ESI ESRTP5 User manual
ESRTP5
Programmable Room
Thermostat
Installation Instructions
Thank you for choosing ESi Controls.
All our products are tested in the UK so we are
confident this product will reach you in perfect
condition and give you many years of service.
However, for additional peace of mind, we
recommend you register your product online at
www.esicontrols.co.uk/warranty for your
extended warranty.
2
Installation Instructions
1. Technical Specification
1.1 Parameter Settings 6
1.2 Thermostat Technical Settings 7
2. Installation Instructions
2.1.1 Installation Safety Instructions 8
2.1.2 General Safety Instructions 8
2.1.3 Warning Notices 8
2.1.4 Maintenance 9
2.2.1 Fitting the Programmable Room
Thermostat 9
2.2.2 Installing the Programmable Room
Thermostat 10
2.2.3 Wiring Diagram 11
3. Technical Settings (tEcH)
3.1 Quick Comand Guide 12
3.2 Menu Technical Settings (tEcH) 13
4. Landlord Service (SEr)
4.1 Setting the Landlord Service (SErS) 14
4.2 Setting the Due Date (DAtE) 15
4.3 Changing the Password (CODE) 15
Contents
3
4
5
Installation Instructions
6
All Day Mode
All ay mode temperature 5°C-35°C (Default: 21°C)
Holiday Mode
Holiday mode temperature 5°C-35°C (Default: 7°C)
Holiday mode days 1-99 days (Default: 1 day)
Default Mode
Temporary set temperature 5°C-35°C (Default: 21°C)
Program event start time 00.00-24.00
(See section 5.1 for details)
Program event set temperature 5°C-35°C (See section 5.1 for details)
Program operation mode 5/2 day, 7 day, 24hr (Default: 5/2 day)
Number of programs 4 or 6 (Default: 4)
Manual Mode
Manual mode temperature 5°C-35°C (Default: 21°C)
Delayed Start
DS Off or On (Default: Off)
TPI
TPI Off, 3 cycles or 6 cycles (Default: Off)
OFF Mode (Frost Protection)
Frost protection start temperature 5°C
Frost protection exit temperature 7°C
Service
SERS OFF or 1-4 (Default: OFF)
(See section 9.1 for details)
Service DATE 28-366 days (Default: 365 days)
Other Functions
Operation MODE Auto, Manual, OFF (Default: Auto)
Temperature calibration ADJ -3.0°C-3°C (Default: 0°C)
SWING 0.5°C-2.0°C (Default: 0.5°C)
Display backlight Off/On (Default: Off)
1. Technical Specification
1.1 Parameter Settings
7
Power supply 230VAC, 3(1)A SPDT
Temperature sensor type +/- 1°C at 20°C
Total switch rating 3(1)A 230VAC
Contact type SPDT (Volt free changeover
contacts)
Plastic Thermoplastic, flame retardant
Protection rating IP30
Dimensions 95mm (L) x 95mm (W) x 39mm (D)
BST/GMT Time change Automatic
Factory pre-set programme yes, (See section 5.1 for details)
Complies with
EN 60730-1, EN 60730-2.7, EN
55014-1:2006+A1:2009+A2:2011,
EN 61000-3-2:2014, EN 61000-
3-3:2013, EN55014-2: 2015, EN
60730-1:2011, EMC Directive
2014/30/EU, LVD Directive
2014/35/EU
1.2 Thermostat Technical Settings
8
2. Installation
2.1.1 Installation Safety Instructions
The unit must be installed by a suitably qualified person in
accordance with the latest IEE Wiring Regulations. Isolate
mains supply before commencing installation. Please read all
instructions before proceeding.
Ensure that the fixed wiring connections to the mains supply is
via a fuse rated at not more than 3 Amps and Class ‘A’ switch
having a contact separation of a minimum of 3mm in all poles.
The recommended cable sizes are 1.0mm sqr or 1.5mm sqr. No
earth connection is required as the product is double insulated
but ensure continuity of earth throughout the system.
2.1.2 General Safety Instructions
This product complies with the essential requirements of the
following EC Directives:
• Electro-Magnetic Compatibility Directive 2014/30/EU.
• Low Voltage Directive 2014/35/EU.
• EC Marking Directive 2014/30/EU.
Please leave the user instructions with the end user where they
should be kept in a safe place for future reference.
2.1.3 Warning Notices
WARNING: Always isolate the ac mains supply before
installing. This product must be fitted by a competent
person, and installation must comply with the guidance
provided in the current editions of BS767 (IEE wiring
regulations) and part “P” of the building regulations.
9
2.1.4 Maintenance
Always isolate the mains supply before commencing any work,
servicing or maintenance on the system. And please read all
instructions before proceeding.
Arrange for an annual maintenance and inspection schedule to
be carried out by a qualified person on every part of the heating
and hot water system.
2.2.1 Fitting the Programmable Room Thermostat
The ideal position to locate the Programmable Room
Thermostat is about 1.5m above floor level, in a location where
the thermostat is accessible, reasonably lit and free from
extremes of temperature and draughts. Do not position the
thermostat near sources of heat, such as radiators, lights, TV,
direct sunlight or on an outside wall.
1.5m
10
2.2.2 Installing the Programmable Room Thermostat
1. Use a flat headed screwdriver to press the fastener at
the top of the unit, then gently loosen from the unit,
unhooking from top to bottom.
2. Fix the 35mm back box, terminals at the top, onto a
2 flange metal back box with 2 BM3.5x23 screws. If
installing on a 4 flange metal back box, simply push down
the flanges on the top and bottom to leave the flanges
on the left and right hand side.
If there are 4 flanges,
push down the top and
bottom flanges to leave
just 1 on either side.
Use a 35mm back box
with 2 screw flanges.
Other manuals for ESRTP5
2
Table of contents
Other ESI Thermostat manuals
ESI
ESI ESRTERFW User manual
ESI
ESI ESCTP5-RF User manual
ESI
ESI ESRTP5WIFI Operating instructions
ESI
ESI ESRTP4RF User manual
ESI
ESI ESRTP4+ User manual
ESI
ESI ESCTDE Operating instructions
ESI
ESI ESCTP5-RF User manual
ESI
ESI ESRTP4+ User manual
ESI
ESI ES2247B Operating instructions
ESI
ESI ESRTD3 User manual
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
