Empire Comfort Systems DVP48FP30 Quick start guide

Page 1

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death or

property damage.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas

supplier, call the re department.

—

Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

NOTE: Barrier required, but may be sold separately.

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and shall

be installed for the protection of children and other at-risk

individuals.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

state or local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certied kit is used.

WARNING

If not installed, operated and maintained in

accordance with the manufacturer’s instruc-

tions, this product could expose you to sub-

stances in fuel or from fuel combustion which

can cause death or serious illness.

DIRECT-VENT ZERO

CLEARANCE GAS FIREPLACE

HEATER MODELS:

MILLIVOLT

STANDING PILOT

DVP(42,48)

FP3(0,1,2,3)(N,P)-4

REMOTE

DVP(42,48)FP9(1,3)

(N,P)-6

INTERMITTENT

PILOT

DVP(42,48)

FP7(0,1,2,3)(N,P)-5

GAS-FIRED

UL FILE NO. MH30033

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

39359-4-0320Page 2

TABLE OF CONTENTS

Important Safety Information.....................................................................................................................................3

Safety Information For Users Of Propane Gas .........................................................................................................4

Requirements For Massachusetts ............................................................................................................................5

Introduction ...............................................................................................................................................................6

Specications ............................................................................................................................................................7

Vent System Identication.........................................................................................................................................8

Special Vent Systems ...............................................................................................................................................9

Fireplace Dimensions................................................................................................................................................9

Clearances ..............................................................................................................................................................10

Locating Fireplace................................................................................................................................................... 11

Gas Supply..............................................................................................................................................................12

Installation ..........................................................................................................................................................13-16

Venting Fireplace - Top.......................................................................................................................................17-19

Examples - Top Vent Run........................................................................................................................................20

Venting Examples When Using SD58DVA-X46 Adaptor.........................................................................................21

Venting Fireplace - Rear .........................................................................................................................................22

Examples - Rear Vent Run......................................................................................................................................23

Rear Vent Conversion .............................................................................................................................................24

Vent Clearances......................................................................................................................................................25

8” Venting Framing And Finishing ......................................................................................................................26-27

6-5/8" Venting Framing And Finishing................................................................................................................28-29

Termination Clearances ..........................................................................................................................................30

Horizontal Termination.............................................................................................................................................31

Vertical Termination ............................................................................................................................................32-33

DVVK-4RE Vent Kit Installation Instructions ......................................................................................................34-36

DVVK-5F Flex Vent Instructions..............................................................................................................................37

Propane Gas Conversion........................................................................................................................................38

Log Identication .....................................................................................................................................................39

Log Placement (4 Log Set) ................................................................................................................................40-45

Millivolt System Operating Instructions ..............................................................................................................46-47

Millivolt System Standing Pilot Wiring Diagram ......................................................................................................48

Millivolt System Standing Pilot Lighting Instructions ...............................................................................................49

Millivolt System Standing Pilot Troubleshooting......................................................................................................50

IPI Electronic System Operating Instructions..........................................................................................................51

IPI Electronic System Wiring Diagram ....................................................................................................................52

Intermittent Pilot Lighting Instructions .....................................................................................................................53

Intermittent Pilot Control System Troubleshooting .............................................................................................54-56

Remote Control Operation Instructions..............................................................................................................57-62

Remote Control Wiring Diagram .............................................................................................................................63

Remote Control - Lighting Instructions....................................................................................................................64

Remote Control System Troubleshooting ..........................................................................................................65-66

Maintenance And Service ..................................................................................................................................67-69

DVP42FP(3,5,7,9) Parts List..............................................................................................................................70-71

DVP48FP(3,5,7,9) Parts List..............................................................................................................................72-73

Parts View ...............................................................................................................................................................74

Master Parts Distributor List....................................................................................................................................75

How To Order Repair Parts .....................................................................................................................................75

FBB4 Optional Variable Speed Blower Installation ............................................................................................76-77

Junction Box Wiring Installation Instructions...........................................................................................................78

Optional Brick Liner Installation Instructions ...........................................................................................................78

Accessories.............................................................................................................................................................79

Quick Reference Guide......................................................................................................................................80-81

Warranty..................................................................................................................................................................82

Fireplace Service History ........................................................................................................................................83

SECTION PAGE

39359-4-0320 Page 3

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

IMPORTANT SAFETY INFORMATION

WARNING

1. “Due to high temperatures, the appliance should be

located out of trafc and away from furniture and

draperies.”

