Empire Comfort Systems BP)-1 Quick start guide

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

Mantis

PowerHumidifierBurnersExhaust

Fan

Blower

Med

Low

FrontRear

POWER-VENT

HIGH-EFFICIENCY

FIREPLACE WITH

BAY WINDOW

MODELS

PV-28SV50-(BN,BP)-1

PV-28SV55-(CN,CP,GN,GP)-1

WARNING: If not installed, operated and main-

tained in accordance with the manufacturer’s in-

structions, this product could expose you to sub-

stances in fuel or from fuel combustion which can

cause death or serious illness.

Installer: Leave this manual with the

appliance.

Consumer: Retain this manual for future

reference.

— Do not store or use gasoline or other ﬂamma-

ble vapors and liquids in the vicinity of this or

any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

— Installation and service must be performed

by a qualiﬁed installer, service agency or the

gas supplier.

WARNING: If the information in these in-

structions are not followed exactly, a ﬁre or ex-

plosion may result causing property damage,

personal injury or loss of life.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

state or local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

™

EMPIRE

Comfort Systems

This appliance is NOT to be installed in Canada.

22618-17-0308Page 2

TABLE OF CONTENTS

Important Safety Information ......................................................................................................................................... 3

Safety Information for Users of LP-Gas ......................................................................................................................... 4

Requirements for Massachusetts ..................................................................................................................................... 5

Gas Supply ...................................................................................................................................................................... 6

Introduction ..................................................................................................................................................................... 7

Installation Instructions – General Safety Information ................................................................................................... 8

Speciﬁcations .................................................................................................................................................................. 8

Clearances for Direct Vent .............................................................................................................................................. 9

Heater Installation for Direct Vent .................................................................................................................................. 9

Clearances for Single Flue ............................................................................................................................................ 10

Heater Installation for Single Flue ................................................................................................................................ 10

Speciﬁcations ........................................................................................................................................................ 11 – 14

Clearance to Combustibles ........................................................................................................................................... 15

Rough Framing Dimensions ......................................................................................................................................... 16

Insert Into Masonry Fireplace ....................................................................................................................................... 16

Wall Clearances ............................................................................................................................................................. 17

Log Set Installation Instructions ................................................................................................................................... 18

Vent Examples for Single Flue .............................................................................................................................. 19 - 21

PVVK-CFA Flex Vent Kit ............................................................................................................................................. 22

PVVK-SH Horizontal Vent Adaptor Kit ....................................................................................................................... 23

Horizontal Examples for Colinear Direct Vent ............................................................................................................. 24

Vertical Examples for Colinear Direct Vent ........................................................................................................... 25 - 26

PVCA Horizontal Colinear Direct Vent Adaptor .......................................................................................................... 27

PVVTC Termination Cap Vent Kit ............................................................................................................................... 28

PVCT Colinear Transition Vent Kit .............................................................................................................................. 29

Direct Vent Installation Instructions ...................................................................................................................... 30 - 31

PVVK-24H and PVVK-48H Vent Kit ................................................................................................................... 32 - 33

Gas Connection Installation Instructions ...................................................................................................................... 34

Operating Instructions Checklist ................................................................................................................................... 35

Lighting Instructions .............................................................................................................................................. 36 - 37

Fan Operation ................................................................................................................................................................ 38

Gas Conversion Instructions .................................................................................................................................. 39 - 40

Automatic Humidiﬁer Operation .................................................................................................................................. 41

Optional Controllers ................................................................................................................................................ 42 - 43

Wiring ........................................................................................................................................................................... 44

General Information ...................................................................................................................................................... 45

Maintenance ........................................................................................................................................................... 45 - 46

Unit Operating Faults .................................................................................................................................................... 47

Resetting the Heater ...................................................................................................................................................... 47

Log Placement .............................................................................................................................................................. 47

Main Convection Fan .................................................................................................................................................... 48

Heat Exchanger ............................................................................................................................................................. 48

Surround Installation Instructions ................................................................................................................................. 48

Pedestal Installation Instructions .................................................................................................................................. 49

Parts List ................................................................................................................................................................ 50 - 51

Parts View .............................................................................................................................................................. 52 - 53

Warranty Terms ............................................................................................................................................................. 54

How To Order Repair Parts ........................................................................................................................................... 55

Service Notes ......................................................................................................................................................... 55 - 56

SECTION PAGE

22618-17-0308 Page 3

IMPORTANT SAFETY INFORMATION

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

• Due to high temperatures the appliance should be lo-

cated out of trafﬁc and away from furniture and draper-

ies.

