded. Some states do not allow exclusions of direct, incidental or
consequential damages, so the above limitation of exclusion may not apply to you. This warranty gives the consumer specifc legal rights,
which vary from state to state. WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS MANUFACTURED.
3
Please contact 1-855-384-7754 or further assistance.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
Pre-Installation
PLANNING INSTALLATION
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with the package
contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service
for replacement parts.
NOTE: Keep your receipt and these instructions for proof of purchase.
TOOLS REQUIRED
Wire
Strippers
Safety
Goggles Ladder Gloves
Flathead
Screwdriver
Phillips
Screwdriver
Power Drill
with drill bits
Wire
Cutters
NOTE: Two people are recommended for the installation of this light fixture.
www.ETiSSL.com
4
PACKAGE CONTENTS
Part Description Quantity
A LED Wrap Light Housing 1
B LED Wrap Light Diffuser 1
B
Part Description Quantity
AA Mounting Bracket 1
BB Gasket 1
CC Single Wire Connector 5
DD Electrical Box Screw 2
EE Drywall Anchor 4
FF Mounting Screw 4
HARDWARE INCLUDED
AA
NOTE: Hardware not shown to actual size.
Pre-Installation (continued)
A
BB CC
DD EE FF
5
Please contact 1-855-384-7754 or further assistance.
1 Separating the diffuser from the housing
ƑPress down gently on one end of the diffuser (B) until you meet with resistance from the bottom of the end cap of the housing (A).
ƑSlide the diffuser (B) toward the end being pressed down.
ƑLift the diffuser (B) from the other end, removing it from the housing (A).
2 Marking the mounting location
ƑWith help from another person, temporarily
hold the fixture housing (A) up to the ceiling to
determine the best mounting position and which
knockout hole to use for wiring the fixture.
ƑMark four keyhole locations for mounting.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the
circuit breaker before removing the existing light fixture or installing the new one.
Installation
Select a suitable location that can support the weight of the fixture. Determine the method of mounting before drilling.
With power disconnected to your electrical box, remove the existing fixture. Make a sketch of how the current fixture is wired (by wire
color) or mark the wires with masking tape and a pencil so you will know how to properly reconnect the wires to the new LED light fixture.
B
Keyholes
A
Knock out holes
B
www.ETiSSL.com
6
Installation (continued)
AA
ƑFeed the electrical connection wires through any knock
out hole and then through the mounting bracket (AA). The
connection wires can be held in place by the metal tabs,
if needed.
3 Feeding the wires
NOTE: Put the gasket (BB) on any knock out hole of the fixture to better protect the wires.
4 Connecting the wires
ƑConnect the hot and neutral (black and white) wires from the housing (A) to the same color wires from the
electrical box.
ƑCover the wire connection using the single wire connector (CC).
ƑConnect the green wire from the housing (A) to the grounding wire from the electrical box. Secure together
using a single wire connector (CC).
BB
Metal tabs
Knock out holes
CC
AA
A
7
Please contact 1-855-384-7754 or further assistance.
Installation (continued)
5 Attaching the housing to the ceiling
ƑDrill a 1/8 in. pilot hole into the screw locations marked on the ceiling. You can also use an awl or nail to dimple the screw holes.
ƑInstall a drywall anchor (EE) and a mounting screw (FF) in each drilled mounting hole, but do not tighten fully.
ƑAlign the 4 mounting keyholes on the housing (A) with the 4 mounting screws in the ceiling. Once the screw heads are through the
large ends of the keyholes, slide the housing until the heads of the screws slide into the narrow ends of the keyholes.
ƑFinish tightening the mounting screws (FF) until the fixture housing (A) is tightly secured to the mounting surface.
NOTE: The drywall anchors (FF) are only to be used for mounting the fixture onto plaster or drywall surfaces.
EE
FF
A
AA
www.ETiSSL.com
Purple(+)
Black(+)
White(-)
Green(E)
Anode(+)
Gray(-)
Cathode(-)
Connect the black wire and wire L together.
Connect the white wire and wire N together.