2. “Children and adults should be alerted to the hazards

of high surface temperature and should stay away to

avoid burns or clothing ignition.”

3. “Young children should be carefully supervised when they

are in the same room as the appliance. Toddlers, young

children, and others may be susceptible to accidental

contact burns. A physical barrier is recommended if there

are at-risk individuals in the house. To restrict access to a

replace or stove, install an adjustable safety gate to keep

toddlers, young children, and other at-risk individuals out

of the room and away from hot surfaces.”

4. For appliances requiring a barrier, as determined under

Clause 5.15.4: “A barrier designed to reduce the risk of

burns from the hot viewing glass is provided with this

appliance and shall be installed for the protection of

children and other at-risk individuals.”

5. “If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

”

6. “Clothing or other ammable material should not be

placed on or near the appliance.”

7. “Any safety screen, guard, or barrier removed for

servicing an appliance must be replaced prior to

operating the appliance” (see Clause 4.1.6).

8. “Installation and repair should be done by a qualied

service person. The appliance should be inspected

before use and at least annually by a professional service

person. More frequent cleaning might be required due to

excessive lint from carpeting, bedding material, et cetera.

It is imperative that control compartments, burners, and

circulating air passageways of the appliance be kept

clean.”

9. The instructions for an appliance optionally for use

with glass doors (or equivalent) shall state that, “Only

doors certied with the appliance shall be used.”

10. The instructions for an appliance not intended for use

with glass doors (or equivalent) shall emphasize that

the appliance is not for use with glass doors.

11. Where applicable, provide a means by which the

consumer can identify the barrier, (such as graphic

representation, clear description, or reference marking).

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance

connected to the venting system being placed into operation

could result in carbon monoxide poisoning or death.

The following steps shall be followed for each appliance

connected to the venting system being placed into operation,

while all other appliances connected to the venting system

are not in operation:

1. Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and horizontal

pitch, as required in the National Fuel Gas Code ANSI

Z223.1/NFPA 54 or the National Gas and Propane

Installation Code CSA B149.1 and these instructions.

Determine that there is no blockage or restriction,

leakage, corrosion and other deciencies which could

cause an unsafe condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which

the appliance(s) connected to the venting system are

located and other spaces of the building.

4. Close replace dampers.

5. Turn on clothes dryers and any appliance not connected

to the venting system. Turn on any exhaust fans, such

as range hoods and bathroom exhausts, so they are

operating at maximum speed. Do not operate a summer

exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the thermostat

so appliance is operating continuously.

7. Test for spillage from draft hood equipped appliances

at the draft hood relief opening after 5 minutes of main

burner operation. Use the ame of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected

in accordance with National Fuel Gas Code, ANSI

Z223.1/NFPA and/or National Gas and Propane

Installation Code, CSA B149.1.

9. After it has been determined that each appliance

connected to the venting system properly vents when

tested as outlined above, return doors, windows,

exhaust fans, replace dampers and any other gas-red

burning appliance to their previous conditions of use.

39359-4-0320Page 4

Some people cannot smell well. Some people cannot smell the

odor of the chemical put into the gas. You must nd out if you

can smell the odorant in propane. Smoking can decrease your

ability to smell. Being around an odor for a time can affect your

sensitivity or ability to detect that odor. Sometimes other odors in

the area mask the gas odor. People may not smell the gas odor

or their minds are on something else. Thinking about smelling a

gas odor can make it easier to smell.

The odorant in Propane Gas is colorless, and it can fade under

some circumstances. For example, if there is an underground

leak, the movement of the gas through soil can lter the odorant.