• Children and adults should be alerted to the hazards

of high surface temperatures and should stay away to

avoid burns or clothing ignition.

• Young children should be carefully supervised when

they are in the same room as the appliance.

• Clothing or other ﬂammable material should not be

placed on or near the appliance.

• Any safety screen or guard removed for servicing an ap-

pliance must be replaced prior to operating the appli-

ance.

• Keep burner and control compartment clean.

• Vent cap hot while furnace is in operation.

• For manufactured home (USA only) or mobile home or

residential installation convertible for use with natu-

ral gas and liqueﬁed petroleum gases when provision

is made for the simple conversion from one gas to the

other.

• Installation and repair should be done by a QUALI-

FIED SERVICE PERSON. The appliance should be in-

spected before use and at least annually by a qualiﬁed

service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding materials,

etc. It is imperative that control compartments, burners

and circulating air passageways of the appliance be kept

clean.

• DO NOT put anything around the furnace that will ob-

struct the ﬂow of combustion and ventilation air.

• DO keep the appliance area clear and free from combus-

tible material, gasoline and other ﬂammable vapors and

liquids.

• Do examine venting system periodically and replace

damaged parts.

• Do make a periodic visual check of burner. Clean and

replace damaged parts.

• DO NOT use this heater if any part has been under wa-

ter. Immediately call a qualiﬁed service technician to in-

spect the heater and to replace any part of the control

system and any gas control which has been under wa-

ter.

22618-17-0308Page 4

SAFETY INFORMATION FOR USERS OF LP-GAS

Propane (LP-Gas) is a ﬂammable gas which can cause ﬁres and

explosions. In its natural state, propane is odorless and colorless.

You may not know all the following safety precautions which can

protect both you and your family from an accident. Read them

carefully now, then review them point by point with the mem-

bers of your household. Someday, there may not be a minute to

lose, everyone’s safety will depend on knowing exactly what to

do. If, after reading the following information, you feel you still

need more information, please contact your gas supplier.

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.

That’s your signal to go into immediate action!

• Do not operate electric switches, light matches, use your

phone. Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• LP-Gas is heavier than air and may settle in low areas such

as basements. When you have reason to suspect a gas leak,

keep out of basements and other low areas. Stay out until

ﬁreﬁghters declare them to be safe.

• Use your neighbor’s phone and call a trained LP-Gas ser-

vice person and the ﬁre department. Even though you may

not continue to smell gas, do not turn on the gas again. Do

not re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and ﬁreﬁghters check for es-

caped gas. Have them air out the area before you return.

Properly trained LP-Gas service people should repair the

leak, then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the

odor of the chemical put into the gas. You must ﬁnd out if you

can smell the odorant in propane. Smoking can decrease your

ability to smell. Being around an odor for a time can affect your

sensitivity or ability to detect that odor. Sometimes other odors

in the area mask the gas odor. People may not smell the gas odor

or their minds are on something else. Thinking about smelling a

gas odor can make it easier to smell.

The odorant in LP-gas is colorless, and it can fade under some

circumstances. For example, if there is an underground leak, the

movement of the gas through soil can ﬁlter the odorant. Odorants

in LP-Gas also are subject to oxidation. This fading can occur if

there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That

will take some of the odorant out of the gas, reducing its odor

intensity.

LP-Gas may stratify in a closed area, and the odor intensity could

vary at different levels. Since it is heavier than air, there may be

more odor at lower levels. Always be sensitive to the slightest

gas odor. If you detect any odor, treat it as a serious leak. Imme-

diately go into action as instructed earlier.