Connect the green wire and earth wire together.
Connect the purple wire and the anode of the dimmer, and connect the gray wire and the cathode of the dimmer.
Finally, fix all of them with single wire connector (CC).
□
□
□
□
□
Dimmer
0-10V
-
LED Power (DRIVER)
DIM+
DIM+
DIM-
LED lamp panel
LED+
LED-
N
L
NOTE: Please refer to below wire and curcuit diagram if end user has demand for the 0-10V dimmer installation.
Installation (continued)
6 Attaching the diffuser to the
housing
ƑInsert one end of the diffuser (B) into the
end cap of the housing (A) to the bottom of
the limit part.
ƑPush the other end of the diffuser (B) to the
top of the limit part on the opposite end cap.
ƑRestore power to the electrical box.
Turn on the light switch on to activate the fixture.
B
A
Limit part
8
When the sensor is 0-10V step-dimming with LED power supply, circuit wiring diagram is as below.Ƒ
0-10V LED Power (DRIVER)
drive+
drive-
DIM+
DIM-
DIM+
DIM-
N
N
L’
L
N
L
Step-dimming
Motion Sensor LED lamp panel
LED+
LED-
NOTE: This wrap light is compatible for motion sensor, and below circuit wiring diagram is for two types of motion sensor. For the sensor, we
suggest to use ETI SSL brand model: 90600145 (ON/OFF) and 90600144 (0-10V).
LED+
LED- 0-10V
Motion Sensor
L’ (Black)
L (Black)
N (White)
N (White)
LED DRIVER
B+ (Anode)
B- (Cathode)
9
When the sensor is ON/OFF (also plus LED power supply), circuit wiring diagram is as below.
Ƒ
NL’
N
L
NL
Motion Sensor
（ON/OFF）LED Power (DRIVER)
drive+
drive-
DIM+
DIM-
LED lamp panel
LED+
LED-
LED+
LED-
L’ (Black) L (Black)
N (White) N (White)
(ON/OFF)
Motion Sensor
LED DRIVER
B+ (Anode)
B- (Cathode)
Please contact 1-855-384-7754 or further assistance.
www.ETiSSL.com
10
Care and Cleaning
CAUTION: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from
the fuse box.
ƑClean the fixture with a soft, dry cloth.
ƑDo not use cleaners with chemicals, solvents, or harsh abrasives.
ƑDo not use liquid cleaner on the LEDs, LED driver, or wiring inside the light fixture.
Troubleshooting
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.
Minor problems often can be fixed without the help of an electrician.
Problem Possible Cause Solution
The fixture will not light. The power is off. Ensure the power supply is on.
The circuit breaker is off. Ensure the circuit breaker is in the on position.
There is a bad connection. Check to ensure proper wire connections are made. Contact a
qualified electrician.
There is a defective switch. Contact a qualified electrician.
The fuse blows or the circuit
breaker trips when the light is
turned on.
The wires are crossed or the
power wire is grounding out. Check the wire connections.
Contact a qualified electrician or call ETiSSL customer service
1-855-348-7754.
Questions, problems, missing parts?
Call ETi SSL Customer Service
9 a.m. – 5 p.m., EST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
Retain this manual for future use.
This manual suits for next models
1
Table of contents
Languages:
Other ETI Light Fixture manuals
Popular Light Fixture manuals by other brands
Emos
Emos CLASSIC ZY1431T manual
Westinghouse
Westinghouse Outdoor Lighting Fixture owner's manual
Hedler
Hedler C 12 silent Operation manual
Blizzard Lighting
Blizzard Lighting Puck: CSI manual
Energetic Lighting
Energetic Lighting ELYSL-5004 Series installation instructions
Lightmaxx
Lightmaxx Shaft 5R user manual
Cooper Lighting
Cooper Lighting Halo L3232E Specification sheet
Stageline
Stageline ODW-2410RGBW instruction manual
Light Sky
Light Sky Tornado Series user manual
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U specification
Lightolier
Lightolier Lytespan 83ED17S specification
Lightolier
Lightolier Calculite CS8226 specification