Odorants in Propane Gas also are subject to oxidation. This fading

can occur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

take some of the odorant out of the gas, reducing its odor intensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest

gas odor. If you detect any odor, treat it as a serious leak. Imme-

diately go into action as instructed earlier.

Propane is a ammable gas which can cause res and explo-

sions. In its natural state, propane is odorless and colorless.

You may not know all the following safety precautions which

can protect both you and your family from an accident. Read

them carefully now, then review them point by point with the

members of your household. Someday when there may not

be a minute to lose, everyone’s safety will depend on knowing

exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

• Learn to recognize the odor of Propane Gas.Your local Propane

Gas Dealer can give you a “Scratch and Sniff” pamphlet. Use

it to nd out what the propane odor smells like. If you suspect

that your Propane Gas has a weak or abnormal odor, call your

Propane Gas Dealer.

• If you are not qualied, do not light pilot lights, perform service,

or make adjustments to appliances on the Propane Gas system.

If you are qualied, consciously think about the odor of Propane

Gas prior to and while lighting pilot lights or performing service

or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the Propane Gas odor. Do not try to

light pilot lights, perform service, or make adjustments in an

area where the conditions are such that you may not detect

the odor if there has been a leak of Propane Gas.

• Odor fade, due to oxidation by rust or adsorption on walls of

new cylinders and tanks, is possible. Therefore, people should

be particularly alert and careful when new tanks or cylinders

are placed in service. Odor fade can occur in new tanks, or

reinstalled old tanks, if they are lled and allowed to set too

long before relling. Cylinders and tanks which have been out

of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question

about the gas odor, call your Propane Gas Dealer. A peri-

odic sniff test of the Propane Gas is a good safety measure

under any condition.

• If, at any time, you do not smell the Propane Gas odorant and

you think you should, assume you have a leak. Then take the

same immediate action recommended above for the occasion

when you do detect the odorized Propane Gas.

• If you experience a complete “gas out,” (the container is under

no vapor pressure), turn the tank valve off immediately. If the

container valve is left on, the container may draw in some air

through openings such as pilot light orices. If this occurs, some

new internal rusting could occur. If the valve is left open, then

treat the container as a new tank. Always be sure your con-

tainer is under vapor pressure by turning it off at the container

before it goes completely empty or having it relled before it is

completely empty.

• Do not operate electric switches, light matches, use your phone.

Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• Propane Gas is heavier than air and may settle in low areas

such as basements. When you have reason to suspect a gas

leak, keep out of basements and other low areas. Stay out until

reghters declare them to be safe.

• Use your neighbor’s phone and call a trained Propane Gas

service person and the re department. Even though you may

not continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and reghters check for escaped

gas. Have them air out the area before you return. Properly

trained Propane Gas service people should repair the leak,

then check and relight the gas appliance for you.

SOME POINTS TO REMEMBER

NO ODOR DETECTED - ODOR FADE

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the Propane Gas.

That’s your signal to go into immediate action!

SAFETY INFORMATION FOR USERS OF PROPANE GAS

39359-4-0320 Page 5

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in whole

or in part for residential purposes, including those owned or

operated by the Commonwealth and where the side wall exhaust

vent termination is less than seven feet above nished grade in

the area of the venting, including but not limited to decks and

porches, the following requirements shall be satised:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS.

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gastter

shall observe that a hard wired carbon monoxide detector

with an alarm and battery back-up is installed on the oor

level where the gas equipment is to be installed. In addition,

the installing plumber or gastter shall observe that a battery

operated or hard wired carbon monoxide detector with an

alarm is installed on each additional level of the dwelling,

building or structure served by the side wall horizontal

vented gas fueled equipment. It shall be the responsibility

of the property owner to secure the services of qualied

licensed professionals for the installation of hard wired

carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an

attic, the hard wired carbon monoxide detector with

alarm and battery back-up may be installed on the next

adjacent oor level.