SOME POINTS TO REMEMBER

• Learn to recognize the odor of LP-gas. Your local LP-Gas

Dealer can give you a “Scratch and Sniff” pamphlet. Use it

to ﬁnd out what the propane odor smells like. If you suspect

that your LP-Gas has a weak or abnormal odor, call your

LP-Gas Dealer.

• If you are not qualiﬁed, do not light pilot lights, perform ser-

vice, or make adjustments to appliances on the LP-Gas sys-

tem. If you are qualiﬁed, consciously think about the odor of

LP-Gas prior to and while lighting pilot lights or performing

service or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the LP-Gas odor. Do not try to light

pilot lights, perform service, or make adjustments in an area

where the conditions are such that you may not detect the

odor if there has been a leak of LP-Gas.

• Odor fade, due to oxidation by rust or adsorption on walls

of new cylinders and tanks, is possible. Therefore, people

should be particularly alert and careful when new tanks or

cylinders are placed in service. Odor fade can occur in new

tanks, or reinstalled old tanks, if they are ﬁlled and allowed

to set too long before reﬁlling. Cylinders and tanks which

have been out of service for a time may develop internal

rust which will cause odor fade. If such conditions are sus-

pected to exist, a periodic sniff test of the gas is advisable. If

you have any question about the gas odor, call your LP-gas

dealer. A periodic sniff test of the LP-gas is a good safety

measure under any condition.

• If, at any time, you do not smell the LP-Gas odorant and

you think you should, assume you have a leak. Then take

the same immediate action recommended above for the oc-

casion when you do detect the odorized LP-Gas.

• If you experience a complete “gas out,” (the container is un-

der no vapor pressure), turn the tank valve off immediately.

If the container valve is left on, the container may draw in

some air through openings such as pilot light oriﬁces. If this

occurs, some new internal rusting could occur. If the valve is

left open, then treat the container as a new tank. Always be

sure your container is under vapor pressure by turning it off

at the container before it goes completely empty or having it

reﬁlled before it is completely empty.

22618-17-0308 Page 5

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment installed

in every dwelling, building or structure used in whole or in part

for residential purposes, including those owned or operated by the

Commonwealth and where the side wall exhaust vent termination

is less than seven (7) feet above ﬁnished grade in the area of

the venting, including but not limited to decks and porches, the

following requirements shall be satisﬁed:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS.

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gas ﬁtter shall

observe that a hard wired carbon monoxide detector with an

alarm and battery back-up is installed on the ﬂoor level where

the gas equipment is to be installed. In addition, the installing

plumber or gas ﬁtter shall observe that a battery operated

or hard wired carbon monoxide detector with an alarm is

installed on each additional level of the dwelling, building or

structure served by the side wall horizontal vented gas fueled

equipment. It shall be the responsibility of the property owner

to secure the services of qualiﬁed licensed professionals for

the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an attic,

the hard wired carbon monoxide detector with alarm and

battery back-up may be installed on the next adjacent

ﬂoor level.

b. In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the

owner shall have a period of thirty (30) days to comply

with the above requirements; provided, however, that

during said thirty (30) day period, a battery operated

carbon monoxide detector with an alarm shall be

installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each

carbon monoxide detector as required in accordance with the

above provisions shall comply with NFPA 720 and be ANSI/

UL 2034 listed and IAS certiﬁed.

3. SIGNAGE. A metal or plastic identiﬁcation plate shall be

permanently mounted to the exterior of the building at a

minimum height of eight (8) feet above grade directly in line

with the exhaust vent terminal for the horizontally vented gas

fueled heating appliance or equipment. The sign shall read,

in print size no less than one-half (1/2) inch in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side

wall horizontally vented gas fueled equipment shall not

approve the installation unless, upon inspection, the inspector

observes carbon monoxide detectors and signage installed

in accordance with the provisions of 248 CMR 5.08(2)(a) 1

through 4.

(b) EXEMPTIONS: The following equipment is exempt

from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the

most current edition of NFPA 54 as adopted by the

Board; and

2. Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure

separate from the dwelling, building or structure

used in whole or in part for residential purposes.

