Emerson Unidrive M700 Installation and operating instructions

This Application Note applies to the Unidrive M700 Drive Series

Saving and Restoring Unidrive M700 drive parameters

This application note will describe how to save and then restore parameters to a

Unidrive M700 using the NV Media Card. The NV Media Card is made up of two individual

parts fitted together: the SD-CARD-ADAPTOR and a SD memory card.Control Techniques

sells the CTSDG8GB SD card and the SD-CARD ADAPTOR. Below are pictures of an actual

SD-CARD-ADAPTOR fitted with the CTSDG8GB SD card. For all references to NV Media

Card following in this document it will be assumed the NV Media Card will consist of both the

SD-CARD-ADAPTOR and SD memory card in order to save and restore any drive parameters.

Before performing any of the parameter restoration operations below make sure the drive is

not enabled and there is no voltage applied to control terminal 31.

Saving Unidrive M700 drive parameters using the NV Media Card:

The following steps are needed to program a new NV Media Card or anytime the user wishes

to save a new backup project to the NV Media Card residing in the working drive. In order to

gain access to the drive NV Media Card the drive keypad will need to be removed as shown in

Figure 1. The drive keypad can be installed or removed while drive is powered on.

Application Note

M700

AN0006

Rev-02-9/20/2016

Warning: Be aware of possible live terminals when installing the keypad with power on.

Figure 1

To install, align the keypad and press gently in the direction shown in Figure 1 until it clicks into

position. To remove, reverse the installation instructions.

Once the keypad has been removed the NV Media Card can be installed into the drive as

shown in Figure 2. The NV Media Card can also be installed with drive power on, but make

sure the drive is disabled and there in no voltage applied to control terminal 31.

Installing the NV Media Card:

The NV Media Card is located at the top of the module under the drive display (if

installed) on the left-hand side. Ensure the NV Media Card isinserted with the contacts

facing the left hand side of the drive as seen in Figure 2 (1).The NV Media card installed

into the drive in Figure 2 (2) below.The drive only communicates with the NV Media

Card when commanded to read or write, meaning the card may be "hot swapped",

however, do not remove the NV Media Card until the Read or Write operation has

completed.

Figure 2

Once the NV Media card has been installed into the drive as shown in Figure 2 (2) the drive

keypad will need to be replaced and drive powered on in order to program the NV Media card.

Using the drive keypad scroll up or down to drive parameter 00.030. Press the keypad ‘M’ so

that ‘None’ is flashing and then using the up arrow change to ‘Program’ and press the Red

Reset button.

A small flashing period will flash next to left hand side of ‘00.030’ during the programming of

the NV Media card. Parameter 00.030 will change back to ‘None’ once the programming is

complete. The NV Media card now has a backup set of drive parameters that can be used to

restore parameters in this drive or any replacement drive of the same size and voltage ratings.

Restoring Unidrive M700 drive parameters using the NV Media Card:

The following steps are needed to program a new out of the box M700 drive or replacement

M700 drive that has an incorrect set of drive parameters.

Remove the drive keypad and install the NV Media card that has the backup drive parameters

stored on it as shown in Figure 1 and Figure 2 and apply power to the drive. Make sure the

drive is not enabled and there is no voltage applied to control terminal 31. Using the drive

keypad scroll up or down to drive parameter 00.030. Press the keypad ‘M’ so that ‘None’ is

flashing and then using the up arrow change to ‘Read’ and press the Red Reset button.

A small flashing period will flash next to left hand side of ‘00.030’ during the programming of

the M700 drive. Parameter 00.030 will change back to ‘None’ once the programming is

complete. Cycle power to the drive and the newly programmed M700 drive is now ready for

use.

Resources

Unidrive M700 User Guide

Unidrive M700 Parameter Reference Guide

Guides, can be found on our website: www.emersonindustrial.com/en-US/controltechniques

You can email to techsupport.[email protected]

You can call Technical Support at 952-995-8000, 24/7/365

Other manuals for Unidrive M700

4

Table of contents

Other Emerson DC Drive manuals

Emerson

Emerson Control Techniques Focus 3N User manual

Emerson

Emerson MP25A4 User manual

Emerson

Emerson unidrive sp User manual

Emerson

Emerson Unidrive HS72 User manual

Emerson

Emerson COPELAND EVA3 Manual

Emerson

Emerson PACMotion VFD Series User manual

Emerson

Emerson EV2000 Series User manual

Emerson

Emerson Mentor MP Assembly instructions

Emerson

Emerson Unidrive M200-01100017 User manual

Emerson

Emerson unidrive sp Instruction Manual

Emerson

Emerson Quantum MP User manual

Emerson

Emerson Mentor MP Assembly instructions

Emerson

Emerson Control Techniques Epsilon Ei User manual

Emerson

Emerson Copeland EVH Series User manual

Emerson

Emerson Unidrive M700 User manual

Emerson

Emerson Copeland EVM Series User manual

Emerson

Emerson Bettis RTS User manual

Emerson

Emerson E300 Series Guide

Emerson

Emerson unidrive m200 User manual

Emerson

Emerson Dixell XEV23D Wiring diagram

Emerson

Emerson E Series User manual

Emerson

Emerson Quantum MP QMP45A4 User manual

Emerson

Emerson EV3150B Instruction Manual

Emerson

Emerson Control Techniques Epsilon Eb Series User manual

Popular DC Drive manuals by other brands

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS user manual

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Technical description

Chamberlain Garog

Chamberlain Garog D Series operating manual

Parker

Parker PDS Series user guide

Festo

Festo DGC G Series Repair instructions

Binks

Binks QS-5012-1-CE Service manual

Danfoss

Danfoss VLT 2800 Series Quick setup

ABB

ABB ACQ580-01 Series Quick installation and start-up guide

YASKAWA

YASKAWA CANopen SI-S3 Technical manual

GE

GE D20A6 instructions

Unex

Unex MC-D-250-1000-050W-TW operating manual

Geckodrive

Geckodrive G213V manual

ABB

ABB RSYC-01 user manual

Rockwell Automation

Rockwell Automation PowerFlex 700S Programming manual

WEG

WEG DeviceNet CFW500 user manual

Siemens

Siemens SINAMICS G List manual

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Operating instructions & installation instructions

SOMFY

SOMFY JR RU 30 instructions