b. In the event that the requirements of this subdivision

can not be met at the time of completion of installation,

the owner shall have a period of thirty days to comply

with the above requirements; provided, however, that

during said thirty day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each

carbon monoxide detector as required in accordance with

the above provisions shall comply with NFPA 720 and be

ANSI/UL 2034 listed and IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be

permanently mounted to the exterior of the building at a

minimum height of eight feet above grade directly in line with

the exhaust vent terminal for the horizontally vented gas fueled

heating appliance or equipment. The sign shall read, in print

size no less than 1/2 inch in size, “GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side

wall horizontally vented gas fueled equipment shall not

approve the installation unless, upon inspection, the inspector

observes carbon monoxide detectors and signage installed

in accordance with the provisions of 248 CMR 5.08(2)(a) 1

through 4.

(b) EXEMPTIONS: The following equipment is exempt from

248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the most

current edition of NFPA 54 as adopted by the Board;

and

2. Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure

separate from the dwelling, building or structure

used in whole or in part for residential purposes.

(d) MANUFACTURER REQUIREMENTS - GAS

EQUIPMENT VENTING SYSTEM NOT PROVIDED.

When the manufacturer of a Product Approved side

wall horizontally vented gas fueled equipment does not

provide the parts for venting the ue gases, but identies

“special venting systems”, the following requirements

shall be satised by the manufacturer:

1. The referenced “special venting system” instructions

shall be included with the appliance or equipment

installation instructions; and

2. The “special venting systems” shall be Product

Approved by the Board, and the instructions for

that system shall include a parts list and detailed

installation instruction.

(e) A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists for

venting instructions, and/or all venting design instructions

shall remain with the appliance or equipment at the

completion of the installation.

39359-4-0320Page 6

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner ll out and mail warranty card supplied

with the replace.

3. Installer should show owner how to start and operate the replace.

This direct vent gas replace heater is designed to operate with

all combustion air being siphoned from the outside of the building

and all exhaust gases expelled to the outside of the building. The

information contained in this manual pertains to all models and gas

control systems unless otherwise noted.

WARNING

This unit is not for use with solid fuels.

Appliance Certication

This replace is design certied in accordance with American

National Standard/CSA Standard ANSI Z21.88/CSA 2.33 and by

Underwriters Laboratories as a Direct Vent Gas Fireplace Heater

and shall be installed according to these instructions.

Consult your local building code agency, prior to installation, to ensure

compliance with local codes-including permits and inspections.

The replace, when installed, must be electrically grounded in

accordance with local codes or, in absence of local codes, with the

National Electric Code ANSI/NFPA 70 or Canadian Electric code,

CSA C22.1, if an external electrical source is utilized.

These models may be installed in a bedroom or bed-sitting room

in the U.S.A. and Canada.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performed only by a qualied agency. The term “qualied agency”

means any individual, rm, corporation or company which either in

person or through a representative is engaged in and is responsible for

(a) the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

such work, familiar with all precautions required and has complied

with all the requirements of the authority having jurisdiction.

Commonwealth of Massachusetts: The installation must be

made by a licensed plumber or gas tter in the Commonwealth

of Massachusetts.

The installation must conform with local codes or, in the absence of

local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA

54* Natural Gas and Propane Installation Code, or CSA B149.1 in

Canada. *Available from the American National Standards Institute,

Inc. 11 West 42nd St., New York, N.Y. 10036.

WARNING

ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS

CAN BE DANGEROUS.

Improper installation or use of the replace can cause

serious injury or death from re, burns, explosions, or

carbon monoxide poisoning.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not

shown on the rating plate is the responsibility of the person

and company making the change.

Important

All correspondence should refer to complete Model Number, Serial

Number and type of gas.

High Altitude

When installing this unit at an elevation above 2000 feet (in the

United States) it may be necessary to decrease the input rating by

changing the existing burner orice to a smaller size. Generally,

input should be reduced 4 percent for each 1000 feet above sea

level. However, if the heating value of the gas has been reduced,

this general rule may not apply. Check with local gas utility for proper

orice size identication.