(d) MANUFACTURER REQUIREMENTS - GAS

EQUIPMENT VENTING SYSTEM NOT PROVIDED.

When the manufacturer of a Product Approved side

wall horizontally vented gas fueled equipment does not

provide the parts for venting the ﬂue gases, but identiﬁes

“special venting systems”, the following requirements

shall be satisﬁed by the manufacturer:

1. The referenced “special venting system” instructions

shall be included with the appliance or equipment

installation instructions; and

2. The “special venting systems” shall be Product

Approved by the Board, and the instructions for

that system shall include a parts list and detailed

installation instruction.

(e) A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists for

venting instructions, and/or all venting design instructions

shall remain with the appliance or equipment at the

completion of the installation.

22618-17-0308Page 6

Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/

CGA-B149 (.1 or .2) installation code.

Recommended Gas Pipe Diameter

Pipe Length Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Nat. L.P. Nat. L.P.

0-10 feet

0-3 meters

1/2”

12.7mm

3/8”

9.5 mm

1/2”

12.7mm

3/8”

9.5 mm

10-40 feet

4-12 meters

1/2”

12.7mm

1/2”

12.7mm

5/8”

15.9 mm

1/2”

12.7mm

40-100 feet

13-30 meters

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

1/2”

12.7mm

100-150 feet

31-46 meters

3/4”

19mm

1/2”

12.7mm

7/8”

22.2 mm

3/4”

19mm

Note: Never use plastic pipe. Check to conﬁrm whether your local

codes allow copper tubing or galvanized.

Note: Since some municipalities have additional local codes, it is

always best to consult your local authority and installation code.

The use of the following gas connectors is recommended:

— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction. The state of Massachusetts requires that a ﬂexible

appliance connector cannot exceed three feet in length.

Figure 1

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.

A manual main gas cock should be located in the vicinity of the

unit. Where none exists, or where its size or location is not ad-

equate, contact your local authorized installer for installation or

relocation.

Compounds used on threaded joints of gas piping shall be resistant

to the action of liqueﬁed petroleum gases. The gas lines must be

checked for leaks by the installer. This should be done with a soap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.

Never use an exposed ﬂame to check for leaks. Appliance must

be disconnected from piping at inlet of control valve and pipe

capped or plugged for pressure test. Never pressure test with

appliance connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required

by the National Fuel Gas Code that a drip line be installed near

the gas inlet. This should consist of a vertical length of pipe tee

connected into the gas line that is capped on the bottom in which

condensation and foreign particles may collect.

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8" (3 mm) N.P.T.

plugged tapping, accessible for test gauge connection, must be

placed immediately upstream of the gas supply connection to

the appliance.

2. The appliance and its individual shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2

psig (3.5 kPa).

3. The appliance must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig (3.5 kPa).

Attention! If one of the procedures results in pressures in excess

of 1/2 psig (14" w.c.) (3.5 kPa) on the ﬁreplace gas valve, it will

result in a hazardous condition.

Checking Manifold Pressure

Both Propane and Natural gas valves have a built-in pressure

regulator in the gas valve. Natural gas models will have a manifold

pressure of approximately 3.5" w.c. (.872 kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 5.0" w.c.

(1.245 kPa) for the purpose of input adjustment to a maximum of

10.5" w.c. (2.614 kPa) Propane gas models will have a manifold

pressure approximately 7.0" w.c. (2.49 kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 11.0" w.c.

(2.739 kPa) for the purpose of input adjustment to a maximum of

13.0" w.c. (3.237 kPa).

A 1/8" (3 mm) N.P.T. plugged tapping, accessible for test gauge

connection, is located on the outlet side of the gas control.

GAS SUPPLY

FLEX TUBING

3/8 NPT

NIPPLE

FLARE FITTING

GAS VALVE

SOLENOID FLARE SHUT OFF VALVE

22618-17-0308 Page 7

Qualiﬁed Installing Agency

Installation and replacement of gas piping, gas utilization equip-

ment or accessories and repair and servicing of equipment shall be

performed only by a qualiﬁed agency. The term “qualiﬁed agen-

cy” mean any individual, ﬁrm, corporation or company which

either in person or through a representative is engaged in and is

responsible for (a) the installation or replacement of gas piping or

(b) the connection, installation, repair or servicing of equipment,

who is experienced in such work, familiar with all precautions re-

quired and has complied with all the requirements of the authority

having jurisdiction.

