ESAB A22 POB Instructions for use
334 771--001 9611
A22 POB
Tubeplate welding tools
Simplified service manual
LIST OF CONTENTS Page
SAFETY 4...........................................................
TECHNICAL DESCRIPTON 5..........................................
INSTALLATION 6.....................................................
OPERATION 10.......................................................
MAINTENANCE 10....................................................
SELECTION TABLE 11.................................................
ACCESSORY SET FOR INTERNAL WELDING 12.........................
ACCESSORY SET FOR EXTERNAL FILLET WELDING 13.................
ACCESSORY SET FOR WELDING TITANIUM 14.........................
WORKING RANGE 15.................................................
DIMENSION DRAWING 16.............................................
DIAGRAM 17.........................................................
CONNECTION DIAGRAM 18...........................................
SPARE PARTS LIST A22 POB 21.......................................
Rights reserved to alter specifications without notice
-- 3 --mvarnen1
WARNING
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS.
TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY
PRACTICES WHICH SHOULD BE BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
SInstall and earth the welding unit in accordance with applicable standards.
SDo not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
SInsulate yourself from earth and the workpiece.
SEnsure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
SKeep your head out of the fumes.
SUse ventilation, extraction at the arc, or both, to keep fumes and gases from
your breathing zone and the general area.
ARC RAYS -- Can injure eyes and burn skin.
SProtect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
SProtect bystanders with suitable screens or curtains.
FIRE HAZARD
SSparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby.
MALFUNCTION
SCall for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE
INSTALLING OR OPERATING THE EQUIPMENT
PROTECT YOURSELF AND OTHERS!
SAFETY
-- 4 --
df00f2ea
SAFETY
Users of ESAB welding equipment have ultimate responsibility for ensuring that any-
one who works on or near the equipment observes all the relevant safety precau-
tions.
Safety precautions must meet the requirements that apply to this type of welding
equipment.
The following recommendations should be observed in addition to the standard re-
gulations that apply to the work place.
All work must be carried out by trained personnel who are familiar with the operation
of the welding equipment.
Incorrect operation of the equipment may lead to a hazardous situation which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the welding equipment must be familiar with:
Sits operation
Sthe location of emergency stops
Sits function
Srelevant safety precautions
Swelding
To make this easier each switch, pushbutton or potentiometer is marked with a
symbol or text that indicates its function when activated.
2. The operator must ensure that:
Sno unauthorized person is stationed within the working area of the equipment
when it is started up.
Sthat no--one is unprotected when the arc is struck
3. The work place must:
Sbe suitable for the purpose
Sbe free from draughts
4. Personal safety equipment
SAlways wear recommended personal safety equipment, such as safety
glasses, flame--proof clothing, safety gloves.
SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns.
5. General precautions
SMake sure the return cable is connected securely.
SWork on high voltage equipment may only be carried out by a qualified
electrician.
SAppropriate fire extinquishing equipment must be clearly marked and close
at hand.
SLubrication and maintenance must not be carried out on the equipment dur-
ing its operation.
-- 5 --cra1d1ea
TECHNICAL DESCRIPTION
The POB tube plate welding tool is intended for TIG--welding of tubes into flat tube plates.
It is suitable for all types of weld joints, in certain cases using extra equipment.
The POB 12--60 welding tool is intended for use together with a spindle and a centering mandrel
according to the selection table on page 11.
POB 12--60 is intended for use with the power sources MECHTIG 315 INVERTER,
PROTIG 315 INVERTER, PROTIG 250 and PROWELDER 250
TECHNICAL DATA A22 POB
Max. continuous welding current 180 A/60 %
Max. pulsed welding current 200 A/60 %
Working range:
base specification
with titanium welding kit
with external fillet welding kit
with internal welding kit
12--60 mm
12--60 mm
12--60 mm
according to designation
Electrode angle for:
butt welding
internal fillet welding
external fillet welding
internal welding
(See page 15)
parallel with tube axis
30_to tube axis
15_to tube axis
90_to tube axis
Electrode diameter 1.6 and 2.4 mm
Speed of rotation 0.3--4.5 r.p.m
Wire feed speed 0.15--1.5 m/min
Wire diameter 0.8 and 0.91 mm
Length of welding cable 8m
Weight
tool
cable and hose bundle
4.5 kg
4.5 kg
Order no.
POB 12--60, base version with wire feed unit 333 893--881
Base version can be fitted with accessory kits for
-- external fillet welding
-- titanium welding
-- internal welding diameter:
9.5--15 mm
15--20 mm
20--30 mm
333 897--880
441 000--880
441 131--880
441 132--880
441 133--880
dra1b003
When ordering an accessory set for internal welding, please indicate both the inner diameter
(D) of the tube and the distance of the welding joint to the outside (A) of the plate.
-- 6 --
cra1d1ea
INSTALLATION
1. Welding power source, see separate instruction manual.
2. Dimension drawing, see page 16.
3. Diagram, see page 17.
4. Connection diagram, see page 18 and page 19.
5. Tool dismantling:
It is necessary to dismantle the tool.
SFor adjustment of the ”home” position.
SIn the event of a fault.
Dismantling:
SRemove the three bolts (1) in the support ring (2).
SRemove the screw (4).
SPull off the support tube (3).
SCarefully withdraw the entire inner assembly (5) backwards, being careful not to
damage the microswitch.
-- 7 --cra1d1ea
6. Adjusting the ”home” position:
SRemove the four bolts (7).
SWithdraw the gear ring. The lifting cog influencing the microswitch can now be
moved a full turn in 22˚, 5 steps, starting at 11˚, 25 counted from 12 o’clock.
7. Tool reassembly:
SInsert the inner assembly (5) in the outer casing (6). Make sure that the microswitch
is not located just opposite the lifting cog.
SRotate the parts slightly relative to one another, so as to engage the motordrive gear
and the gear ring.
SFit the support tube (3), (lightly grease the contact surface of the sealing ring with a
suitable grease, e.g. Barrierta). Fit the support plate (2) with the screws (1).
SFit the screw (4).
-- 8 --
cra1d1ea
8. Replacement and fitting of the electrode:
SCut off the electrode to some 45 mm and grind it to the desired angle.
SRemove the gas cup (3).
SRemove the electrode nozzle (2) and the electrode nozzle with gas lens.
SReplace the electrode. When changing to a different electrode diameter it is necess-
ary also to change the electrode nozzle (2) and the collet (1).
dra1b001
The adjustment of the electrode is important to guarantee the repeatability for continued
welding.
Use ready--ground electrodes of the same length and fit them in the same position.
dra1b002
-- 9 --cra1d1ea
9. Adjustment of the welding diameter:
SSlacken the locking screw (8).
SUse a screwdriver to turn the gear wheel (7),
which is mounted on the link arm (3), so
that the correct welding circle diameter is
obtained.
SSlacken the screw (4).
SAdjust the electrode angle by rotating
the electrode holder (6).
STighten the locking screws (4 and 8).
10. Adjusting the arc length:
SAdjust the length of the arc (i.e. the
distance between the tip of the
electrode and the workpiece) by
screwing the spacing tube (9) in or out.
SSecure the setting by means of the
locking nut (10).
11. Inserting the filler wire:
SCut off any bent length of the wire
and file off the end.
SFeed the wire into the nozzle.
SAdvance the wire through the tool
(by running the feed unit manually).
12. Replacing the wire nozzle:
SUndo the screw (5) and remove the nozzle,
which is threaded on to the wire guide.
13. Replacing the wire guide:
SDismantle the tool.
SRemove the wire nozzle from the wire
guide and remove the wire guide from the
inner part of the tool.
SScrew the internally bevelled end of the
new wire guide into the feed unit.
SFit the wire nozzle.
SMount the tool.
-- 1 0 --
cra1d1ea
OPERATION
The POB tube welding tool connected to the programmable welding power
source PROTIG 250, PROWELDER 250, PROTIG 315 INVERTER or
MECHTIG 315 INVERTER:
SSet all the welding parameters on the programmable PROTIG 250, PROWELDER 250,
PROTIG 315 INVERTER or MECHTIG 315 INVERTER power source unit.
SAdjust the position and the angle of the electrode.
SStart the automatic welding sequence by pressing the ”Start” button on the power source
or directly on the POB tube welding tool.
dra1b004
It is important that the tool is suspended according
to the adjoining figure.
For balancing to weightlessness a counterbalancing
device is used. Ordering number 332 330--005
MAINTENANCE
SClean the tool as necessary.
SCheck wearing parts at regular intervals and replace as necessary.
SCheck that all hoses and connections for gas, water, welding current and control current
are undamaged and correctly connected.
SCheck that the correct electrode is being used and that it is properly ground.
By separating the inner and outer parts from each other the equipment is easy to service.
Table of contents
Other ESAB Welding System manuals
ESAB
ESAB fabricator 141i User manual
ESAB
ESAB Retrofit Aristo Mig 4004i WeldCloud User manual
ESAB
ESAB THERMAL DINAMICS CUTMASTER 60i User manual
ESAB
ESAB Thermal Dynamics CUTMASTER 40 User manual
ESAB
ESAB A6TF F1 User manual
ESAB
ESAB A6 SFD1 Series User manual
ESAB
ESAB Aristo RoboFeed 3004w User manual
ESAB
ESAB Powercut 900 User manual
ESAB
ESAB Origo Mig C170 3ph User manual
ESAB
ESAB LPH 120 User manual
ESAB
ESAB ESP-150 User manual
ESAB
ESAB Rustler EM 280C PRO User manual
ESAB
ESAB MIG400iCCCV User manual
ESAB
ESAB Origo Arc 250 User manual
ESAB
ESAB EMP 285ic 1ph User manual
ESAB
ESAB ARC250i User manual
ESAB
ESAB Multimaster-260 Owner's manual
ESAB
ESAB MultiPower 460 Pulse User manual
ESAB
ESAB LTG 410 User manual
ESAB
ESAB Aristo Arc 4000i User manual
Popular Welding System manuals by other brands
TAFA
TAFA 30*8B35 owner's manual
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Technical specifications
CIGWELD
CIGWELD 636804 use instructions
Red-D-Arc
Red-D-Arc DC-400 Operator's manual
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 owner's manual
Elettro
Elettro HI-MIG 3000 SYNERGIC instruction manual