Canadian High Altitude

Altitude: 0-4500 feet (0-1370 m)

When installing this unit at an elevation above 4500 feet (in Canada),

check with local authorities.

Consult your local gas utility for assistance in determining the proper

orice for location.

Preparation

This direct vent gas replace and its components are tested and

safe when installed in accordance with this Installation Manual.

Report to your dealer any parts damaged in shipment, specically

check glass condition. Do not install unit with damaged, incomplete,

or substitute parts. Read all instructions before starting installation

and follow these instructions carefully during installation to insure

maximum benet and safety. Failure to follow them will void your

warranty and may present a re hazard.

The warranty will be voided by, and the warranter disclaims any

responsibility for the following actions:

• Installation of any damaged replace or vent system component.

• Modication of the replace or direct vent system.

• Installation other than as instructed by Empire Comfort Systems,

Inc.

• Improper positioning of the logs, glass door or decorative rock.

• Installation and/or use of any component part not manufactured

or approved by manufacturer.

INTRODUCTION

39359-4-0320 Page 7

Remote Control Options And Accessories Description

FRBC Millivolt/IP Battery Remote ON/OFF

FRBTC Millivolt/IP Battery Remote T-Stat

TMW Millivolt/IP WIRELESS Wall Thermostat

TRW Millivolt/IP REED SWITCH Wall Thermostat

FWS-1 Millivolt/IP Wall Switch

FREC Electric Remote

FBB4 Blower Assembly

DVP42 DVP48

Input Btu/hr Maximum 28,000 (Natural)

28,000 (Propane)

30,000 (Natural)

30,000 (Propane)

Btu/hr Minimum (millivolt only) 19,000 (Natural)

22,000 (Propane)

20,500 (Natural)

24,000 (Propane)

KWH (Maximum) 8.2 8.8

(Minimum) 5.5 6.0

NATURAL

Orice #38 (.1015) P-203 - (DVP42FP(3,7,9)) #37 (.1040) P-213 - (DVP48FP(3,7,9))

Air Shutter Opening 1/8"(3.2mm) 1/8"(3.2mm)

PROPANE

Orice #52 (.0635") P-185 1.65MM P-250

Air Shutter Opening FULL OPEN FULL OPEN

Height without standoff 34 3/4"(883mm) 34 3/4"(883mm)

Width 43"(1092mm) 49"(1245mm)

Depth 19 7/8"(505mm) 19 7/8"(505mm)

Gas Inlet Shutoff Valve (Pipe) 1/2 NPT 1/2 NPT

NOTICE: Air shutter settings are factory minimum settings. Some venting congurations may require minor air shutter adjustments for

optimum performance.

SPECIFICATIONS

FIREPLACE BARRIER SCREENS

Model Description Used On

DVFB42TBL Fireplace Barrier Screen, Matte Black DVP42FP

DVFB48TBL Fireplace Barrier Screen, Matte Black DVP48FP

NOTICE: A rescreen is required for operation of the appliance, but are sold separately. Follow the instructions that come with your re-

screen for proper installation.

CONVERSION KITS

Models Description Part Numbers

DVP42FP3(0,1) Propane to Natural 18824

DVP42FP3(0,1) Natural to Propane 18821

DVP42FP7(0,1) Propane to Natural 32016

DVP42FP7(0,1) Natural to Propane 32021

DVP42FP91 Propane to Natural 35462

DVP42FP91 Natural to Propane 35463

DVP48FP3(0,1) Propane to Natural 18825

DVP48FP3(0,1) Natural to Propane 18822

DVP48FP7(0,1) Propane to Natural 32017

DVP48FP7(0,1) Natural to Propane 32022

DVP48FP91 Propane to Natural 35464

DVP48FP91 Natural to Propane 35445

39359-4-0320Page 8

VENT SYSTEM IDENTIFICATION

Figure 1

Begin the vent system installation by selecting the type of venting

to be installed and the path that it will take. Verify that clearances

are met throughout the path of the venting system. Determine if the

replace is to be vented out the top or out the rear.