The installation must conform with local codes, or in the absence

of local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA

54 or Natural Gas and Propane Installation Code, CSA B149.1.

* Available from the American National Standards Institute, Inc.,

11 West 42nd St., New York, NY 10036.

A manufactured home (USA only) or mobile home OEM instal-

lation must conform with the Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home

Installations, ANSIZ225.1, or Standard for Gas Equipped Recre-

ational Vehicles and Mobile Housing, CSA Z240.0.

High Altitudes

For altitudes/elevations above 2,000 feet (610 m), input ratings

should be reduced at the rate of 4 percent for each 1,000 feet (305

m) above sea level, this may be accomplished by reducing mani-

fold pressure. The maximum allowable reduction in manifold

pressure for Natural gas shall be from 3.5” w.c. (.872 kPa) to 2.8”

w.c. (.697 kPa). The maximum allowable reduction in manifold

pressure for Propane (LP) gas shall be from 10.0” w.c. (2.49 kPa)

to 8.0” w.c. (1.99 kPa). For Canadian high altitude applications,

this appliance is suitable for installation at elevations between 0

feet (0 m) and 4,500 feet (1,372 m) without change.

Canada:

This appliance is NOT to be installed in Canada.

Introduction

Always consult your local Building Department regarding regu-

lations, codes or ordinances which apply to the installation of a

direct vent wall furnace.

Instructions to Installer

1. Installer must leave instruction manual with owner after in-

stallation.

2. Installer must have owner ﬁll out and mail warranty card sup-

plied with furnace.

3. Installer should show owner how to start and operate furnace

and thermostat.

4. Installer must locate unit near a grounded wall receptacle for

115VAC power and must provide gas supply and vent the

unit properly for safe operation.

General Information

This series is designed certiﬁed in accordance with American

National Standard/CSA Standard Z21.88 and CSA 2.33 by the

Canadian Standards Association as a Gas Fireplace Heater to be

installed according to these instructions.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not shown

on the rating plate is the responsibility of the person and com-

pany making the change.

Important

All Correspondence should refer to complete Model Number, Se-

rial Number and type of gas.

Notice: During initial ﬁring of this unit, oil from the heat exchang-

er may bake out and smoke may occur. To prevent triggering of

smoke alarms, ventilate the room in which the unit is installed.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed

so that all burners and burner ignition devices are located not less

than 18” (457 mm) above the ﬂoor.

Such equipment shall be located, or protected, so it is not subject

to physical damage by a moving vehicle.

Warning:

Any change to this furnace or its control can be dangerous.

This is a heating appliance and any panel, door or guard

removed for servicing an appliance must be replaced prior

to operating the appliance.

Sate of Massachusetts: The installation must be made by a

licensed plumber or gas ﬁtter in the Commonwealth of Mas-

sachusetts.

INTRODUCTION

22618-17-0308Page 8

Model PV28SV50

Input BTU/HR (KW/H) 19,000 Rear - 9,000 Front

Height 25 1/8”

Width 28 3/16”

Depth 17 5/8”

Gas Inlet (Pipe) 3/8” Flair

Electrical - Unit has a 5’ (1.5 m) 3 pronged cordset for con-

nection to an approved 115 VAC 60 Hz maximum

AMPs - 5A wall receptacle.

