Epson FX-2180 - Impact Printer User manual
9-Pin Dot Matrix Printer
Loading Continuous Paper Onto the Front
Push Tractor . . . . . . . . . . . . . . . . . . 2
Loading Continuous Paper Onto the Rear
Push Tractor . . . . . . . . . . . . . . . . . . 4
Removing the Printed Document From
the Push Tractor . . . . . . . . . . . . . . . . 6
Removing Continuous Paper With Labels . . . 7
Replacing the Ribbon Cartridge . . . . . . . . 8
Clearing Paper Jams . . . . . . . . . . . . . . . 14
If Your Printer Stops Printing Unexpectedly . . . 16
EPSON is a registered trademark of SEIKO EPSON CORPORATION. Other product names used herein
are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims
any and all rights in those marks.
Contents
Quick Reference
Guide
®
Read your
User’s Guide
first for
complete instructions, and then
use this guide any time you want
to quickly find information about
the topics on the right.
Open the front paper guide by
pulling the tab at the center of it, and
then remove the guide by grasping
both sides and pulling it straight out
of the printer.
Open both sprocket covers, and fit
the first four holes of the paper,
printable side up, over the tractor
pins. Then close the sprocket covers.
Note:
Load continuous paper that has a clean,
straight edge to avoid paper jams.
tab
Loading Continuous Paper Onto the Front Push Tractor
12
2
To load continuous paper onto the front push tractor, follow these steps:
To remove any paper from the paper
path, press the Load/Eject button.
The printer feeds the paper into the
standby position, where you can
remove the paper from the printer.
If you load continuous paper of a
different size or thickness, you need
to adjust the position of the sprockets
or change the paper thickness lever
setting. See Chapter 2 of the User’s
Guide for instructions.
Attach the front paper guide by
inserting it into the slots in the
printer as shown.
Close the front paper guide, and
make sure the paper release lever is
set to the front push tractor position.
Note:
Always close the printer cover before printing.
The printer does not print when the cover is
open.
Loading Continuous Paper Onto the Front Push Tractor
3
3 4
When you load continuous paper with
labels, make sure that the auto
tear-off mode is off before you start
to print. If you feed continuous
labels backward, the labels may
come off the backing sheet and jam
the printer.
To turn off the auto tear-off mode,
enter the printer’s default-setting
mode. See Chapter 5 of the User’s
Guide for instructions.
Open the paper guide cover and
remove the paper guide.
Open both sprocket covers, and fit
the first four holes of the paper,
printable side down, over the tractor
pins. Then close the sprocket covers.
Note:
Load continuous paper that has a clean,
straight edge to avoid paper jams.
paper guide
paper guide cover
Loading Continuous Paper Onto the Rear Push Tractor
4
1 2
To load continuous paper onto the rear push tractor, follow these steps.
cCaution:
Do not load continuous paper with labels onto the rear push tractor; the labels may come off the
backing sheet and jam the printer.
To remove paper from the paper path,
press the Load/Eject button. The
printer feeds the paper to the
standby position, where you can
remove the paper from the printer.
If you load continuous paper which
is a different size or thickness, you
need to adjust the position of the
sprocket units or change the paper
thickness lever setting. See Chapter 2
of the User’s Guide for instructions.
Attach the paper guide. Close the paper guide cover, and
make sure the paper release lever is
set to the rear push tractor position.
Note:
Always close the printer cover before printing.
The printer does not print when the cover is
open.
Loading Continuous Paper Onto the Rear Push Tractor
5
3 4
Make sure the Tear Off/Bin lights are
flashing. (You may need to press the
Tear Off/Bin button.) When the Tear
Off/Bin lights are flashing, your
paper is in the tear-off position.
from the front push tractor from the rear push tractor
Removing the Printed Document From the Push Tractor
6
To remove the printed document from the front or rear push tractor, follow the steps below. To
remove continuous paper from the pull tractor, see Chapter 2 of the User’s Guide.
1
When you resume printing, the printer
automatically feeds the paper
backward to the top-of-form
position, and starts printing.
To feed the continuous paper
backward from the tear-off position
to the standby position, press the
Load/Eject button.
2
Open the paper guide cover, and tear off the printed document using
the printer’s tear-off edge.
Make sure that the printer finishes
printing. You may need to press the
Pause button to stop printing.
(When the printer is paused, the
Pause light is on.)
Tear off the fresh supply of
continuous labels at the perforation
nearest the paper entry slot.
Hold down the LF/FF button to eject
the remaining labels from the printer.
cCaution:
When printing on labels, never press the
Load/Eject or Tear Off/Bin button.
When fed backward, labels can easily
come off the backing sheet and cause a
paper jam.
Removing Continuous Paper With Labels
7
Removing the Printed Document From the Push Tractor
Removing Continuous Paper With Labels
To avoid peeling labels off the backing sheet and jamming the printer, follow the steps below
when you remove continuous paper with labels from the front push tractor.
1
23
Press the Operate button to turn off
the printer. The printer is off when
the surface of the Operate button is
even with the button protectors as
shown.
cCaution:
Moving the print head while the printer
is on may damage the printer.
Unplug the printer from the electrical
outlet.
Open the paper guide cover. Then lift
the printer cover by its back edge and
pull it straight up and off the printer.
Replacing the Ribbon Cartridge
8
To replace the ribbon cartridge, follow the steps below.
wWarning:
You will need to move the print head by hand to replace the ribbon cartridge. If you have just used
the printer, the print head may be hot; let it cool for a few minutes before touching it.
13
2
Make sure the print head is not hot; if
it is, let it cool for a few minutes
before touching it. Then slide the
print head to the ribbon installation
position (the indented portion of the
paper tension unit) by hand.
Grasp the used ribbon cartridge and
pull it up and out of the printer.
9
Replacing the Ribbon Cartridge
4 5
When you use the pull tractor, you can
replace the ribbon cartridge even
though the print head is not in the
ribbon installation position.
Remove the separator from the new
ribbon cartridge and discard it. Then
turn the ribbon-tightening knob in
the direction of the arrow to remove
any slack in the ribbon.
Hold the cartridge with the
ribbon-tightening knob up. Fit the
two notches nearest you (á) over the
small pegs on each side of the printer
as shown. Then lay the cartridge flat
so that the other notches (í) fit over
the corresponding pegs.
separator
ribbon-tightening knob
Replacing the Ribbon Cartridge
10
6 7
Other manuals for FX-2180 - Impact Printer
4
Table of contents
Other Epson Printer manuals
Epson
Epson L200 User manual
Epson
Epson SC-P600 series Instruction Manual
Epson
Epson SureColor F6000 Installation instructions
Epson
Epson Inkjets User manual
Epson
Epson Disc Producer PP-100AP User manual
Epson
Epson Stylus PHOTO 1290 User manual
Epson
Epson ET-3750U User manual
Epson
Epson TM-H6000IV User manual
Epson
Epson SC-F3000 Series User manual
Epson
Epson Stylus Color 800 Dimensions
Epson
Epson Stylus Photo R3000 Series User manual
Epson
Epson Stylus Pro 9890 Series User manual
Epson
Epson R1900 - Stylus Photo Color Inkjet Printer User manual
Epson
Epson WorkForce Pro WP-4023 Manual
Epson
Epson Stylus Photo R3000 Series User manual
Epson
Epson Stylus Pro 7900 User manual
Epson
Epson Stylus Pro 5000 User manual
Epson
Epson Ecotank ET-2721 User manual
Epson
Epson TM-H5000II series User manual
Epson
Epson LX-810 User manual