NOTICE: Some replaces cannot be vented out the rear of the

replace.

Determine how the vent system will be terminated out the side of

the house or through the roof. Verify clearances for the termination.

When selecting a vent system for use with the replace, refer to

the “Special Vent Systems” section in this manual to determine

what systems are acceptable. Check all clearances and venting

components. Identify if any problems existing in the vent system.

Use Figure 22 on page 17 for top venting, or Figure 35 on page

22 for rear venting to eliminate issues after installation. Check pipe

diameter on vent system and replace to verify the size is the same.

NOTICE: All outer connection joints must be sealed with

aluminum tape, screws or silicone sealant rated above

300°F/149°C. The inner ue joints do not require any sealant.

SPECIAL VENTING COMPONENTS (DURAVENT)

See Empire Comfort Systems Retail Price List for Duravent

part numbers and pricing.

Special DV Vent Kits Available from Empire Comfort Systems,

Inc. dealers.

DVVK-4VP

Direct-Vent Fireplace Vent Kit - Vertical, Includes

SD46DVA-VCH, SD46DVA-F6 and SD46DVA-SC

DVVK-4RE Direct-Vent Fireplace Vent Kit, Thru-the-wall, for

5 to 13-3/4 inch wall thickness

DVVK-4TP

Direct-Vent Fireplace Vent Kit for Top Vent, Thru-

the-wall, 8 to 11 inch wall thickness, Includes

SD46DVA-HC, SD46DVA-E90,

SD46DVA-09, SD46DVA-08A and SD46DVAWT

DVVK-4TSP

Direct-Vent Fireplace Vent Kit for Top Vent, Thru-

the-wall, 5 to 7 inch wall thickness, Includes

SD46DVA-HC, SD46DVA-E90,

SD46DVA-06 and SD46DVA-WT

DVVK-5RP

Direct-Vent Fireplace Vent Kit for Rear Vent, 6 to

12 inch wall thickness, Includes SD-58DVA06,

SD-58DVAHC, and SD58DVAWTEC

DVVK-5TP

Direct-Vent Fireplace Vent Kit for Top Vent, Thru-

the-wall, 4 to 6 inch wall thickness, Includes

SD58DVAE90, SD58DVAHC,

SD58DVA06, and SD58DVAWTEC

DVVK-5VP Direct Vent Fireplace Vent Kit - Vertical, Includes

SD58DVAVCH, SD58DVASC, and SD58DVAF6

*DVVK-5F Horizontal Flex Vent Kit (4’ Flex) (1.22m)

*DVVK-4F Direct-Vent Fireplace Horizontal Flex Vent Kit

*Empire Flex Vent Kits

NOTE: Appliances can use the DVVK-4 Hard Pipe Vent Systems,

only if using a SD58DVA-X46 adaptor.

*NOTE: If using three

90° elbows during

horizontal termination.

See Figure 30.

39359-4-0320 Page 9

The following vent systems are acceptable for use with the

DVP (42,48) series replaces:

• Duravent® Pro 5" - 8"

• American Metal Products 5" - 8"

• Selkirk Direct-Temp® 5" - 8"

• Security Secure Vent® 5" - 8"

• Excel DV Venting 5” - 8”

• BDM 5” - 8”

• MetalFab SureSeal® 5” - 8”

• Olympia VENTIS®

• Empire Flexvent Kit DVVK-5F

The following vent systems are acceptable for use with the

adaptor vertically off top of replace only:

• Duravent® Pro 4" - 6 5/8"

• American Metal Products 4" - 6 5/8"

• Selkirk Direct-Temp ® 4" - 6 5/8"

• Security Secure Vent ® 4" - 6 5/8"

• Excel DV Venting 4" - 6 5/8"

• BDM 4" - 6 5/8"

• MetalFab SureSeal® 4" - 6 5/8"

• Empire Horizontal Round Termination Kits DVVK-4RE, DVVK-4REVS

NOTE: SD58DVA-X46 Not for use with Flex Vent Kits. For use

with Duravent® Pro 4"- 6⅝" Hard Pipe venting only.

Figure 2

FIREPLACE DIMENSIONS

A B C D E F G H I J K

DVP42 43”

(1092mm)

40”

(1016mm)

25 1/16”

(636 mm)

37 5/8”

(956 mm)

34 3/4”

(883 mm)

19 7/8”

(505 mm)

26”

(660 mm)

7 1/8”

(181 mm)

26 1/2”

(826 mm)

13 1/4”

(337 mm)

12 3/4”

(324 mm)

DVP48 49”

(1245mm)

46”

(1168mm)

25 1/16”

(636 mm)

37 5/8”

(956 mm)

34 3/4”

(883 mm)

19 7/8”

(505 mm)

26”

(660 mm)

7 1/8”

(181 mm)

32 1/2”

(826 mm)

16 1/4”

(413 mm)

12 3/4”

(324 mm)

SPECIAL VENT SYSTEMS

39359-4-0320Page 10

CLEARANCES

CLEARANCE TO COMBUSTIBLES

Back 0" (0 mm)

Side 0" (0 mm)

Floor 0" (0 mm)

Top Stand-off 0" (0 mm)

Top Framing Edge 3" (76 mm)

NOTE A: See Figure 5 for maximum mantel depth.

NOTE B: See Figure 5 for minimum height above unit.

Figure 3

Combustible Material

No greeting cards, stockings or ornamentation of any type should

be placed on or attached to the replace. The ow of heat can

ignite combustibles.

Figure 4

Mantel Chart

Figure 5

Clearances

Clearance from top front edge of replace to ceiling is 36”

Clearance from side of replace to adjacent sidewall is 6”.

See Figure 6.

(914mm)

Figure 6

This manual suits for next models

Table of contents

Other Empire Comfort Systems Indoor Fireplace manuals

Empire Comfort Systems

Empire Comfort Systems Tahoe DVP36PP32EN-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems Boulevard MULTIFUNCTION REMOTE DVLL60BP90N-2 User manual

Empire Comfort Systems

Empire Comfort Systems DLCX36SP93N-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems VFP32BP20LN-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems VFD26FM20N-2 Quick start guide

Empire Comfort Systems

Empire Comfort Systems LA21-1 User manual

Empire Comfort Systems

Empire Comfort Systems MANTIS BF28(B User manual

Empire Comfort Systems

Empire Comfort Systems DVP36DP31N-1 User manual

Empire Comfort Systems

Empire Comfort Systems EMBF11S Series User manual

Empire Comfort Systems

Empire Comfort Systems White Mountain Hearth DVCX36FP91K-3 Quick start guide

Empire Comfort Systems

Empire Comfort Systems WHITE MOUNTAIN HEARTH DVCP32-3 Quick start guide

Empire Comfort Systems

Empire Comfort Systems VFLL48SP(3 Quick start guide

Empire Comfort Systems

Empire Comfort Systems White Mountain Hearth MULTIFUNCTION REMOTE... Quick start guide

Empire Comfort Systems

Empire Comfort Systems BVD34FP Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVCP36PP3 SERIES Service manual

Empire Comfort Systems

Empire Comfort Systems Tahoe DVP36FP30-4NAT Quick start guide

Empire Comfort Systems

Empire Comfort Systems VFL20IN3 series User manual

Empire Comfort Systems

Empire Comfort Systems VFP36SP32EN-2 Quick start guide

Empire Comfort Systems

Empire Comfort Systems DVCT40CSP95P Planning guide

Empire Comfort Systems

Empire Comfort Systems DVP36PP32EN-3 Series Quick start guide

Empire Comfort Systems

Empire Comfort Systems LTH1118ST-1 User manual

Empire Comfort Systems

Empire Comfort Systems DVCD32FP30P-1 Quick start guide

Empire Comfort Systems

Empire Comfort Systems INTERMITTENT PILOT DVCD36FP70 User manual

Empire Comfort Systems

Empire Comfort Systems VFLB36FP30N User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual