Equinox Systems Lexor User manual
Order code: EQLA41
User manual
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
Equinox Lexor Laser Safety
Equinox Lexor Laser Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
You should nd inside the Laser carton the following items:
1, Lexor Laser 2, Power cable 3, Instruction manual
Technical Specications:
DMX channels: 7
Laser diode: 1 x 150mW Red (650nM),
1 x 100mW Blue (450nmM)
Micro-stepping motor scanner with extra wide scanner angle
Operating modes: 1, Sound Activated
2, Auto Run
3, DMX
Power consumption: 21W
Power supply: 240V
Dimensions: 255 x 213 x 164mm
Weight: 2Kgs
Fuse: 2A
Features:
The Lexor features 7 DMX channels and many laser patterns that are ideal with or without fog.
Equinox Lexor Laser Technical specications
Rear view:
Identication:
1, Keylock
2, Cooling fan
3, DMX In
4, DMX out
5, Audio sensitivity knob
6, Dip switches
7, Microphone
8, Power input
9, Fuse
10, DMX LED
Operation modes:
The Lexor has three modes of operation as follows:
1, Sound active mode
To select sound active mode set dip switch 10 to ON and all others to OFF. You can now use
the sensitivity control on the back panel to set the required sound level. After 8 - 10 seconds
without any music, the laser diodes will turn OFF and will come back ON as soon as the music
starts again.
2, Auto mode
To select auto mode, set dip switches 9 + 10 to the ON position and all others to OFF. The
Lexor will now display all it’s internal programmes. In this mode the laser diodes will remain on
constantly until the power is turned OFF or the mode is changed.
3, DMX mode
To select DMX mode, set dip switch 10 to OFF. You can now set the required DMX address using
dip witches 1 to 9. Please refer to the chart below for DMX functions.
DMX function chart:
Equinox Lexor Laser Operation modes
Channel Value Function
CH1
CH3
CH4
CH5
CH6
CH2
CH7
0-49
50-99
100-149
150-199
Blackout
Manual static pattern mode
Manual dynamic pattern mode
Sound active
200-255 Auto mode
0-255
0-255
0-255
0-255
0-255
Pattern selector
Position Y adjustment
Position X adjustment
Scanning speed (fast to slow)
Dynamic pattern speed (fast to slow)
0-255 Static pattern size (small to big)
DMX Control Mode
Operating in a DMX control mode environment gives the user the greatest exibility when it comes
to customising or creating a show. In this mode you will be able to control each individual trait of
the xture and each xture independently.
Setting the DMX address
The DMX mode enables the use of a universal DMX controller. Each xture requires a
“start address” from 1- 511. A xture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a xture that occupies or uses 7
channels of DMX and was addressed to start on DMX channel 100, would read data from
channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used
do not overlap. E.g. the next unit in the chain starts at 107.
Set the start address using the group of dip switches located usually on the back of the xture.
Each dip switch has an associated value. Adding the value of each switch in the ON position will
provide the start address. Determining which switches to toggle ON given a specic start address
can be accomplished in the following manner. By subtracting the largest switch value possible
from the selected start address until zero is achieved.
Equinox Lexor Laser DMX control mode
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent xtures and controllers. A DMX controller sends DMX data instructions form the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have
a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the
shortest cable path possible. The order in which xtures are connected in a DMX line does not
inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The Equinox Lexor laser can be controlled via DMX-512 protocol. The DMX address is set on
the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for
data input/output (gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Equinox Lexor Laser DMX set up
Further DMX cables can be purchased from all
good sound and lighting suppliers or Prolight
dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Equinox Lexor Laser DMX Set Up
Equinox Lexor Laser Dip Switch Reference Chart
DMX Dip Switch Quick Reference Chart
Dip Switch Position
Class 3B Laser Lighting Effect User Safety Guide ProLight Concepts Limited
Installation and Operation Notes
1. The laser should only be installed and operated by those that are aware of how
to operate laser, and what the various controls perform. The keyswitch provided
on the laser should help to prevent use by unintended people.
2. The laser should be mounted in a suitable and secure position in the venue, so
that once in position it is unlikely to be affected by unintended movement.
3. Prior to installation and operation of the laser, the paths of the beams and
effects should be considered, particularly with respect to how they will touch the
audience. If direct audience scanning is desired then the laser energy in the
effects needs to be considered to decide if the effects are safe for direct
viewing.
Introduction
Laser lighting products are used to create some of the most vivid and striking visual effects, and
are often noted for how they seem to produce solid shapes that cut through the air, and pick up
highly dened swirling smoke patterns. The light that is used to create these stunning effects is
different from normal light and therefore several precautions need to taken when using lasers to
ensure that the lighting effects are safe and enjoyable to view. The optical power output from the
kind of lasers used for lighting displays can be harmful if not properly setup or is misused. But
when used following the recommended health and safety guidelines, laser lighting effects no more
harmful than looking at any conventional lighting effect.
This guide has been put together to provide you with some background information about laser
safety, and guidance on the recommended health and safety requirements for using lasers in
public places. Although this guide covers the main points to consider when using laser effects,
users are advised to familiarise themselves with other guidance, particularly that issued by the
Health and Safety Executive, HS(G)95 The Radiation Safety Of Lasers Used For Display
Purposes, which is freely downloadable from the HSE website. Attending one of the laser safety
training courses, listed at the end of this guide, is also highly recommended.
Equinox Lexor Laser Safety
Important Warnings
Class 3B Lasers have the potential to harm eyesight if viewed directly in the face, and
in many instances this may be the case, even if viewed over longer distances of several
tens of metres. Therefore before using the laser product you should familiarise yourself
with its operation, and also the safety aspects that need to be considered.
Laser lighting effects are quite safe to watch if installed and used correctly, and being
aware of a few basic factors will help you to achieve this. This guide has been prepared to
help provide a basic backgrounder to the key safety aspects, and is based on current UK
health and safety guidance on the use of lasers for public displays.
Table of contents
Other Equinox Systems Lighting Equipment manuals
Equinox Systems
Equinox Systems Fusion 150 User manual
Equinox Systems
Equinox Systems Goboceptor User manual
Equinox Systems
Equinox Systems CAPRICORN EQLA22 User manual
Equinox Systems
Equinox Systems FLAM11 User manual
Equinox Systems
Equinox Systems EQLED032A User manual
Equinox Systems
Equinox Systems Fusion 260ZR User manual
Equinox Systems
Equinox Systems GEMINI User manual
Equinox Systems
Equinox Systems EQLED65 Giga Bar System User manual
Equinox Systems
Equinox Systems Lighting strike STRO21 User manual
Equinox Systems
Equinox Systems NEBULA User manual
Equinox Systems
Equinox Systems LED Par 64 User manual
Equinox Systems
Equinox Systems QUADZILLA User manual
Equinox Systems
Equinox Systems SpectraPix Lithium Batten User manual
Equinox Systems
Equinox Systems QUADRILLE User manual
Equinox Systems
Equinox Systems Interceptor MKII User manual
Equinox Systems
Equinox Systems SCORPIO EQLA11 User manual
Equinox Systems
Equinox Systems ARIES EQLA20 User manual
Equinox Systems
Equinox Systems Nova Par 64 User manual
Equinox Systems
Equinox Systems Krypton EQLED21 User manual
Equinox Systems
Equinox Systems KAMIKAZE EQLA14 User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