Accessories

Part Number Description

PV-2H Top Cover - Slim Assembly

PV-4H Top Cover - Short Assembly

PVPK Pedestal Kit

PVE-1 6” Surround Assembly

PVSH Rear Shroud

TRW Wall Thermostat - Wireless Remote

FRBTC Battery Operated Remote w/Thermostat

FRBTP Battery Operated Remote w/Programmable Ther-

mostat

TMV2 Two-Stage Thermostats

CIPFP-1 Floor Pad Kit

CIFPB-1C Corner Floor Pad Kit

PVVK24H Direct Vent 24” Vent Kit

PVVK48H Direct Vent 48” Vent Kit

PVVK-SH Single Flue Horizontal Vent Kit

PVVK-SV Single Flue Vertical Vent Kit

PVVK-CFA Flex Vent Kit

PVCT Colinear Transition

PVVTC Vertical Termination Cap - 1.5”

PVCA Colinear Adapter

SPECIFICATIONS

INSTALLATION INSTRUCTIONS - GENERAL SAFETY INFORMATION

1. This installation must conform with local codes or, in the ab-

sence of local codes with NFPA54.

2. Provide adequate clearances around the product for servic-

ing and ensure there are no obstructions to the combustion

air intake situated at the back of the heater. Refer to Page 15,

Figures 7 through 10.

3. The appliance must be installed on a ﬂat, solid continuous

surface (i.e. wood, metal, concrete). Please Note: Rough or

uneven surfaces can cause vibration or humming in the heat-

er.

4. The Mantis Power-Vent High-Effeciency Fireplace can be in-

stalled in a wide variety of ways and will ﬁt nearly any room

layout. It may be installed in a recessed position, framed out

into the room, or across a corner. For installation options re-

fer to page 15.

5. This appliance (Insert and Freestanding Models) needs to be

installed in such a way that the heater can be removed at all

times to service the heater exchanger and ﬂue fan located in

the rear section of the heater.

Note: Under no circumstances should the appliance be in-

stalled under conditions which would not allow for

easy removal of the appliance to carry out routine

inspection and service to the appliance, to do so will

void the warranty.

Note: On Single Wall ﬂue pipe installations (imitation zero

clearance ﬁreplace) a minimum of 2” (50.8 cm) clear-

ance must be provided at the rear of the heater to enable

the heater to get sufﬁcient combustion air to the air inlet

located at the rear of heater. Refer to installation instruc-

tions on page 15, Figures 7 through 10.

Note: Where a mantel surround is being used on insert installa-

tions and zero clearance ﬁreplace installations, the com-

bustion air intake slot located in the top mantel surround

must have no obstructions to allow combustion air to en-

ter through the slot to the combustion air inlet located at

the back of the heater.

22618-17-0308 Page 9

1. Pick a location on a wall with a clear space in the room. In

selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper

installation. Be sure to locate the unit close enough to a 110

VAC wall receptacle to properly power appliance.

2. When facing the front of the furnace the minimum clearances

from casing to combustible construction are 0” (0 mm) on top,

0” (0 mm) on each side, recommend 4” (102 mm) on sides

for servicing and 0” (0 mm) from the ﬂoor, 0” (0 mm) to rear

wall and 40” (1,016 mm) from Mantis top to ceiling.

3. The minimum distance from the center of the vent cap to the

nearest outside corner or obstruction is 12” (305 mm).

4. The minimum wall depth is 4” (102 mm) and the maximum

is 48” (121.92 cm).

The vent terminal of a direct vent appliance, with an input of

50,000 BTU (14.6KW) per hour or less shall be located at least

9” (229 mm) from any opening through which ﬂue gases could

enter a building.

The bottom of the exhaust vent terminal and the air intake shall

be located at least 12” (305 mm) above grade and must be vented

outside.

WARNING: The nearest point of the vent cap should be

a minimum horizontal distant of six (6) feet (1.83 m) from

any pressure regulator. In case of regulator malfunction,

the six (6) feet (1.83 m) distance will reduce the chance of

gas entering the vent cap.

Installation on Rugs and Tile

If this appliance is to be installed directly on carpeting, tile, or other

combustible material, other than wood ﬂooring, the appliance shall

be installed on a metal or wood panel extending the full width and

depth of the appliance.

The base referred to above does not mean the ﬁre-proof base as

used on wood stoves. The protection is primarily for rugs that may

be extremely thick and light-color tile that can discolor.

Locating Wall Opening

The recommended location for this furnace is on an outside wall.

Locate wall studs so that wall vent opening will be located between

wall studs. The wall opening required for venting is a 3 1/2” (89

mm) minimum diameter opening.

Refer to Figures 3 and 6 for positioning the heater on wall and for

locating gas line connection and vent opening. Furnace can sit on

the ﬂoor.

CLEARANCES FOR DIRECT VENT

HEATER INSTALLATION FOR DIRECT VENT

1 9/16”

4 3/32”

Figure 2

22618-17-0308Page 10

1. Pick a location on a wall with a clear space in the room. In

selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper

installation. Be sure to locate the unit close enough to a 115

VAC wall receptacle to properly power appliance.

2. When facing the front of the furnace, the minimum clearances

from casing to combustible construction are 0” (0 mm) on top,

0” (0 mm) on each side, recommend 4” (102 mm) for servicing

and 0” (0 mm) from the ﬂoor and 2” (51 mm) to rear wall for

servicing and installation.

3. The minimum distance from the center of the vent cap to the

nearest outside corner or obstruction is 12” (305 mm).

The bottom of the exhaust vent terminal and the air intake shall

be located at least 12” (305 mm) above grade and must be vented

outside.

WARNING: The nearest point of the vent cap should be a

minimum horizontal distance of six (6) feet (1.83 m) from

any pressure regulator. In case of regulator malfunction,

the six (6) feet (1.83 m) distance will reduce the chance of

gas entering the vent cap.

Installation on Rugs and Tile

If this appliance is to be installed directly on carpeting, tile, or other

combustible material, other than wood ﬂooring, the appliance shall

be installed on a metal or wood panel extending the full width and

depth of the appliance.

The base referred to above does not mean the ﬁre-proof base as

used on wood stoves. The protection is primarily for rugs that may

be extremely thick and light-color tile that can discolor.

Locating Wall Opening

The recommended location for this heater is on an outside wall (the

unit can be located on an inside wall but must not exceed 40’ (12.19

m) in exhaust vent length). Locate wall studs so that wall vent opening

will be located between wall studs. The wall opening required for

venting is a 1 7/8” (48 mm) minimum diameter opening.

Refer to Figures 3 to 6 for positioning the heater on wall and for

locating gas line connection and vent opening. Heater can sit on

the ﬂoor.

CLEARANCES FOR SINGLE FLUE

HEATER INSTALLATION FOR SINGLE FLUE

This manual suits for next models

Table of contents

Other Empire Comfort Systems Indoor Fireplace manuals

Empire Comfort Systems

Empire Comfort Systems BF28BMN-4 User manual

Empire Comfort Systems

Empire Comfort Systems VF24FP2-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVP36PP32EN-4 User manual

Empire Comfort Systems

Empire Comfort Systems MILLIVOLT DVCD FP3-4 Series User manual

Empire Comfort Systems

Empire Comfort Systems Tahoe DVP36FP30-4NAT Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVCT36CBP95N-1 Planning guide

Empire Comfort Systems

Empire Comfort Systems DVP42FP3(0 Quick start guide

Empire Comfort Systems

Empire Comfort Systems EBL50 User manual

Empire Comfort Systems

Empire Comfort Systems DVP FP3 4 Series Quick start guide

Empire Comfort Systems

Empire Comfort Systems VFP36PP32EP-2 Quick start guide

Empire Comfort Systems

Empire Comfort Systems B3STHK18STN-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems MANTIS BF28(B User manual

Empire Comfort Systems

Empire Comfort Systems VFP24FP30 Quick start guide

Empire Comfort Systems

Empire Comfort Systems Boulevard LS41THF-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems Deluxe VFD32FB0L-3 Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVP20MS Quick start guide

Empire Comfort Systems

Empire Comfort Systems DV25IN33LN-3 Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVD32FP7 User manual

Empire Comfort Systems

Empire Comfort Systems Boulevard LS60THF-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVCP36(PP Quick start guide

Empire Comfort Systems

Empire Comfort Systems EBL34 User manual

Empire Comfort Systems

Empire Comfort Systems AV36MTEKN-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVP48FP30 Quick start guide

Empire Comfort Systems

Empire Comfort Systems DLCX36SP93N-1 Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual